• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.53-59
• /
• 2009

In multi-user MIMO systems, a base station transmits multiple data to multi-user simultaneously in order to improve performance and bandwidth efficiency. When the base station transmits multiple data to multi-user simultaneously, multi-user interference occurs severely. In this paper, we define a post-processing leakage as the total power leaked from desired user to all other users after combining at the output of each user. Using concept of the post-processing leakage, we also define a performance metric, the so called signal-to-post-processing-leakage-plus-noise ratio (SPPLNR). Assuming that the receiver is the minimum mean square error (MMSE) receiver, we propose an iterative SPPLNR-based beamforming that determines beamforming vectors and combining vectors by using an iterative method. The proposed scheme does not impose a condition on the relation between the number of transmit antennas for the base station and the number of receive antennas for users. Simulation results show that the proposed scheme outperforms a beamforming scheme perfectly eliminating the multi-user interference when channel estimation error exists.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.12
• /
• pp.1093-1098
• /
• 2007

Tilting trains are currently in operation in 13 countries around the world. With the advances in tilting technology, verification of economic efficiency, and changes in economic situations, the introduction of tilting trains will rapidly spread across the globe. The measurement system is composed of the industrial computers installed in the console and the measurement racks mounted on each car. It is utilized to accumulate the data by the communication card and the optical cable. The optical cable and power cable are coupled at the connector located in joint of train to make easy to disconnect car each other. The signal conditioner is designed to choose and to extend the channel for each sensor readily. The sensor measurement rack has adopted as decentralization method. It is installed in each car to minimize the cable length. In also, it is manufactured based on 19"rack and covered to protect the cable. In this study, the programs for measurement and analysis were also developed to understand the traction system characteristics of TTX. Using this measurement system, we studied that acceleration test, re-powering test, and gradually powering test. The acceleration performance of TTX is 1.735 km/h/s, and it is inner standard value. The notch test result from 1 to 7 steps, DC link voltage is under standard value, and the output electric current of inverter is controlled normally. From the test results, we saw the performances of the traction systems are normal.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.3
• /
• pp.253-263
• /
• 2008

Extension of IFC data model for steel bridge members is proposed to represent detailed design information. First of all, the design data items and their representation method are classified by analyzing primary references such as design specification, structural calculation documents and shop drawings. Some of the classified items are enough to be represented by the existing IFC model. However, the need of additional model is noted to systematically represent the design information for other items such as stiffener, diaphragm, joint system, and shear connector. An inheritance relations and properties for added model are also defined. The application program based on the proposed data model is developed. In the end, by loading the application program on the AutoCAD 2002 program, end-users can input the design information of steel bridge members. The applicability and efficiency of the proposed data model and the program are verified by checking the section area, intervals, and interferences.

• Korean Journal of Community Nutrition
• /
• v.17 no.2
• /
• pp.194-204
• /
• 2012

The purpose of this study was to investigate school dietitians' satisfaction with and needs for School Meal Service Support Centers. A web-based on-line survey was conducted with 1,102 nutrition teachers or school dietitians using four School Meal Service Support Centers during the summer of 2011. The data from 578 respondents (52.5%), consisting of 165 (44.4%), 334 (53.4%), 41 (67.2%), and 38 (86.4%) dietitians using Seoul, Gyeonggi, Suncheon and Gyeongju centers, respectively, were analyzed. The main reason for using the centers was subsidies from local governments. The dietitians using the metropolitan centers, which were Seoul and Gyeonggi centers, tended to buy agricultural products through the centers only, and those using local centers, which were Suncehon and Gyeongju centers, bought those products from the private suppliers as well as from the centers. The dietitians' overall level of satisfaction with the centers was not high showing 3.3 out of 5 points; it was significantly associated with the operating system and services of the centers such as system efficiency, delivery accuracy, communication, and information provision rather than the agricultural products provided by the centers. The dietitians preferred joint operation of the centers by local governments and producers' groups. They wanted School Meal Service Support Centers to be evaluated every year. It was suggested that efforts should be made to improve the operation system and service of School Meal Service Support Centers for improving dietitians' satisfaction with the centers. In addition, an evaluation system for School Meal Service Support Centers should be implemented soon based on school dietitians' needs.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.1 s.23
• /
• pp.71-78
• /
• 2007

Stainless steel is very famous for using of industrials structure and joint elements. Stainless steel wire drawing is one of the most ancient crafts. But there's not any standard size of tapered die during tile drawing. This paper was studied die angle and dimension of whole die by using AFDEX drawing simulator. Stress, metal flow and strain rate was analyzed by AFDEX tools during the wire drawing. So optimum data of during dies was taken from them. Simulation data was correspond with experimental data. The results of the optimum dies are shown that (1) Reduction angle is $13.8^{\circ}$ (2) Bark relief angle is $20^{\circ}$ (3) Bearing length is 0.7975mm (4) Bearing dia is 0.2393mm The research of the optimum result when the make dies is connected an enterprise. After researching, I hope that indirection effect creation make development situation of the manufactural technical, practical application of the other die size by the detail data, utility factor and economical efficiency.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.27 no.2
• /
• pp.223-231
• /
• 2011

The purpose of this case report is to introduce new attachment system(milled titanium bar with $Locator^{(R)}$ attachment) for implant supported overdenture in maxillary edentulous patients. A 56-years-old male patient visited the hospital due to the mobility of his maxillary fixed partial dentures(10-unit bridge). Including temporomandibular joint(TMJ), there was no specific PMHs to influence dental treatment. In radiographic and clinical evaluation, there was a severe bone resorption and mobility in maxillary teeth. Accordingly all the remaining maxillary teeth was extracted and fabrication of implant supported overdenture was planned. The milled titanium bar with $Locator^{(R)}$ was designed as an attachment system, considering the stability and retention of denture, masticatory efficiency, oral hygiene care, esthetics, pronunciation, and patient's financial state. The milled titanium bar was manufactured using CAD/CAM technology, and $Locator^{(R)}$ attachment connected to the bar by tap & drill method. For over 1-year, in terms of function and esthetics, satisfactory result was obtained.

• Hwankyungkyoyuk
• /
• v.23 no.2
• /
• pp.46-64
• /
• 2010

The purpose of this study is to analyze how the contents of education for sustainable development are reflected in the middle school environment curriculum revised in 2007, and to propose how to integrate content for improving sustainable development education. For this, I analyzed the 2007 Revised Environment Curriculum for Middle Schools by using social network analysis which is the useful methodology to understand the relations of contents. Social Network analysis is a useful tool to excavate the forms of structure or relationship and to explain the characteristics of the system that arise through relationships or to explain the units composing the system. When sustainable development education was examined from 3 points of view, it included environmental sustainability, economical sustainability, and social sustainability. I used the 2007 Revised Environment Curriculum for Middle Schools and manual of curriculum for analysis. The results are 1) The biodiversity conservation and energy efficiency have taken most important positions. 2) In case of economical sustainability pillar, sustainable production had been emphasized. 3) In the case of the social sustainability pillar, health improvement are considered significant. 4) The efforts of trying to approach sustainable development education as an integrated curriculum is week. Integrated themes based on the results were developed. Five main themes were the energy and climate change, water resource and environmental pollution, sustainable village and sustainable food production, sustainable city and sustainable production, sustainable tourism and biodiversity. I hope these could function as theme of integrated-content. Based on the results of study, I propose joint researches on scope of sustainable development for environmental education.

• Journal of Convergence for Information Technology
• /
• v.7 no.4
• /
• pp.39-43
• /
• 2017

The purpose of this study was to investigate of effect of medial & inferior gliding of patella using non-elastic taping on muscle activation of vastus medialis & vastus lateralis during sit to st&ing. As a result of measure, it was confirmed that the muscle activity of vastus medialis is higher than total muscle activity when the inferomedial gilding compared to the medial gliding. The medial & downward gliding of patella more stable than medial direction. especially it will be effective on prevent or control of Patellofemoral pain syndrome. In this regard, the development of orthosis & sportswear for inferomedial gliding to patella will be efficiency to maintain healthy the knee joint.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.6
• /
• pp.821-830
• /
• 2010

Deck plates and hatch coming of large container carrier and offshore structures are joined by ultra-thick plates whose thickness is more than 60mm. Traditionally FCAW has been used to join the thick plates in butt joint. However, FCAW has been replaced with EGW since the welding efficiency of EGW is higher than that of FCAW. Tandem EGW using two electrodes has been applied to vertical position welding by several shipyards. EGW requires one or two layers of bead whereas FCAW requires more than 20 layers of weld bead in thick welding. However, high welding residual stresses are generated by EGW since it uses higher heat input than FCAW. In the present study, a finite element model is suggested to predict the residual stresses induced by the tandem EGW. Butt specimen of EH40 TMCP shipbuilding steel plates vertical welding was modeled by a three-dimensional model. Residual stresses were measured by X-ray diffraction method and to verify the numerical result. The results show a good agreement with experimental result.

• Journal of the Korea Society of Computer and Information
• /
• v.10 no.3 s.35
• /
• pp.55-64
• /
• 2005

The avatar can be used as an auxiliary methodology of text and image communications in cyber space. An intelligent communication method can also be utilized to achieve real-time communication, where intelligently coded data (joint angles for arm gestures and action units for facial emotions) are transmitted instead of real or compressed pictures. In this paper. for supporting the action of arm and leg gestures, a method of generating the facial expressions that can represent sender's emotions is provided. The facial expression can be represented by Action Unit(AU), in this paper we suggest the methodology of finding appropriate AUs in avatar models that have various shape and structure. And, to maximize the efficiency of emotional expressions, a comic-style facial model having only eyebrows, eyes, nose, and mouth is employed. Then generation of facial emotion animation with the parameters is also investigated.