• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.5
• /
• pp.23-29
• /
• 1991

Uncertainty is studied in the measurements of average packing density, thickness of packed spheres and transmittance in the experiments to study the effect of the bed height and the existence of the bed side walls on the transmittance of radiative energy through packed spheres. The packing density of the bed is obtained by counting the number of the spheres packed in three pipes with different heights. The bed height of the packed spheres is estimated from the number of spheres contained in the bed by using the relation between the bed height and the sphere number. The transmittance is obtained by dividing the intensity of the transmitted laser beam by the incoming-beam intensity. From the analysis, the uncertainity in the measurements of transmittance is shown to be less than 10.2%(95% coverage).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1042-1045
• /
• 2002

We have carried out two-beam interference experiments to form holographic gratings on amorphous $MgF_2$/As-Ge-Se-S multi-layer. In this study, holographic gratings have been formed using He-Ne laser(632.8nm). under different polarization combinations. The diffraction efficiency was obtained by +1st order intensity. The maximum diffraction efficiency of As-Ge-Se-S single layer and $MgF_2$/As-Ge-Se-S multi-layer were 0.8% and 1.4%

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.3
• /
• pp.763-770
• /
• 1995

Gas flow characteristics within the cylinder is important factors in impoving lean combustion stability. This paper shows the effects of various flow fields generated by a swirl control valve(SCV) on combustion process in a 4-valve spark ignition engine. An impulse swirl/tumble meter was used to elucidation the steady-state flow characteristics, and a rotating grating type LDV was developed to measure the mean velocity and tunbulence intensity in relation to the crank angle. These methodologies were applied to clarify the correlation between gas flow characteristics and combustion stability at a lean air fuel ratio. An analysis of the correlation revealed the gas flow conditions required to optimize a lean-burn system.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.755-759
• /
• 2000

The determination of surface topography is believed to be extremely important in the areas of contact mechanics, adhesion and friction. In order to describe topography of various frictional surface. the wear test was carried out under different experimental conditions in dry friction. And fractal descriptors was applied to frictional surface of laser modified steel with image processing System. These descriptors to analyze surface structure are fractal dimension. Surface fractal dimension can be determined by sum of intensity difference of surface pixel. Topography of frictional surface can be effectively obtained by fractal dimensions.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.2
• /
• pp.48-56
• /
• 1995

The operating characteristics, such as, the threshold gain, lasing frequency, and longitudinal intensity profile, etc., of 1.55$\mu$m DFB laser diode with index and/or gain grating structures and with one side AR-coated mirror have been analyzed. From this analysis, the optimum design parameters have been shown that ${\Delta}{\Omega}$ (the phase difference between index grating and gain grating) is 0 or ${\pi}$, (xL)$_{r}$=1~3 and (xL)$_{i}$=0.5~0.9. It has been also shown that the modal selectivity and intensity uniformity of the DFB lasers with .DELTA..OMEGA.=0 are ~1.2 times better thatn those of the DFB lasers with ${\Delta}{\Omega}$= ${\pi}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.4
• /
• pp.404-409
• /
• 2004

We fabricated photo-sensor for fluorescence detection in LOC. LOC is high throughput screening system. Our LOC screens biochemical reaction of protein using the immunoassay, and converts biochemical reaction into electrical signal using LIF(Laser Induced Fluorescence) detection method. Protein is labeled with rhodamine intercalating dye and finger PIN photodiode is used as photo-sensor We measured fluorescence emission of rhodamine dye and analyzed tendency of fluorescence detection, according to photo-sensor size, light intensity, and rhodamine concentration. Detection current was almost linearly proportional to two parameters, intensity and concentration, and was inversely proportional to photo-sensor size. Integrated LOC consists of optical-filter deposited photo-sensor and PDMS microchannel detected 50 (pg/${mu}ell$) rhodamine. For integrated LOC including light source, we used green LED as the light source and measured emitted fluorescence.

• Journal of the Optical Society of Korea
• /
• v.20 no.6
• /
• pp.686-693
• /
• 2016

The analytical expressions for a partially coherent flat-topped vortex hollow beam propagating in uniaxial crystals orthogonal to the optical axis are derived, and the intensity and coherent vortex properties of partially coherent flat-topped vortex hollow beam propagation in uniaxial crystals orthogonal to the optical axis are analyzed by numerical examples. The influence of beam order parameter N, topological charge M, the coherence length and the ratio of refractive indices $n_e/n_o$ of uniaxial crystals on the normalized intensity distribution and coherent vortex of a partially coherent flat-topped vortex hollow beam propagating in uniaxial crystals are discussed in detail.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.11C no.3
• /
• pp.75-80
• /
• 2001

Holographic polymer dispersed liquid crystals (HPDLCs) have fabricated by irradiating an Ar-ion laser ( ${\lambda}$=514nm) at various intensity on LC/acrylate monomer mixtures which were sandwitched between two ITO coated glass plates. Monomer systems were composed of dipentaerythritol-hydroxy penta acrylate (DPHPA, f=5)/monofunctional acrylate monofunctional monomers. The LC used in this system was E7 (BL001, Merck). Gratings were fabricated by periodic interference of twobeams. Reflection efficiency-irradiation intensity-monomer type relationships were obtained from the UV-visible spectra of the HPDLC films. Peaks were found at a bit smaller wavelength than 514nm, due to the shrinkage of mixture volume upon polymerization. Real time measurements of diffraction efficiency have been obtained according to monomer types and LC contents.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.11C no.3
• /
• pp.91-95
• /
• 2001

Reflective holographic polymer dispersed liquid crystal(HPDLC) device has a multilayer structure consisting of alternate layers of polymer and liquid crystal droplets. Periodic modulation of a refractive index reflects light of a specific wavelength in accordance with Braggs law. Samples cured isotropically were illuminated with an Argon-ion lase at 514nm. We optimized the reflcetion efficiency of HPDLC as a function of monomer functionality, LC composition and irradiation intensity. The properties of the HPDLC films were observed by UV-visible spectroscopy. We found that the maximum reflection efficiency depends on the monomer functionality, LC composition, and laser intensity. We expect these films could be used in full-color reflective display by stacking them to obtain a mixture of colors.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.93-99
• /
• 2011

This paper presents a new type of optical silicon accelerometer using deep reactive ion etching (DRIE) and micro-stereolithography technology. Optical silicon accelerometer is based on a mass suspended by four vertical beams. A vertical shutter at the end of the mass can only moves along the sensing axis in the optical path between two single-mode optical fibers. The shutter modulates intensity of light from a laser diode reaching a photo detector. With the DRIE technique for (100) silicon, it is possible to etch a vertical shutter and beam. This ensures low sensitivity to accelerations that are not along the sensing axis. The microstructure for sensor packaging and optical fiber fixing was fabricated using micro stereolithography technology. Designed sensors are two types and each resonant frequency is about 15 kHz and 5 kHz.