• 열처리공학회지
• /
• 제9권3호
• /
• pp.177-186
• /
• 1996

Surface alloying of Ti alloy by $CO_2$ laser is able to produce few hundred micrometers thick TiN or TiC surface-alloyed layer with high hardness on the substrate by injecting reaction gas($N_2$ or $CH_4$). Laser surface alloying by means of process control is in many applications essential in order to obtain predictable hardening layer. This research has been investigated the effect of such parameters on TiN and TiC gas alloying of Ti-6Al-4V alloy by $CO_2$ laser. The maximum surface hardness of TiN layer was obtained 1750Hv on the conditions of 0.8kW laser power, 0.8m/min scanning speed and 100% $N_2$ atmosphere. However, the maximum hardness of TiC formation layer after laser treatment was about 630Hv. As scanning speed was increased, the hardness and depth of these layers were decreased at constant laser power.

• 대한기계학회논문집A
• /
• 제35권12호
• /
• pp.1663-1668
• /
• 2011

자동차 차체를 제작하는 프레스 금형의 가공공정 중 제품의 형태를 완성하는 드로잉 공정 및 불필요한 부분을 절단하는 트리밍 공정은 그 공정의 특성상 금형의 마모가 심하기 때문에 금형의 내마모성을 향상시키기 위한 표면경화처리가 요구되고 있다. 따라서 본 연구에서는 프레스 금형에 레이저 표면처리기술을 적용하기 위한 실험을 실시하였다. 드로잉 공정 및 트리밍 공정에 적합한 표면경화처리를 위해 다이오드 레이저를 이용하여 시험편의 평면부 및 모서리부를 열처리하였으며, 각각의 적정 열처리 조건을 도출하였다. 또한 시험편의 재료에 따른 열처리 특성을 비교하기 위해 구상흑연 및 편상흑연 주철을 사용하여 실험을 진행하였다. 실험 결과, 재료에 따른 열처리 특성에 차이가 있다는 것을 확인하였으며, 적정 열처리된 조건에서의 경화부는 모재에 비하여 약 3배 정도의 경도상승을 나타내었다.

• 열처리공학회지
• /
• 제8권3호
• /
• pp.182-186
• /
• 1995

SCM440, which is widely used as the diesel engine piston of vessel, has been hardened by a $CO_2$ laser with the wavelength of $10.6{\mu}m$. Laser hardening experiment has been carried out for the condition of a laser power 1kW, the travel speed between 0.4 and 1.5m/min, and a rectangular-Gaussian beam. Residual stress has been measured by using middle point technique of half value width of X-ray diffraction method. It was found that the compressive residual stress with the range between 400 and 600MHz has distributed in the laser hardening zones and the tensile residual stress between 100 and 200MHz has distributed in the boundary of hardening zones.

• 열처리공학회지
• /
• 제13권5호
• /
• pp.318-323
• /
• 2000

The planarization of rough polycrystalline diamond films synthesized by DC arc discharge plasma jet CVD (chemical vapor deposition) was attempted using KrF excimer laser pulses. The effects of laser incidence angle and reaction gases (ozone and oxygen) on etching rate of diamond were studied. The temperature change of diamond and graphite with different laser fluences was calculated by computer simulation to explain the etching behavior of diamond films. The threshold energy density from the experiment for etching of pure crystalline diamond was about $1.7J/cm^2$ and fairly matched the simulation value. Preferential etching of a particular crystallographic plane was observed through scanning electron microscopy. The etching rate of diamond with ozone was lower than that with oxygen. When the angle of incidence was $80^{\circ}$ to the diamond surface normal, the peak-to-valley surface roughness was Significantly reduced from $20{\mu}m$ to $0.5{\mu}m$.

• 열처리공학회지
• /
• 제13권3호
• /
• pp.170-176
• /
• 2000

A novel method for improving the adhesion of diamond films on cemented carbide tool inserts has been investigated. This method is based on the formation of a compositionally graded interface by developing a microrough surface structure using a pulsed laser process. Residual stresses of diamond films deposited on laser modified cemented carbides were measured as a function of substrate roughness using micro-Raman spectroscopy. The surface morphology and roughness of diamond films and cemented carbides were also investigated at different laser modification conditions. It was found that the increasing interface roughness reduced the average residual stress of diamond films, resulting in improved adhesion of diamond films on cemented carbides.

• 열처리공학회지
• /
• 제6권4호
• /
• pp.230-236
• /
• 1993

The laser beam hardening has been experimentally tried to find the hardened characteristics of STD11. Experiment was performed on the optimum hardening condition with 2kW $CO_2$ laser. The microstructure of the hardened layers was observed using the microscope. The hardened zones exhibits very high Vickers microhardness of 720 Hv, however, the deoxidation was observed under the surface of hardened area. The case depth of hardened zones is about 0.6mrn and case width is 4mm. FEM-simulation on laser surface hardening of STD11 steel are described. With the proper assumption of the absorbed energy density, the calculated case depth and width in 2 kW $CO_2$ laser hardening were in good agreement with the experimental result. It was found that there is optimum absorbed energy density of STD11.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(III)
• /
• pp.406-411
• /
• 2003

This paper deals with the effect of laser material processing on the EMU production technique. Material processing with lasers takes advantage of all the characteristics of laser light. The high energy density and directionality achieved with lasers permits strong localized heat- or photo-treatment of materials with spatial resolution below one micrometer. The pulsed and mono-chromatic light allows the control of depth of heat treatment or selective excitation. The laser beam can be moved to process large areas, is a sterile tool and is no subject to wear and tear. Using laser processing have taken more interests in EMU production for improving the rigidity, weight reduction, crash durability, and cost savings so that their application to auto-bodies has been increased.

• 대한금속재료학회지
• /
• 제50권3호
• /
• pp.224-232
• /
• 2012

In this study, the effect of hot-stamping heat treatment on the microstructure and hardness of TWB(Tailor Welded Blank) laser joints in Al-Si-coated boron steel and Zn-coated DP(Dual Phase)590 steel was investigated. In the TWB joints without heat treatment, hardness profiles showed local hardness deviation near the fusion zone. However, there was no hardness deviation in the heat treated specimen and its hardness was higher than that of the one without the heat treatment, due to a fully martensite microstructure. In the TWB joints of both the boron and DP steels, the maximum hardnesses were observed at the HAZ(Heat Affected Zone) near the base metal, and the hardness decreased gradually to the base metal. In the heat treated joints, the hardnesses of the HAZ and the base metal of the boron steel side were similar to the maximum hardness of the weld, while those of the HAZ and the base metal of the DP steel side were higher than the maximum hardness.

• 열처리공학회지
• /
• 제34권6호
• /
• pp.281-286
• /
• 2021

Arc ion plating (AIP), laser cladding, and nitriding are methods that can prevent mold damage or repair and create cracks and breakages on the die surface. The dissolution and soldering behavior of coated SKD61 by using arc ion plating, laser cladding, and nitriding was investigated. The structure of the coating was investigated as a function of deposition conditions by X-ray diffraction and the crystallographic orientation was determined using the texture factor. The TiAlN film deposited with AIP showed excellent corrosion resistance in the molten aluminum alloy at 680℃. In this paper, we have detailed the corrosion and mass loss phenomena associated with these steel-cast metal interactions.

• Journal of Welding and Joining
• /
• 제19권2호
• /
• pp.228-234
• /
• 2001

A methodology is developed and used to evaluate the response sensitivity of the thermal systems to variations in their design parameters. Technique for computing the sensitivity of temperature distributions to changes in processing parameters needed to decide the more effective laser input parameters for laser surface hardening treatment is considered. In this study, a state equation governing the heat flow in laser surface treatment is analyzed using a three-dimensional finite element method and sensitivity data of the processing parameter obtained using a direct differentiation method is applied to the sensitivity analysis. The interesting processing parameters are taken as the laser scan velocity and laser beam radius ( $r_{ b}$), and the sensitivities of the temperature T versus v and $r_{b}$ are analyzed. These sensitivity results are obtained with another parameters fixed. To verify the numerical analysis results, hardened layer dimensions (width and depth) of the numerical analysis are compared with the experimental ones.nes.