• Journal of Biomedical Engineering Research
• /
• v.36 no.4
• /
• pp.115-122
• /
• 2015

A standard air flow generator system was developed to generate air flows of various levels simultaneously applied to two different air flow transducer modules. Axes of two identical standard syringes for spirometer calibration were connected with each other and driven by a servo-motor. Linear displacement transducer was also connected to the syringe axis to accurately acquire the volume change signal. The user can select either sinusoidal or square waveform of volume change and manually input any volume as well as maximal flow rate levels ranging 0~3 l and 0~15 l/s, respectively. Various volume and flow levels were input to operate the system, then the volume signal was acquired followed by numerical differentiation to obtain the air flow signal. The measured volumes and maximal air flow rates were compared with the user input data. The relative errors between the user-input and the measured stroke volumes were all within 0.5%, demonstrating very accurate driving of the system. In case of the maximal flow rate, relatively large error was observed when the syringe was driven very fast within a very short time duration. However, except for these few data, most measured flow rates revealed relative errors of approximately 2%. When the measure and user-input stroke volume and maximal flow rate data were analyzed by linear regression analysis, respectively, the correlation coefficients were satisfactorily higher than 0.99 (p < 0.0001). These results demonstrate that the servo-motor controls the syringes with enough accuracy to generate standard air flows. Therefore, the present system would be very much practical for calibration process as well as performance evaluation and comparison of two different air flow transducer modules.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.3
• /
• pp.162-173
• /
• 1996

Dry magnetic particle inspection(MPI) was performed to detect the surface defects of steel ingot cast billets. Magnetic properties of several materials were characterized by the measurement of the B-H hysteresis curve. The inspection results were evaluated in terms of the magnetizing current, temperature, and the amount of magnetic particles applied to billets. Magnetic flux leakage near the defect site of interest was measured and compared with the results of calculation by the finite element method in the case of direct magnetizing current. Direct and alternating magnetizing currents for materials were deduced by the comparison of the inspections. Results of the magnetic particle inspection by direct magnetizing current were compared with those of finite element method calculations, which were verified by measuring magnetic leakage flux above the surface and the surface defects of the material. For square rods, due to the geometrical effect, the magnetic flux density at the edges along the length of the rods was about 30% of that at the center of rod face for a sufficiently large direct magnetizing current, while it was about 70% for an alternating magnetizing current. Thus, an alternating magnetizing current generates rather uniform magnetic flux density over the rods, except for the region on the face across about 10 mm from the edge. The attraction of the magnetic particle by the magnetic leakage field was nearly independent of the surface temperature of the billets up to $150^{\circ}C$. However, the temperature should have been limited below $60^{\circ}C$ for an effective fixing of gathered magnetic particles to the billet surface using methylene chloride. We also found that the amount of applied magnetic particles tremendously affected the detection capability.

• The Korean Journal of Food And Nutrition
• /
• v.29 no.5
• /
• pp.670-676
• /
• 2016

In this study, we analyzed the utensils, covers and mats that were used for making meju, the shape of meju, and the heating method used for making meju from the 225 ways of preparing jang mentioned in the 32 volumes of the ancient cook books from 530 AD to 1950. The heating method of traditional meju bean and starch included 57 kinds of steaming, 59 of boiling, 21 of roasting + boiling, and 2 of cooking. The shape of meju included 41 kinds of egg, 27 of ball, 22 of lump, a kind of doughnut, 8 kinds of hilt, 6 of flat, 4 of chip, and a kind of square. Among the 72 gochoojang meju, the heating method of bean included 9 kinds of boiling, and 6 kinds of steaming; whereas the heating method of starch included 19 kinds of steaming of dough, 11 of rice cooking, and 5 of boiling of dough. The utensils for molding of bean meju were 49 kinds of straw sack, 14 of round straw container, 11 of heating bed, 7 of large straw bowl or Japanese-snailseed, 5 of jar, 4 of ditch, 3 of straw bowls, 2 of pottery steamer of dough, 2 of gourd, and a kind of long round bamboo bowl and sack of straw. The cover and the mat used for molding of meju included 36 kinds of straw, 17 kinds of paper mulberry leaf, 15 of wide straw seat, 14 of mugwort, 11 of pine tree leaf, 10 of soybean leaf, 6 of cocklebur leaf, 6 of sumac leaf, 6 of barley straw, 6 of mulberry leaf, 5 of fallen leaf, 5 of cogon grass, 4 of reed seat, 3 of scrap of cloth, 2 of Indian bean tree leaf, a kind of reed. There were only 5 kinds of hanging.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.377-377
• /
• 2012

Microprocessor technology now relies on copper for most of its electrical interconnections. Because of the high diffusivity of copper, Atomic layer deposition (ALD) $TaN_x$ is used as a diffusion barrier to prevent copper diffusion into the Si or $SiO_2$. Another problem with copper is that it has weak adhesion to most materials. Strong adhesion to copper is an essential characteristic for the new barrier layer because copper films prepared by electroplating peel off easily in the damascene process. Thus adhesion-enhancing layer of cobalt is placed between the $TaN_x$ and the copper. Because, cobalt has strong adhesion to the copper layer and possible seedless electro-plating of copper. Until now, metal film has generally been deposited by physical vapor deposition. However, one draw-back of this method is poor step coverage in applications of ultralarge-scale integration metallization technology. Metal organic chemical vapor deposition (MOCVD) is a good approach to address this problem. In addition, the MOCVD method has several advantages, such as conformal coverage, uniform deposition over large substrate areas and less substrate damage. For this reasons, cobalt films have been studied using MOCVD and various metal-organic precursors. In this study, we used $C_{12}H_{10}O_6(Co)_2$ (dicobalt hexacarbonyl tert-butylacetylene, CCTBA) as a cobalt precursor because of its high vapor pressure and volatility, a liquid state and its excellent thermal stability under normal conditions. Furthermore, the cobalt film was also deposited at various $H_2/NH_3$ gas ratio(1, 1:1,2,6,8) producing pure cobalt thin films with excellent conformality. Compared to MOCVD cobalt using $H_2$ gas as a reactant, the cobalt thin film deposited by MOCVD using $H_2$ with $NH_3$ showed a low roughness, a low resistivity, and a low carbon impurity. It was found that Co/$TaN_x$ film can achieve a low resistivity of $90{\mu}{\Omega}-cm$, a low root-mean-square roughness of 0.97 nm at a growth temperature of $150^{\circ}C$ and a low carbon impurity of 4~6% carbon concentration.

• Archives of Reconstructive Microsurgery
• /
• v.16 no.2
• /
• pp.113-118
• /
• 2007

Purpose: The purpose of this work was to describe the results of treatment for motor vehiclerelated crushing injuries among children and adolescents under sixteen years in Korea. Materials and Methods: A retrospective analysis was conducted of data from children who were under sixteen year and injured foot by motor vehicles. Cases were documented 1) age at the time of injury, 2) injured site, 3) the area of accident, 4) the kind of vehicle, 5) associated injuries, 6) methods of treatment for soft tissue reconstruction and 7) complications. The relationships between the area of accident and associated injuries, and the kind of vehicle and associated injuries were analyzed using Chi-square test and Fisher exact test. Results: There were 97 children who were 15 year and younger. The mean age was 7.4 years, and 65% were boys. The left foot was more dominant side of injury (57%). Seasonal variation was seen with the number of injuries peaking during the summer (43%, p<0.05). Among the vehicles, 78.3% were the large vehicles (bus, truck or van). The where of accident was more frequent at an alley or less than two lanes of traffic. But, the relationships between the place of accident and associated injury or the kind of vehicles and associated injury were not statistically significant. The associated injury were fracture or dislocation (23 cases, 35.9%), injury of tendon (21 cases, 32.8%). There were amputation or disarticulation of foot in 8 cases (8.2%) and post-traumatic deformities such as flatfoot, hindfoot varus or valus deformities by tendon injury in 7 cases (7.2%). Conclusion: More than 50% of crushing or degloving injuries of child's foot by traffic accidents happened in boys between 5 to 9 years old. The associated injury was unrelated with size of vehicles or accident place at the time of accident. But, even though foot injury happened in an alley or one lane by small vehicles, child who hurt feet by car need thorough investigation about associated injury. If a surgeon keep in mind and treat child to associated injury necessarily, can minimize complication. Microsurgical reconstruction for soft tissue defect was prior to other methods.

• Korean Chemical Engineering Research
• /
• v.55 no.6
• /
• pp.807-815
• /
• 2017

This study investigated the removal efficiency of residual pentane from paclitaxel according to the drying temperature in the case of rotary evaporation, and performed a kinetic and thermodynamic analysis of the drying process. At all the temperatures (25, 30, 35, 40, and $45^{\circ}C$), a large amount of the residual solvent was initially removed during the drying, and the drying efficiency increased when increasing the drying temperature. Five drying models (Newton, Page, modified Page, Henderson and Pabis, Geometric) were then used for the kinetic analysis, where the Henderson and Pabis model showed the highest coefficient of determination ($r^2$) and lowest root mean square deviation (RMSD), indicating that these models were the most suitable. Furthermore, in the thermodynamic analysis of the rotary evaporation, the activation energy ($E_a$) was 4.9815 kJ/mol and the standard Gibbs free energy change (${\Delta}G^0$) was negative, whereas the standard enthalpy change (${\Delta}H^0$) and standard entropy change (${\Delta}S^0$) were both positive, indicating that the drying process was spontaneous, endothermic, and irreversible.

• Korean Journal of Poultry Science
• /
• v.40 no.3
• /
• pp.223-234
• /
• 2013

Poultry industry is abounding day by day as it engrosses less cost of investment per bird as compared to large animals. Poultry have the most copious genomic tool box amongst domestic animals for the detection of quantitative trait loci (QTL) and marker assisted selection (MAS). Use of multiple markers and least square techniques for mapping of QTL affecting quality and production traits in poultry is in vogue. Examples of genetic tests that are available to or used in industry programs are documented and classified into causative mutations (direct markers), linked markers in population-wide linkage disequilibrium (LD) with the QTL (LD markers), and linked markers in population wide equilibrium with the QTL (LE markers). Development of genome-wide SNP assays, role of 42 K, 60 K (Illumina) and 600 K (Affymetrix$^{(R)}$ Axim$^{(R)}$) SNP chip with next generation sequencing for identification of single nucleotide polymorphism (SNP) has been documented. Hybridization based, PCR based, DNA chip and sequencing based are the major segments of DNA markers which help in conducting of MAS in poultry. Economic index-marker assisted selection (EI-MAS) provides platform for simultaneous selection for production traits while giving due weightage to their marginal economic values by calculating predicted breeding value, using information on DNA markers which are normally associated with relevant QTL. Understanding of linkage equilibrium, linkage dis-equilibrium, relation between the markers and gene of interest are quite important for success of MAS. This kind of selection is the most useful tool in enhancing disease resistance by identifying candidate genes to improve the immune response. The application of marker assisted selection in selection procedures would help in improvement of economic traits in poultry.

• Food Science and Preservation
• /
• v.15 no.4
• /
• pp.532-541
• /
• 2008

A central composite design was applied to investigate the effects of the independent variables of NaOH concentration(X1) and extraction time(X2) on dependent variables such as Yield(Y1), Xyl/Ara ratio(Y2), uronic acid(Y3), $\beta$-glucan(Y4) and total sugars(Y5) of hemicelluloses separated from rice bran. The Coefficients of determination(R2) in various models ranged from 0.8626 to 0.9319. Yield increased with increased NaOH concentration and extraction time. The optimum extraction conditions were NaOH concentration at 2.45M and extraction time of 24.2 h. Predicted values at the optimized conditions were acceptable, compared with experimental values. The structural characteristics of an optimum hemicellulose extract were explored. As a result, it showed that the surfaces of hemicellulose had a highly irregular reticulated structure. And also it was both small and large molecular particle in the hemicelluloses. Their average molecular weights were in the ranges $235{\sim}240$ kDa and $8.0{\sim}9.4kDa$, respectively.

• The Journal of the Korea Contents Association
• /
• v.13 no.4
• /
• pp.1-7
• /
• 2013

A personalized recommendation system is a recommendation system that recommends goods to users' taste by using an automated information filtering technology. A collaborative filtering method in this technology is a method that discriminates certain types, which represent similar patterns. Thus, it is possible to estimate the pain strength based on the data of the patients who have the past similar types and extract related conditions according to the similarity in classified patients. A representative method using the Pearson correlation coefficient for extracting the similarity weight may represent inexact results as the sample data is small according to the amount of data. Also, it has a disadvantage that it is not possible to fast draw results due to the increase in calculations as a square scale as the sample data is large. In this paper, the excellency of the intelligence pain nursing intervention u-health system implemented by comparing the scale and similarity group of the sample data for extracting significant data is verified through the evaluation of MAE and Raking scoring. Based on the results of this verification, it is possible to present basic data and guidelines of the pain of patients recognized by nurses and that leads to improve the welfare of patients.

• The Journal of the Korea Contents Association
• /
• v.15 no.2
• /
• pp.363-369
• /
• 2015

Chronic pain is one of the leading causes of hospital visits. It not only affects the patients themselves but also has a major negative impact on their families and society. In this study, we investigated epidemiology of musculoskeletal disorders induced chronic pain among general population based on Korea National Health and Nutrition Examination Survey database and also analysed how it influenced on the use of medical services. This study was done by using the data of 5th Korea National Health and Nutrition Examination Survey (KNHANES V), taking aged 20 years and over adults as research subjects. The EuroQoL-5 Dimension Index(EQ-5D) was used as a survey instrument. T-test, chi-square test and multivariate logistic regression were used for statistical analysis. Subjects with chronic pain had a higher likelihood than control group to use medical services(odds ratio : 5.858, confidence interval 3.636-9.438). Controlling for existence of chronic pain, more women were likely to use medical services than men(1.156, 0.707-1.889). Age, gender and household income level did not affect the use of medical services. Proper control of chronic pain is very helpful in improving patient's quality of life and it also accounts for a large proportion in suppressing excessive consumption of medical services. Anesthesia and pain medicine specialists have superior knowledge about analgesics and anticonvulsants than other physicians do and also have specialized skills to perform procedures like nerve blocks in treating chronic pain. Therefore Anesthesia and pain medicine specialists need to play a leading role in managing chronic pain.