• Journal of the Korean Applied Science and Technology
• /
• v.25 no.2
• /
• pp.205-210
• /
• 2008

The transformation of the liquid crystal complex made by binding of anionic surfactant, sodium dodecyl sulfate (SDS), into high charge density cationic polymer, the homopolymer of diallyldimethylammonium chloride (PDADMAC) was induced by adding of nonionic surfactants and investigated by means of microscopy and FE.SEM. Among nonionic surfactants in this experiments polyethylene glycol (3 mol) ether of lauryl alcohol (laureth-3) made variation in the complex. The laureth-3 transformed the complex into spherulite vesicle with the size of ca.$100{\mu}m$. This change increased the viscosity and the turbidity of the solution phase separated originally. Microscope showed that they are spherulite particles and polarized microscope suggested they are multi.lamellar liquid crystals. FE-SEM also proved that explicitly.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.4
• /
• pp.379-384
• /
• 1997

High quality MCM-41 is prepared from a gel of molar composition SiO2:0.20 CTACl:0.18 TMAOH:25 H2O aged at 20 ℃ for 24 hours before crystallization lasting for 48 hours. The (110) and (200) peaks of XRD pattern of high quality MCM-41 are unusually well resolved and the FWHM (full-width-at-half-maximum) of the (100) peak is 0.13° for as-prepared MCM-41 and 0.21° for calcined one, which indicate well-developed crystals. The properties of the crystal depend on the source and concentration of the reactants and the gel aging time. There is no induction period in the course of the synthesis, which is conveniently monitored by pH measurement. Gel aging, during which a spatial distribution of silicate polyanions and micellar cations is established, is essential for preparing high quality MCM-41. Surfactants with the same cationic organic group but different counteranions change the crystallization behavior. Highly basic gel (pH=12.6) favours the lamellar product; the quality of MCM-41 is lower as insufficient TMAOH is available to dissolve the silica.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.48 no.5
• /
• pp.315-317
• /
• 2022

Osseous metaplasia is defined as the formation of lamellar bone inside soft tissue structures where bone normally does not exist. It results from the transformation of non-osseous connective tissue into mature bone. This condition is rare in the oral and maxillofacial region. We report a case of osseous metaplasia of the maxilla, a rare benign tumor in an uncommon region. A 60-year-old male patient visited our clinic complaining of foreign body sensation and asymptomatic swelling on the right palatal side. However, he did not experience pain and reported no local trauma that he could remember. Intra-oral examination revealed an exophytic lesion on the right palatal portion. On computed tomography, there was a round hard-tissue mass approximately 2 cm in diameter on the right palate area. The mass was biopsied and diagnosed as an osseous metaplasia. We review the clinical, radiographic, and histologic features and common causes of osseous metaplasia and report a rare case of osseous metaplasia of the palate.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.30 no.2
• /
• pp.159-165
• /
• 2004

This study described about method that forms liquid crystal gel (LCG) by main ingredient with hydrogenated lechin (HL) in O/W emulsion system. Result of stability test is as following with most suitable LCG's composition. Composition of LCG is as following, to form liquid crystal, an emulsifier used 4.0wt% of cetostearyl alcohol (CA) by 4.0wt% of HL as a booster. Moisturizers contained 2wt% of glycerin and 3.0wt% of 1,3-butylene glycol (1,3-BG). Suitable emollients used 3.0wt% of cyclomethicone, 3.0wt% of isononyl isononanoate (ININ), 3.0wt% of cerpric/carprylic triglycerides (CCTG), 3.0wt% of macademia nut oil (MNO) in liquid crystal gel formation. On optimum conditions of LCG formation, the pHs were formed all well under acidity or alkalinity conditions (pH=4.0-11.0). Considering safety of skin, pH was the most suitable 6.0${\pm}$1.0 ranges. The stable hardness of LCG formation appeared best in 32 dyne/$\textrm{cm}^2$. Particle of LCG is forming size of 1-20$\mu\textrm{m}$ range, and confirmed that the most excellent LCG is formed in 1-6$\mu\textrm{m}$ range. According to result that observe shape of LCG with optical or polarization microscope, LCG could was formed, and confirmed that is forming multi -layer lamellar type structure around the LCG. Moisturizing effect measured clinical test about 20 volunteers. As a result, moisturizing effect of LCG compares to placebo cream was increased 36.6%. This could predicted that polyol group is appeared the actual state because is adsorbed much to round liquid crystal droplets to multi-lamellar layer's hydrophilic group. It could predicted that polyol group is vast quantity present phase that appear mixed because is adsorbed to round liquid crystal to multi-lamellar layer's hydrophilic group. This LCG formation theory may contribute greatly in cosmetics and pharmacy industry development.

• Journal of the Korean Chemical Society
• /
• v.44 no.1
• /
• pp.52-59
• /
• 2000

The reaction gel mixtures of molar composition (0.3${\sim}$2.1) $SiO_2:\;(0.10{\sim}0.50)\;CTABr:\;0.15{\sim}0.23)\;TMAOH:\;(20{\sim}100)\;H_2O$ we prepared and then aged at room temperature for a definite duration. The aged gel is reacted hydrothermally at $150^{\circ}C$ for 2 days. The pH of reaction gel during synthesis is strongly influenced by the concentration of TMAOH and silica source. The pH change affects the phase of product, which is monitored by X-ray diffractometer. With increasing the TMAOH ratio from 0.19 to 0.23, the gel becomes more basic, and the product involves more lamellar phase. At TMAOH ratio lower than 0.19, the hexagonal phase is lower with decrease of pH. The content of the lamellar phase increases at a lower $SiO_2$ concentration, and higher concentrations have a clear detrimental effect on the crystallinity ofMCM-41 due to an excess silica source. The best quality MCM-41 is synthesized from a reaction gel composition of $1.0\;SiO_2:\;0.27\;CTABr:\;0.19\;TMAOH:\;40\;H_2O$. The pH values of this gel, aged one for 24 hr, and reacted one at $150^{\circ}C$ for 2 days are 12.3, 11.5, and 10.5, respectively. Gel aging for 24 h is essential for preparing high quality MCM-41. Longer aging causes a decrease of hexagonal phase.

• Korean Journal of Materials Research
• /
• v.28 no.3
• /
• pp.174-181
• /
• 2018

Three kinds of STS304-Zr alloys were fabricated by varying the Zr content, and their microstructure and fracture properties were analyzed. Moreover, we performed heat treatment to improve their properties and studied their microstructure and fracture properties. The microstructure of the STS304-Zr alloys before and after the heat treatment process consisted of ${\alpha}-Fe$ and intermetallics: Zr(Cr, Ni, Fe)2 and Zr6Fe23. The volume fraction of the intermetallics increased with an increasing Zr content. The 11Zr specimen exhibited the lowest hardness and fine dimples and cleavage facets in a fractured surface. The 15Zr specimen had high hardness and fine cleavage facets. The 19Zr specimen had the highest hardness and large cleavage facets. After the heat treatment process, the intermetallics were spheroidized and their volume fraction increased. In addition, the specimens after the heat treatment process, the Laves phase (Zr(Cr, Ni, Fe) 2) decreased, the Zr6Fe23 phase increased and the Ni concentration in the intermetallics decreased. The hardness of all the specimens after the heat treatment process decreased because of the dislocations and residual stresses in ${\alpha}-Fe$, and the fine lamellar shaped eutectic microstructures changed into large ${\alpha}-Fe$ and spheroidized intermetallics. The cleavage facet size increased because of the decomposition of the fine lamellar-shaped eutectic microstructures and the increase in spheroidized intermetallics.

• Applied Chemistry for Engineering
• /
• v.8 no.3
• /
• pp.473-481
• /
• 1997

Enhanced videomicroscopy was used to observe the dynamic behavior which occurred when water containing pure nonionic surfactant was carefully contacted with equal volumes of polar oils such as oleyl alcohol and oleic acid at various temperatures. A key component of the system is a vertical-stage microscope which provides for stable interfaces by locating the oil above the denser aqueous phase. This arrangement allowed intermediate phases formed at the surface of contact to be clearly observed, as well as any spontaneous emulsification which developed. Contacting experiments with $C_{12}E_5$ as the surfactant and with pure oleyl alcohol and oleic acid soils showed little activity below the cloud point but vigorous activity at higher temperatures including formation of an intermediate lamellar liquid crystalline phase. Diffusion path theory, which allows prediction of spontaneous emulsification resulting from diffusion and of intermediate phase formation during contacting processes, was used to understand the dynamic behavior seen during contacting experiments. Tentative diffusion paths for the contacting experiments with pure oleyl alcohol were presented with the aid of a partial phase diagram of the oleyl alcohol-water-$C_{12}E_5$ system.

• Journal of Periodontal and Implant Science
• /
• v.33 no.1
• /
• pp.91-102
• /
• 2003

Several effective treatment methods and materials have been developed for the treatment of furcation involvement. Currently, the combination of guided tissue regeneration (GTR) and bone grafts is the most commonly prescribed method of treating furcation involved defects. But because these cases often present with poor accessibility, placement of the membrane may be difficult and consequently, clinically impractical. In this study, the alveolar bone healing patterns of adult beagle dogs presenting with alveolar bone destruction treated by one of two methods - treatment using solely bone allografts (BBP(R)), or treatment using bone allografts (BBP(R)) stabilized by a fibrin adhesive - were comp ared. The effects of the fibrin adhesive on the initial stabilization of the newly formed bone, subsequent regeneration of bone, and the feasibility of the clinical application of the fibrin adhesive were analyzed. The results of the study were as follows: 1. Clinical signs of inflammation at the 4-8 week interval were not observed: but signs of mild inflammation were histologically observed at the 4-week interval. 2. Allografts stabilized by fibrin adhesive showed good bone formation, whereas defects treated with only the allograft material showed incomplete alveolar bone regeneration. 3. Allografts stabilized by fibrin adhesive showed a decrease in the amount old bone with a concurrent increase in the formation of new lamellar bone four weeks post-op, whereas defects treated with only the allograft material showed no new lamellar bone formation at the same interval. 4. In detects treated with only the allograft material, the defective area was filled with connective tissue 8-weeks post-op, whereas fibrin adhesive stabilized allografts showed viable connections between the original bone and the newly formed bone, in addition to neovascularization 8-weeks post-op. The results of this study show that concurrent use of fibrin adhesive materials can stabilize the allograft material and aid in new bone formation Although the stability of fibrin adhesives fall short of the results achievable by GTR membranes, in cases presenting with poor accessibility that contraindicate the use of membranes, fibrin adhesive materials provide a viable and effective alternative to graft stabilization and new bone formation.

• Applied Microscopy
• /
• v.38 no.3
• /
• pp.195-204
• /
• 2008

This study was intended to identify the effectiveness of Lithospermum erythrorhizon in the UVB-irradiated mouse skin. The C57BL mice were divided into three groups; the control group, the UVB irradiated group(UVB group), and the group treated with Lithospermum erythrorhizon extracts after UVB irradiation(UVB+Le group). 10 mouses were collected and sacrificed at 24 hrs, 48 hrs, 72 hrs, 120 hrs, and 168 hrs, respectively. In the result, the transepidermal water loss (TEWL) was decreased the UVB+Le group than UVB groups by time. At the 168 hrs group was significantly lower(p<0.05). In the result, the melanin value was decreased in the UVB+Le group than UVB group, but meaningless(p>0.05). In the result of erythema index, the UVB+Le group was meaningfully lower at 24 hrs, 48 hrs, and 72 hrs group than UVB group(p<0.05). In the result of scanning electron micrograph observation, the UVB+Le group was allevited swelling than UVB group at the 24 hrs, formation of the scab at the 48 hrs, regular plate shap at the 72 hrs, new keratin observated at the 120 hrs partially, and fine fiber covered epidermis surface at the 168 hrs. In the result of transmission electron micrograph observation, the UVB+Le group was facilitation of increased lamellar bodies and reformation lamellar bodies than UVB group at the all groups. Almost all the structures were recovered at the 160 hrs group. In conclusion, Lithospermum erythrorhizon extracts may recovery on the UVB-irradiated mouse skin.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.79-79
• /
• 2010

저온용 무연 솔더의 대표 조성으로 고려되고 있는 Sn-58Bi(융점: $138^{\circ}C$) 공정(eutectic) 조성은 우수한 강도에도 불구하고 연성(ductility) 측면에서의 문제점이 지속적으로 보고되고 있다. 따라서 이 합금계의 연성을 최대로 개선시킬 수 있으면서도 실제 상용화가 가능한 합금 조성의 개발 연구가 요청된다. 본 연구에서는 Sn-Bi 2원계 조성에서 최대의 연성을 나타내는 것으로 보고된 Sn-40Bi 조성에 미량의 합금원소를 첨가함으로써 최대의 연성을 확보하는 한편, 그 연성 특성이 변형속도에 어느 정도 민감한지를 인장 실험을 통해 결정하고자 하였다. 합금원소로는 0.1~0.5 wt%의 Ag, Mn, In, Cu를 선택하였으며, 인장 시편을 제조하여 $10^{-2}$, $10^{-3}$, $10^{-4}\;s^{-1}$의 3종류로 변형속도를 변형시켜가며 응력-변형 곡선(stress-strain curve)을 측정하였고, 조성별, 변형속도별로 최대인장강도(ultimate tensile stress, UTS) 및 연신율 결과들을 정리하였다. 합금원소를 첨가한 조성의 경우는 모든 시험 조건에서 Sn-40Bi보다 우수한 연신률을 나타내는 것으로 측정되었으나, $10^{-2}\;s^{-1}$의 빠른 변형속도에서는 그 향상 정도가 상대적으로 감소하는 경향이 관찰되었다. 특히 Sn-40Bi-0.5Ag 조성의 경우 느린 변형속도에서 특히 눈에 띄는 연신률 값을 나타내며, 모든 변형속도 조건에서 가장 우수한 연성을 나타내었다. 한편 Sn-40Bi-0.1Cu 조성의 경우 변형속도에 따른 연신률의 변화 정도, 즉, 변형속도에 따른 연신률의 민감도가 매우 커 $10^{-4}\;s^{-1}$ 속도에서는 Sn-40Bi-0.5Ag에 버금가는 연신률 값이 측정되었으나, $10^{-2}\;s^{-1}$ 속도에서는 가장 나쁜 연신률 특성을 보여주었다. Sn-40Bi-0.2Mn 조성은 최고의 연신률 향상 특성을 나타내지는 않았으나, In을 첨가한 경우보다는 대체적으로 우수한 연성을 나타내었다. 이상의 각 합금별 연성 특성은 인장시험 전의 미세조직 관찰 결과와 인장시험 후 파면부의 조직변화 관찰 결과로부터 해석되었다. 그 결과 석출상의 형성 여부, 인장 시험 중 재결정 조직의 형성 여부, 라멜라(lamellar) 조직의 분율과 라멜라 간격(lamellar spacing)의 정도 또는 $\beta$-Sn과 라멜라 조직 사이의 결정립계와 라멜라 조직 내 결정립계에서의 슬라이딩 모드(sliding mode) 변형 정도, 석출상의 크기와 분포 정도 등이 연신률 및 변형속도 민감도와 같은 연성 특성에 가장 큰 영향을 미치는 인자인 것으로 분석되었다.