• Proceedings of the Optical Society of Korea Conference
• /
• 1990.02a
• /
• pp.26-28
• /
• 1990

Cw arc 램프로 펌핑하는 Alexandrite 레이저의 형광을 optical Spectrum Analyzer를 이용하여 측정하였다. Vibronic 천이에 해당하는 광대역 형광 스펙트럼이 관측되었고, arc 램프 입력에 따른 peak 형광의 세기 및 peak intensity 파장의 입력 power 의존성을 조사하였다. 형광의 세기는 입력 power에 따라 0.16 /kw의 비율로 증가하였고, peak intensity 파장은 입력 power가 5kw 까지는 5 nm/kw 비율로 장파장쪽으로 이동하였다.

• Laser Solutions
• /
• v.9 no.3
• /
• pp.7-13
• /
• 2006

Auto focusing system to find optimized focal position of laser beam used for material process has been investigated by using fiber confocal method. Wavelength of laser diode (LD) and diameter of single-mode fiber are 780nm and $5.3{\mu}m$, respectively. Intensity distributions of beam reflected from the surface of mirror and silicon bare wafer have been observed in a gaussian form. Experimental results show that focal position obtained by LD is shifted from one observed from surface scribed by laser about $80{\mu}m$. It is due to the difference of wavelength and each divergence of between LD and laser used for material process. It is confirmed that auto focusing control system through position calibration has operated steadily.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.285-287
• /
• 2009

When the laser diode is operated with continuous current, the light intensity from the laser diode deceases with time due to the temperature rise in the active layer. The phenomena, which is often called as DROOP, should be minimized in order to be used as a light source for the laser beam printer. We experimently examined the influences of the laser parameters such as threshold current, differential quantum efficiency on droop. It was found that decreasing the differential quantum efficiency of the laser diode is the effective way to minimize droop.

• Journal of Welding and Joining
• /
• v.22 no.6
• /
• pp.30-35
• /
• 2004

Laser welding is obviously an attractive method to join small, thin parts such as small stainless steel tubes, but it is very sensitive to the joint clearance and tolerance, and this makes laser welding difficult to obtain consistent welding qualities over time. Recently, Plasma Augmented Laser Welding(PALW) is being developed to solve these problems. In this study, plasma arc welding(PAW) was introduced to join conventional V-grooved butt joint of thin stainless steel strips using single laser heat source in manufacturing small stainless steel tubes. The effect of the welding speed enhancement is investigated by the experiments. Effects of welding directions, distance between the heat sources and intensity of arc heat source on the optimal welding speed was investigated. Through this research, it was confirmed that PALW process has higher welding speed and robustness than laser welding process.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.328-340
• /
• 1991

The combustion process in the combustion chamber has been investigated by taking pressure, temperature, chemical equilibrium and the shape of flame. To predict temperature of a flame in a combustion chamber is one of very important problems in the field of combustion and the temperature is a important factor of ignition and counteraction to inflammation. In this paper, the flame temperature was determined by the method of the Rayleigh scattering of Ar-Ion Laser (514.5nm). The Rayleigh scattering has been got considerably attention because of its strong cattering intensity. As a result, it is shown that I can measure the shape of flame by schlieren photography and that I can get the flame temperature variation in constant volume combustion chamber by Laser Rayleigh Scattering.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.190-196
• /
• 2006

Transparent materials are widely used in the fields of optic parts and bio industry. We have experiment to find out the characteristics of the micromachining inside transparent materials using femtosecond laser pulses. With its non-linear effects by very high peak intensity, filament (plasma channel) was formed by the cause of the self-focusing and the self-defocusing. Physical damage could be found when the intensity is high enough to give rise to the thermal stress or evaporation. At the vicinity of the power which makes the visible damage or modification, the structural modification occurs with the slow scanning speed. According to the polarization direction to the scanning direction, the filament quality is quite different. There is a good quality when the polarization direction is parallel to the scanning direction. For fine filament, we could suggest the conditions of the high numerical aperture lens, the short shift of focusing point, the low scanning speed and the low power below 20 mW. As the examples of optics parts, we fabricated the fresnel zone plate with the $225{\mu}m$ diameter and Y-bend optical wave guide with the $5{\mu}m$ width.

• Korean Journal of Optics and Photonics
• /
• v.23 no.3
• /
• pp.103-107
• /
• 2012

We investigate the dependence of the output of a mode locked Yb-doped fiber laser on incident intra-cavity intensity on a semiconductor saturable absorber mirror (SESAM). To vary the incident intra-cavity intensity, we change the beam spot size on a SESAM by varying the focal length of a lens installed in the front of the SESAM.

• Korean Journal of Optics and Photonics
• /
• v.9 no.4
• /
• pp.231-235
• /
• 1998

Passively Q-switched, laser diode(LD) end-pumped Nd:YAG laser was demonstrated by using $Cr^{4+}$:YAG as a saturable absorber. In addition , we could calculate an excitation efficiency, which is an important parameter to evaluate the pumping geometry, directly by measuring the absorbed power in Nd:YAG at threshold condition. We found that output parameters such as average power, pulse duration, and repetition rate strongly depended on the low intensity transmission of $Cr^{4+}$:YAG and driving current of lase diode. The maximum Q-switched output power of 1 W was obtained with 40 kHz repetition rate. The pulse duration was varied from 50 ns to 200 ns.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.78-87
• /
• 2016

Red blood cells (RBCs) are customarily adhered to a bio-functionalised substrate to make them stationary in interferometric phase-imaging modalities. This can make them susceptible to receive alterations in innate morphology due to their own weight. Optical tweezers (OTs) often driven by Gaussian profile of a laser beam is an alternative modality to overcome contact-induced perturbation but at the same time a steeply focused laser beam might cause photo-damage. In order to address both the photo-damage and substrate adherence induced perturbations, we were motivated to stabilize the RBC in OTs by utilizing a laser beam of ‘arbitrary intensity profile’ generated by a source having cavity imperfections per se. Thus the immobilized RBC was investigated for phase-imaging with sinusoidal interferograms generated by a compact and robust Michelson interferometer which was designed from a cubic beam splitter having one surface coated with reflective material and another adjacent coplanar surface aligned against a mirror. Reflected interferograms from bilayers membrane of a trapped RBC were recorded and analyzed. Our phase-imaging set-up is limited to work in reflection configuration only because of the availability of an upright microscope. Due to RBC’s membrane being poorly reflective for visible wavelengths, quantitative information in the signal is weak and therefore, the quality of experimental results is limited in comparison to results obtained in transmission mode by various holographic techniques reported elsewhere.

• Journal of Dental Anesthesia and Pain Medicine
• /
• v.22 no.1
• /
• pp.19-27
• /
• 2022

Background: Myofascial pain dysfunction syndrome (MPDS) is the most common type of temporomandibular disorder. This study compared the efficacies of low-level diode laser therapy (LLLT) and laser acupuncture therapy (LAT) in the treatment of MPDS. Methods: This double-blind randomized controlled clinical trial included 24 patients with MPDS who were randomly divided into two equally sized groups. Patients in the LLLT group received 12 sessions of low-level diode laser irradiation applied to the trigger points of the masticatory muscles during 1 month. The same protocol was also used in the LAT group according to the specific trigger points. We measured pain intensity and maximum mouth opening in both groups at baseline, during treatment, and 2 months after treatment completion. Results: The pain intensities decreased from 6.58±1.31 to 0.33±0.65 and from 7.08 ± 1.37 to 0 in the LLLT and LAT groups, respectively. The maximum mouth openings increased from 32.25 ± 8.78 mm to 42.58 ± 4.75 mm and from 33 ± 6.57 mm to 45.67 ± 3.86 mm in the LLLT and LAT groups, respectively. Pain intensity (P = 0.839) and level of maximum mouth opening (P = 0.790) did not differ significantly between the groups. Conclusion: Our results showed similar efficacy between LLLT and LAT in the treatment of MPDS signs and symptoms.