• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.5
• /
• pp.374-380
• /
• 2011

In this paper a printing process for patterning electrodes on large area substrate was developed by combining screen printing with reverse off-set printing. Ag ink was uniformly coated by screen printing. And then etching resist (ER) was patterned in the Ag film by reverse off-set printing, and then the non-desired Ag film was etched off by etchant. Finally, the ER was stripped-off to obtain the final Ag patterns. We extracted the suitable conditions of reverse Using the process we successfully fabricated gate electrodes and scan bus lines of OTFT-backplane used for e-paper, in which the diagonal size was 6 inch, the resolution $320{\times}240$, the minimum line width 30 um, and sheet resistance 1 ${\Omega}/{\Box}$.

• Journal of information and communication convergence engineering
• /
• v.13 no.3
• /
• pp.189-196
• /
• 2015

In this paper, we present a rotating auto-zeroing offset cancellation technique, which can improve the performance of touch screen sensing circuits. Our target touch screen detection method employs multiple continuous sine waves to achieve a high speed for large touch screens. While conventional auto-zeroing schemes cannot handle such continuous signals properly, the proposed scheme does not suffer from switching noise and provides effective offset cancellation for continuous signals. Experimental results show that the proposed technique improves the signal-to-noise ratio by 14 dB compared to a conventional offset cancellation scheme. For the realistic simulation results, we used Cadence SPECTRE with an accurate TSP model and noise source. We also applied an asymmetric device size (10% MOS size mismatch) to the OP Amp design in order to measure the effectiveness of offset cancellation. We implemented the proposed circuit as part of a touch screen controller system-on-chip by using a Magnachip/SK Hynix 0.18-µm complementary metal-oxide semiconductor (CMOS) process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.896-898
• /
• 2009

The printed electrodes of organic thin-film transistors (OTFTs) were fabricated by screen printing using nanoparticle silver pastes. The screen printed OTFT corresponds to channel lengths between 7.6 to 82.6 ${\mu}m$ (designed L=10 to 80 ${\mu}m$) on the $150{\times}150mm^2$ paper. The channel length deviations for 40 to 80 ${\mu}m$ patterns were less than 5 %. However, the channel lengths for 10 to 30 ${\mu}m$ patterns were increased by 20 %. The screen printed bis(triisopropyl-silylethynyl) pentacene (TIPS-pentacene) OTFTs obtained had a field-effect mobility as large as 0.08 (${\pm}0.02$) $cm^2$/Vs, an on/off current ratio of $10^5$ and a subthreshold slope of 1.95 V/decade.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.4
• /
• pp.71-79
• /
• 2015

This paper proposes a new touch screen sensing method that improves the drawback of conventional single-line sensing methods for mutual capacitance touch screen panels (TSPs). It introduces a dual sensing and voltage shifting method, which reduces the ambient noise effectively and enhances the touch signal strength. The dual sensing scheme reduces the detection time by doubling the integration speed using both edges of excitation pulse signals. The voltage shifting method enhances the signal-to-noise ratio (SNR) by increasing the voltage range of integrations, and maximizing the ADC's input dynamic range. Simulation and experimental results using a commercial 23" large touch screen show an SNR performance of 43dB and a scan rate 2 times faster than conventional schemes - key properties suited for a large touch screen panels. We implemented the proposed method into a TSP controller chip using Magnachip's CMOS 0.18um process.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.48 no.3
• /
• pp.1-12
• /
• 2011

Large-sized multi-touch screen is usually made using infrared rays. That is because it has technical constraints or cost problems to make the screen with the other ways using such as existing resistive overlays, capacitive overlay, or acoustic wave. Using infrared rays to make multi-touch screen is easy, but is likely to have technical limits to be implemented. To make up for these technical problems, two other methods were suggested through Surface project, which is a next generation user-interface concept of Microsoft. One is Frustrated Total Internal Reflection (FTIR) which uses infrared cameras, the other is Diffuse Illumination (DI). FTIR and DI are easy to be implemented in large screens and are not influenced by the number of touch points. Although FTIR method has an advantage in detecting touch-points, it also has lots of disadvantages such as screen size limit, quality of the materials, the module for infrared LED arrays, and high consuming power. On the other hand, DI method has difficulty in detecting touch-points because of it's structural problems but makes it possible to solve the problem of FTIR. In this thesis, we study the algorithms for effectively correcting the distort phenomenon of optical lens, and image processing algorithms in order to solve the touch detecting problem of the original DI method. Moreover, we suggest calibration algorithms for improving the accuracy of multi-touch, and a new tracking technique for accurate movement and gesture of the touch device. To verify our approaches, we implemented a table-based multi touch screen.

• ETRI Journal
• /
• v.35 no.5
• /
• pp.900-910
• /
• 2013

Small-screen mobile terminals have difficulty accessing existing Web resources designed for large-screen devices. This paper presents an adaptive transformation method based on webpage semantic features to solve this problem. According to the text density and link density features of the webpages, the webpages are divided into two types: index and content. Our method uses an index-based webpage transformation algorithm and a content-based webpage transformation algorithm. Experiment results demonstrate that our adaptive transformation method is not dependent on specific software and webpage templates, and it is capable of enhancing Web content adaptation on small-screen terminals.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.751-754
• /
• 2004

Nowadays a large number of PLCs are being used in automatic machines for factory automation in industry, and HMI is essential for the effective and convenient operation of PLCs. Each screen displayed in actual EMI equipment should be created, modified and deleted using a PC-based editor and it should be composed of necessary display components to express desired OUI. Based object-oriented development methodology, this study designed screen objects representing a editing screen, display components forming the UI of screens and data management objects necessary for data exchange with HIM system and, based on the objects, implemented a HMI screen editor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.4
• /
• pp.367-372
• /
• 2006

A carbon nanotube field emission display(CNT FED) panel with a 2 inch diagonal size was fabricated using a screen printing of a prepared photo-sensitive CNT paste and vacuum in-line sealing technology. After a surface treatment of the patterned CNT, only the carbon nanotube tips are uniformly exposed on the surface. The diameter of the exposed CNTs are usually about 20 nm. Using the photo-sensitive CNT paste, we have developed a triode type CNT FEA with a self-aligned gate-emitter structure. The turn on voltage was around 100 V which corresponds to according the turn on field of about $40V/{\mu}m$. By the creation of a self-aligned gate-emitter structure, it is expected that the screen printed photo-sensitive CNT paste is promising as a good candidate for the large size field emission display.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.48-53
• /
• 2001

This experimental study is to research heat transfer characteristics in copper-water heat pipes with screen wick, the 150 and 200-mesh. Recent advances in the miniaturization and large capacity of electronic devices have had a major impact on the design of electronic equipment. As a result, a high-performance cooling system is needed. Experimental variables are inclination angle, number of layer and temperature of cooling water. The distilled water was used for the working fluid. At a inclination angle $6^{\circ}$, the 200-mesh screen wick 3-layer is shown the best heat transfer performance.

• Journal of Korea Multimedia Society
• /
• v.20 no.11
• /
• pp.1803-1810
• /
• 2017

A large amount of processing time is required if the process of detecting the touch position on the touch screen and displaying it on the display panel is performed only by software. In this paper, we propose a method to output information touched on the screen using H/W method in order to improve the response speed delay. In the FPGA module designed for the HDMI signal output to the display module, the touch information is input to the serial data signal including touch coordinate information, point size, and color information. Then the module render the image using HDMI signal input to the module and the touch information. This method has a pipeline structure so it has effect of reducing the delay time that occurs in outputting the touch information compared with the conventional software processing method.