• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.644-650
• /
• 2012

This paper show the 2kW fiber laser cutting properties of SS400. The study was comparison of traditional 4kW $CO_2$ Laser cutting and 2kW Fiber laser cutting characteristics for the application of Industrial 2D Laser Cutting Machine. The laser used in this investigation was an IPG YLU-2000 multi-mode Ytterbium Fiber machine with a maximum power of 2000W and a wave length of 1070 nm. The laser was used in its Continuous Wave (CW) mode with an approximately top hat beam intensity distribution. Fiber laser high quality cuts at a large range of speeds (ranging from 2000 to 3800 mm/min) which has been obtained for the 2.3mm Sheet of SS400. 2kW power Fiber laser cut was able to max. 20mm sheets of SS400 (speed range from 650 to 850 mm/min). Fiber laser cutting used in conventional hole nozzle could cut 12mm SS400 but used in special dual cutting nozzle could cut 20mm SS400.

• Journal of the Korean Society of Safety
• /
• v.5 no.2
• /
• pp.50-57
• /
• 1990

A new technique for the measurement of surface roughness based on the intensity fluctuations of laser light backscattered from a moving surface has been introduced. This paper reports a method of measuring surface roughness using coherent optics and interferometry. Included are both the theory of the technique and experimental verification. The range of surface roughness which can be accurately measured by this method is also reported.

• Journal of information and communication convergence engineering
• /
• v.1 no.4
• /
• pp.228-232
• /
• 2003

The previous design work for very large final amplifier pumped by electron beam module was described from the point of view of energy characteristics. In this work, the design problems for phase front distortion, ASE, and gain control in large aperture amplifier are presented in detail.

• Journal of the Optical Society of Korea
• /
• v.8 no.1
• /
• pp.21-28
• /
• 2004

When femtosecond laser pulses are focused inside the bulk of transparent materials, the intensity in the focal volume becomes high enough to produce permanent structural modifications. This technique has been applied to fabricate three-dimensional photonic structures such as optical memory, waveguides, gratings, and couplers inside a wide variety of transparent materials. In this paper, we review the fabrication of optical elements in glasses with femtosecond laser pulses, including the fabrication of waveguides, couplers, Bragg gratings, zone plates, holographic memory, and micro holes.

• Korean Journal of Acupuncture
• /
• v.40 no.4
• /
• pp.141-148
• /
• 2023

Objectives : The purpose of this study is to investigate on the application of the yttrium aluminum garnet (YAG) lasers for acupoints irradiation. Methods : We conducted a systematic search for peer-reviewed studies published from inception to November 2023, in the following electronic databases: PubMed, Scopus, and Web of Science in English, Science ON, Oriental Medicine Advanced Searching Integrated System (OASIS) and Research Information Sharing Service (RISS) in Korean, and China National Knowledge Infrastructure (CNKI) and Wanfang in Chinese, and Japan Science Technology Information Aggregator, Electronic (J-STAGE) and Citation Information by NII (CiNii) in Japanese. Inclusion criteria were original articles including clinical and experimental studies related with YAG lasers for acupoints including Ashi or meridian sinews. Results : Among the 8 selected studies, there were 7 studies on human subjects and 1 study on animals, 7 studies on Nd:YAG (1,064 nm) laser, and 1 study on Er:YAG (2,940 nm) laser. A total of 16 acupoints were used, 15 of which were in the face and 1 of which was located in the foot. In addition, there were two studies using Ashi. 4 studies looked at the effect of pain relief, 2 studies looked at safety, 1 study looked at changes in blood flow, and 1 study looked at the effect of skin care. There were no reported adverse events, and the YAG laser was confirmed to be safe and effective in pain relief, beautifying the skin, and increasing blood flow. Conclusions : We suggest that high intensity YAG lasers can be applied to laser acupuncture or laser moxibustion. YAG lasers are considered to be worth using for various clinical indications of Korean medicine because of photobiomodulation effects, analgesic action, and deep penetration depth. Further scientific research and clinical evidences should be warranted.

• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.80-85
• /
• 2009

An experimental study of energy absorption and x-ray emission from ultrashort laser pulse irradiation of in-situ produced solid clusters has been performed. Silver clusters produced by a 30 mJ, 300 ps laser pulse were irradiated up to an intensity of $3{\times}10^{17}\;W/cm^2$ by a 70 mJ, 45 fs compressed laser pulse from the same Ti:sapphire laser. Absorption of the laser light exceeding 70% was observed, resulting in an x-ray yield (>1 keV) of ${\sim}60{\mu}J$ pulse. This may constitute a much simpler means of intense x-ray generation using ultrashort laser pulses as compared to the irradiation of structured / pre-deposited cluster targets, and it offers higher x-ray conversion efficiency than that from gas clusters and planar solid targets.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.104-109
• /
• 2021

In this paper, we experimentally demonstrate a self-seeding FP-LD (Fabry Perot Laser Diode) to verify the possibility of a new tunable light source that can be used in WDM-PON (Wavelength Division Multiplexing - Passive Optical Network) system. The conventional implementation of WDM-PON using a tunable light source has a disadvantage that the center wavelength of the AWG (Arrayed Waveguide Grating) device and the tunable light source must be precisely aligned. However, the proposed tunable light source has the advantage that the tunable wavelength is automatically aligned with the center wavelength of the AWG as well as simple structure. The implemented tunable light source had a tunable band of about 14 nm or more, and the maximum RIN (Relative Intensity Noise) of about -124 dB/Hz, which showed the possibility of modulating 10 Gb/s signal by an external modulator.

• Journal of Oral Medicine and Pain
• /
• v.20 no.2
• /
• pp.327-334
• /
• 1995

In order to observe the influence of pulsed Nd:YAG laser at its out-of-contact with dentin on tooth temperature, we have applied pulsed Nd:YAG laser to 2mm thick dentin sample at a point of contact and from a distance of 1mm, 2mm, 3mm and 4mm with an energy of 0.3W, 0.5W, 0.8W, 1.5W and 2.0W. They were exposed to periods of 3 seconds, 6 seconds, 9 seconds and 15 seconds respectively and measured temperature changes. The results as follows : 1. When the time ad intensity of power were constant, the temperature changes on dentin of tooth depended on the distance. The temperature increased when the laser intensity increased bu two other conditions were contact. 2. At the point of contact, the temperature has risen over $5^{\circ}C$ regrdless of intensity of the power or the time. However, there was $5^{\circ}C$ fluctuation with 0.3 W for 3 seconds treatment. 3. The temperature change was less than $5^{\circ}C$ thermal change at the distance of 1mm and 2mm respectively when lased for 3 seconds, 6 seconds, 12 seconds and 15 seconds with 0.3 W. Similar results were observed at 3 and 6 seconds treatment with 0.5 W and at 3 seconds treatment with 0.8 and 1.0W respectively. 4. It showed less than 5(C thermal change when lased for 3 seconds, 6 seconds, 9 seconds, 12 seconds and 15 seconds with 0.3W at the distance of 3mm and 4mm. The same results were seen in 3 seconds, 6 seconds and 9 seconds treatment with 0.5W and in 3 seconds with 0.8W and 1.0W respectively. As we have seen the above, the results has indicated that pulsed Nd:YAG lasing at its off contact on dentin of 2mm thickness will not cause irreversible changes if lasing intensity, lasing distance and lasing time are appropriate.

• Journal of information and communication convergence engineering
• /
• v.4 no.3
• /
• pp.101-104
• /
• 2006

We have investigated the spectral characteristics of the semiconductor lasers locked to the sidebands of the master laser in this paper, which were expressed by a series of the Bessel function. The numerical model for the semiconductor lasers based on the typical Lang's equation has been extended in order to take into account the simultaneous injection of the multiple sidebands of the directly modulated ML. We analyses characteristics of direct intensity modulation.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.6
• /
• pp.380-389
• /
• 2006

A new laser-based ultrasonic receiver that is based on multi-channel interferometry is shown to be well suited for robust and sensitive detection of ultrasound in industrial environment. The proposed architecture combines random-quadrature detection with detector arrays and parallel multi-speckle processing. The high sensitivity is reached, thanks to the random phase distribution of laser speckle caused by surface roughness. High-density parallel signal processing is achieved by using a simple demodulation technique based on signal rectification. This simple detection scheme is also demonstrated for rejection of the laser intensity noise, making possible the use of lower cost laser without reduction in performances. Results demonstrating this new principle of operation and its performances are presented.