• Journal of the Korean institute of surface engineering
• /
• v.37 no.6
• /
• pp.344-349
• /
• 2004

Emulsions were formed through putting small quantity of nickel electroplating solution into supercritical carbon dioxide, and then electroplating in the $sc-CO_2$ emulsions was conducted. It is an environmental-friendly technology that can solve the treatment of a large quantity of toxic plating wastewater, which is a big problem in the existing wet plating, and also can reduce secondary waste generation fundamentally. Supercritical carbon dioxide emulsions enhanced by ultrasonic horn were formed by non-ionic surfactant and nickel solution. Plating condition within emulsions was set up as 120bar and $55^{\circ}C$ through measurement of electrical conductivity following the pressure change. Experiments were conducted respectively against supercritical carbon dioxide emulsions electroplating and general chemical electroplating, and then their results were compared and analyzed. As the experiment result utilizing emulsions, plating surface was formed very evenly even with a small quantity of electroplating solution, and fine particles were plated compactly without any pinhole or crack due to hydrogenation, which occurs in general electroplating. Used electroplating solution can be reused through recovery process. Therefore, this technology will be able to be applied as new clean technology in electro-plating.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.7
• /
• pp.582-588
• /
• 1995

The preconcentration and determination of trace Cd(Ⅱ), Cu(Ⅱ), Pb(Ⅱ), Mn(Ⅱ) and Zn(Ⅱ) in water samples were studied by the precipitate flotation using La(OH)3 as a coprecipitant. The analytes were quantitatively coprecipitated by adding 3.0 mL of 0.1 M La(Ⅲ) solution in a 1,000 mL water sample and adjusting the pH to 9.5 with NaOH solution. After the addition of the 1:8 mixed surfactant solution of each 0.1% sodium oleate and sodium lauryl sulfate, the solution was stirred with a magnetic stirrer for 10 minutes. The precipitates were floated to the surface by bubbling with nitrogen gas and collected in a small sampling bottle. The precipitates were dissolved in nitric acid and then the solutions were diluted to 25.00 mL with a deionized water. The analytes were determined by flame atomic absorption spectrometry. This procedure was applied to the waste water analysis. This technique was simple, convenient and especially rapid for the analysis of a large volume of sample. And also, from the recoveries of better than 92% which were obtained from real samples, this method could be judged to be applicable to the preconcentration and quantitative determination of trace elements in water samples.

• Membrane and Water Treatment
• /
• v.15 no.3
• /
• pp.117-130
• /
• 2024

The possibility of using lime/mineral solvent solutions has been investigated to effectively remove T-P from wastewater. The lime solvent solution showed an initial T-P removal efficiency of about 90% compared to the less efficient mineral solvent solution removal. High pH and dissolved Ca2+ can form hydroxyapatite minerals (Ca5(PO4)3(OH) or Ca10(PO4)6(OH)2 and can also remove SS and COD from wastewater. Feldspar dissolution solution can be reused twice because the Ca limited sample content provided, but further research is needed to discover other influencing parameters that control the T-P removal efficiency in real wastewater. Because it plays an important role of alkalinity in T-P removal, the success rate is limited. In practical applications, it is obtained according to the pH value wastewater in the environment. The results obtained in this study can highlight new insights on the use of limestone/dissolved mineral solutions to control T-P in wastewater, instead of directly using commercial chemical agents that can produce large amounts of unreacted chemical sludge.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.3
• /
• pp.333-344
• /
• 2013

This paper discussed about the effect of permeability reduction of the jointed rock mass in the vicinity of a tunnel which is one of the reasons making large difference between the estimated ground-water inflow rate and the measured value. Current practice assumes that the jointed rock mass around a tunnel is a homogeneous, isotropic porous medium with constant permeability. However, in actual condition the permeability of a jointed rock mass varies with the change of effective stress condition around a tunnel, and in turn effective stress condition is affected by the ground water flow in the jointed rock mass around the tunnel. In short time after tunnel excavation, large increase of effective tangential stress around a tunnel due to stress concentration and pore-water pressure drop, and consequently large joint closure followed by significant permeability reduction of jointed rock mass in the vicinity of a tunnel takes place. A significant pore-water pressure drop takes place across this ring zone in the vicinity of a tunnel, and the actual pore-water pressure distribution around a tunnel shows large difference from the value estimated by an analytical solution assuming the jointed rock mass around the tunnel as a homogeneous, isotropic medium. This paper presents the analytical solution estimating pore-water pressure distribution and ground-water inflow rate into a tunnel based on the concept of hydro-mechanically coupled behavior of a jointed rock mass and the solution is verified by numerical analysis.

• Journal of KIISE
• /
• v.42 no.2
• /
• pp.242-254
• /
• 2015

In this paper, we address the problem of improving the performance of multi-step k-NN search using multi-dimensional indexes. Due to information loss by lower-dimensional transformations, existing multi-step k-NN search solutions produce a large tolerance (i.e., a large search range), and thus, incur a large number of candidates, which are retrieved by a range query. Those many candidates lead to overwhelming I/O and CPU overheads in the postprocessing step. To overcome this problem, we propose two efficient solutions that improve the search performance by reducing the tolerance of a range query, and accordingly, reducing the number of candidates. First, we propose a tolerance reduction-based (approximate) solution that forcibly decreases the tolerance, which is determined by a k-NN query on the index, by the average ratio of high- and low-dimensional distances. Second, we propose a coefficient control-based (exact) solution that uses c k instead of k in a k-NN query to obtain a tigher tolerance and performs a range query using this tigher tolerance. Experimental results show that the proposed solutions significantly reduce the number of candidates, and accordingly, improve the search performance in comparison with the existing multi-step k-NN solution.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.12
• /
• pp.1775-1780
• /
• 2003

A continuous flow system has been developed to determine trace Cu(II), Mn(II), Ni(II) and Zn(II) in a large volume of water samples by a solvent sublation technique. The mixed solution of 1,10-phenanthroline(phen) and thiocyanate ion was used as ligands for the formation of their ternary complexes. The continuous system was constructed in this laboratory with a peristaltic pump, a mini shaker, three mixing bottles and a flotation cell by connecting each part with a polyethylene tube. The flotation conditions such as the flow rate of sample solution and the injection rates of ligand, buffer and surfactant solutions have been investigated to obtain the best sublation efficiencies. Each solution flowed into the flotation cell through each polyethylene tube by the peristaltic pumps. The ternary complexes were floated and extracted into MIBK in a flotation cell of 2 L by bubbling a nitrogen gas. The absorbances of extracted analytes in MIBK were directly measured by graphite furnace-AAS. The concentrations of 1,10-phenanthroline and thiocyanate ion were $2.6\;{\times}\;10^{-3}$ M and $2.3\;{\times}\;10^{-2}$ M in the mixed solution, respectively. The pH of sample solution was adjusted to 5.0 with a buffer solution and 1%(m/v) sodium lauryl sulphate solution was added as a surfactant to support the effective flotation of the complexes. The $N_2$ gas was bubbled at 30 mL/min for 90 minutes for 20 L of sample. Reproducible results of less than 10% RSD and recoveries of 80-120% could be obtained in real samples.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.369-369
• /
• 2016

A nanostructure composite is a highly suitable substance for photoacoustic ultrasound generation. This allows an input laser beam (typically, nanosecond pulse duration) to be efficiently converted to an ultrasonic output with tens-of-MHz frequency. This type of energy converter has been demonstrated by using a carbon nanotube (CNT)-polydimethylsiloxane (PDMS) composite film that exhibit high optical absorption, rapid heat transition, and mechanical durability, all of which are necessary properties for high-amplitude ultrasound generation. In order to develop the CNT-PDMS composite film, a high-temperature chemical vapor deposition (HTCVD) method has been commonly used so far to grow CNT and then produce a CNT-PDMS composite structure. Here, instead of the complex HTCVD, we use a mixed solution of hydrophobic multi-walled CNT and dimethylformamid (DMF) and fabricate a solution-processed CNT-PDMS composite film over a spherically concave substrate, i.e. a focal energy converter. As the solution process can be applied over a large area, we could easily fabricate the focal transmitter that focuses the photoacoustic output at the moment of generation from the CNT-PDMS composite layer. With this method, we developed photoacoustic energy converters with a large diameter (>25 mm) and a long focal length (several cm). The lens performance was characterized in terms of output pressure amplitude for an incident pulsed laser energy and focal spot dimension in both lateral and axial. Due to the long focal length, we expect that the new lens can be applied for long-range ultrasonic treatment, e.g. biomedical therapy.

• Journal of Computing Science and Engineering
• /
• v.2 no.3
• /
• pp.249-273
• /
• 2008

Epidemic protocols have two fundamental assumptions. One is the availability of a mechanism that provides each node with a set of log(N) (fanout) nodes to gossip with at each cycle. The other is that the network size N is known to all member nodes. While it may be trivial to support these assumptions in small systems, it is a challenge to realize them in large open dynamic systems, such as peer-to-peer (P2P) systems. Technically, since the most fundamental parameter of epidemic protocols is log(N), without knowing the system size, the protocols will be limited. Further, since the network churn, frequently observed in P2P systems, causes rapid membership changes, providing a different set of log(N) at each cycle is a difficult problem. In order to support the assumptions, the fanout nodes should be selected randomly and uniformly from the entire membership. This paper investigates one possible solution which addresses both problems; providing at each cycle a different set of log(N) nodes selected randomly and uniformly from the entire network under churn, and estimating the dynamic network size in the number of nodes. This solution improves the previously developed distributed algorithm called Shuffle to deal with churn, and utilizes the Shuffle infrastructure to estimate the dynamic network size. The effectiveness of the proposed solution is evaluated by simulation. According to the simulation results, the proposed algorithms successfully handle network churn in providing random log(N0 fanout nodes, and practically and accurately estimate the network size. Overall, this work provides insights in designing epidemic protocols for large scale open dynamic systems, where the protocols behave autonomically.

• Macromolecular Research
• /
• v.15 no.6
• /
• pp.498-505
• /
• 2007

This study demonstrated the in-situ functionalization with polymers of multi-walled carbon nanotubes (MWNTs) via emulsion polymerization. Polystyrene-functionalized MWNTs were prepared in an aqueous solution containing styrene monomer, non-ionic surfactant and a cationic coupling agent ([2-(methacryloyloxy)ethyl]trime-thylammonium chloride (MATMAC)). This process produced an interesting morphology in which the MWNTs, consisting of bead-string shapes or MWNTs embedded in the beads, when polymer beads were sufficiently large, produced nanohybrid material. This morphology was attributed to the interaction between the cationic coupling agent and the nanotube surface which induced polymerization within the hemimicellar or hemicylindrical structures of surfactant micelles on the surface of the nanotubes. In a solution containing MATMAC alone without surfactant, carbon nanotubes (CNTs) were not well-dispersed, and in a solution containing only surfactant without MATMAC, polymeric beads were synthesized in isolation from CNTs and continued to exist separately. The incorporation of MATMAC and surfactant together enabled large amounts of CNTs (> 0.05 wt%) to be well-dispersed in water and very effectively encapsulated by polymer chains. This method could be applied to other well-dispersed CNT solutions containing amphiphilic molecules, regardless of the type (i.e., anionic, cationic or nonionic). In this way, the solubility and dispersion of nanotubes could be increased in a solvent or polymer matrix. By enhancing the interfacial adhesion, this method might also contribute to the improved dispersion of nanotubes in a polymer matrix and thus the creation of superior polymer nanocomposites.

• The Korean Journal of Physiology
• /
• v.13 no.1_2
• /
• pp.41-50
• /
• 1979

The activation mechanism of K-induced contracture was studied in renal vascular muscle which does not generate an action potential readily and in taenia coli which generates a spike potential spontaneously. Helical strips of arterial muscle from rabbit renal arteries and longitudinal strips of taenia coli from guinea-pig's colons, respectively, were prepared. All experiments were performed in Tris-buffered Tyrode solution which was aerated with 100% $O_2$ and kept $35^{\circ}C$. Renal arterial muscles developed the contracture rapidly, which was composed of a small phasic and a large tonic components, when exposed to a 40 mM K-Tyrode solution. In the absence of external $Ca^{++}$, however, no K-contracture appeared. The contracture induced by K-depolarization was abolished by the treatment with verapamil, which is known to be a selective $Ca^{++}-blocker$ through potential-sensitive $Ca^{++}-channel$. K-contracture of taenia coli showed the contracture composed of a large phasic and a small tonic components. In the $Ca^{++}-free$ Tyrode solution, only the tonic component was abolished and almost no change in the phasic component was observed. The amplitude of tonic component was dependent on the external $Ca^{++}$; The tonic component increased dose-dependently by a stepwise increase of the external $Ca^{++}$, and this component decreased in parallel with the increase of verapamil in the external medium. The results of this experiment suggest that K-contracture of rabbit renal artery is the direct result of the influx of the external $Ca^{++}$, while that of taenia coli is the result of both $Ca^{++}$ influx and the release of sequestered $Ca^{++}$.