• 대한기계학회논문집A
• /
• 제35권12호
• /
• pp.1655-1662
• /
• 2011

본 연구는 레이저를 이용한 스테인리스강의 용접성 평가에 대한 연구이다. 사용된 금속인 스테인리스 스틸은 녹 및 열적변형이 우수하여 다양한 적용 분야를 가지고 있다. 본 연구는 50 W 레이저 열원에 자기장을 적용하여 스테인리스 스틸에 기계적 성질을 향상 시키는데 목적을 두고 있다. 이에 따른 기계적 성질을 분석하기 위하여 수치적 해석, 인장강도, 형상 및 미세조직, 경도 시험 등을 수행하였다. 결과적으로 수치적 해석을 통한 금속 용융점에서의 속도 증가, 인장강도 약 16 MPa 상승, 용융부에 섞임, 경도 약 7 Hv 상승으로 기계적 성질이 향상 되었다.

• 대한기계학회논문집B
• /
• 제35권10호
• /
• pp.1041-1046
• /
• 2011

본 연구에서는 레이저 쇼크 피닝으로부터 생성되는 마이크로 충격파를 정량적으로 측정하고 그 특성을 분석하였다. 레이저 쇼크 피닝은 금속 재료에서 압축 응력을 생성시키며 그 크기가 표면에서 극대화되는 특징을 가지고 있다. 펄스 Nd:YAG 레이저를 이용하여 스틸표면에 피닝 공정을 수행하였고 이에 따른 마이크로 충격파의 정량화 및 재료의 기계적 성질 변화에 대해 평가하였다. 실험적 접근으로 피에조소자를 사용하였으며 이를 통한 실제 충격파의 정량화를 제시하였다. 또한 재료 구조 특성, 재료 강도, 인장 시험 등의 기계적 특성을 분석하였다.

• 한국분말재료학회지
• /
• 제29권5호
• /
• pp.390-398
• /
• 2022

Recently, considerable attention has been given to nickel-based superalloys used in additive manufacturing. However, additive manufacturing is limited by a slow build rate in obtaining optimal densities. In this study, optimal volumetric energy density (VED) was calculated using optimal process parameters of IN718 provided by additive manufacturing of laser powder-bed fusion. The laser power and scan speed were controlled using the same ratio to maintain the optimal VED and achieve a fast build rate. Cube samples were manufactured using seven process parameters, including an optimal process parameter. Analysis was conducted based on changes in density and melt-pool morphology. At a low laser power and scan speed, the energy applied to the powder bed was proportional to ${\frac{P}{\sqrt{V}}}$ and not ${\frac{P}{V}}$. At a high laser power and scan speed, a curved track was formed due to Plateau-Rayleigh instability. However, a wide melt-pool shape and continuous track were formed, which did not significantly affect the density. We were able to verify the validity of the VED formula and succeeded in achieving a 75% higher build rate than that of the optimal parameter, with a slight decrease in density and hardness.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.71-76
• /
• 2013

Gas nitriding is a surface hardening process where nitrogen is introduced into the surface of a ferrous alloy. During fusion welding of nitrided carbon steel, the nitride inside weld metal is dissolved and generates nitrogen gas, which causes porosities - blow holes and pits. In this study, several laser welding processes such as weaving welding, two-pass welding, dual beam welding and laser-arc hybrid welding were investigated to elongate the weld pool to enhance nitrogen gas evacuation. The surface pits were successfully eliminated with elongated weld pool. However blowholes inside the weld metal were effective reduced but not fully disappeared.

• IMMUNE NETWORK
• /
• 제1권3호
• /
• pp.187-195
• /
• 2001

The expression of recombinant proteins fused to 26 kDa glutathione S-transferase (GST) extracted from Schistosoma japonicum represents an attractive system for purifiying proteins of interest in a single step using GST-affinity chromatography. In addition, the GST-tag is used conveniently for detecting fused proteins since its high solubility as well as its relatively small size rarely interferes with the biological activity of the fused protein. In this regard, the GST system is frequently applied for tracing fusion proteins in both prokaryotic and eukaryotic cells to elucidate the physiological interactions and functional compartments of proteins. To provide a further tool in analyzing GST-fusion proteins, a new monoclonal antibody, with a high specificity to the S. japonicum GST was produced. Methods: BALB/c mice were immunized both with recombinant S. japonicum GST proteins, and by the fusion of splenocytes from these mice with myeloma cells. From this, a new anti -GST monoclonal antibody, termed SARAH, was generated. The specificity and reactivity of this antibody was confirmed by ELISA and by Western blot analysis. Results: SARAH showed a high reactivity to recombinant GST and GST fusion protein but not with native mammalian GST proteins as derived from other species including humans, cows, rabbits and rats. The applicability of SARAH was further demonstrated by confocal laser scanning microscopy, where GST proteins that were expressed transiently in mouse fibroblast cells, were specifically detected without interference of endogenous GST. Conclusion: SARAH is new monoclonal antibody with a high specificity to recombinant GST proteins but not to endogenous GST in mammalian cells.

• 한국레이저가공학회지
• /
• 제13권3호
• /
• pp.19-26
• /
• 2010

In this study, fundamental experiment was conducted with various strength of UHSS (Ultra High Strength Steel) by $CO_2$ laser. And then, butt and lap joint laser welding with boron alloyed steel and Al-Si coated boron alloy steel have been done by changing laser beam feature, existence of gap and existence of coating layer to know welding characteristics of those materials. As a result, in case of fundamental experiment with various strength steel, hardening was found in the weld metal of all tested materials and softening was found at the heat affected zone of SGAFC 1180. In case of laser butt welding of UHSS, mechanical properties was improved by using small laser beam diameter and Al-Si coating layer caused fracture of weld metal. In case of laser lap welding of UHSS, Al-Si coating layer resulted in formation of intermetallic compound at the fusion boundary where fracture occurred. Al-Si coating layer caused lowering mechanical properties of weld metal.

• 제어로봇시스템학회논문지
• /
• 제17권3호
• /
• pp.277-282
• /
• 2011

This paper describes a sensor fusion-based semantic map building which can improve the capabilities of a mobile robot in various domains including localization, path-planning and mapping. To build a semantic map, various environmental information, such as doors and cliff areas, should be extracted autonomously. Therefore, we propose a method to detect doors, cliff areas and robust visual features using a laser scanner and a vision sensor. The GHT (General Hough Transform) based recognition of door handles and the geometrical features of a door are used to detect doors. To detect the cliff area and robust visual features, the tilting laser scanner and SIFT features are used, respectively. The proposed method was verified by various experiments and showed that the robot could build a semantic map autonomously in various indoor environments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.317-318
• /
• 2007

One of the important factors of the autonomous mobile robot is to build a map for surround environment and estimate its localization. This paper suggests a sensor fusion method of laser range finder and monocular vision sensor for the simultaneous localization and map building. The robot observes the comer points in the environment as features using the laser range finder, and extracts the SIFT algorithm with the monocular vision sensor. We verify the improved localization performance of the mobile robot from the experiment.

• 한국재료학회지
• /
• 제14권6호
• /
• pp.425-431
• /
• 2004

A laser welding was applied between sintered tip of Fe-Co-W and low carbon steel shank for the diamond saw blade. The welding characteristics and formation of defects were investigated carefully for the weld fusion zone in different welding condition. Dendrite arm spacing in weld bead decreased with decrease of heat input. Co and W increased and Fe decreased in the weld fusion zone with increase of the heat input. The corresponding change of composition was observed with the change of beam position. The maximum and total length of crack decreased with increase of the heat input. The crack in weld bead was propagated along the dendrite boundary and was caused mainly by the segregation of constituent during the solidification.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2003년도 Proceedings of ACRS 2003 ISRS
• /
• pp.1042-1044
• /
• 2003

A methodology of the integrating the similar color circle search of the spectral data and segmentation of the height data is developed. The method is then applied to study areas, and the results by IKONOS, LIDAR and data fusion are verified with the ground truth, and examined in terms of the accuracy. Results show that with the data fusion the accuracy are improved by about 15% in most of the study areas. The methodology for the detection of individual tree stands by data fusion is explored, and the utility of combinatorial use of the spectral and the height information is demonstrated.