• 소음진동
• /
• 제7권1호
• /
• pp.61-69
• /
• 1997

Despite of the development in the finite element method, it is difficult to get the finite element model describing the dynamic characteristics of the complex structure exactly. Therefore a number of different methods have been developed in order to update the finite element model of a structure using vibration test data. This paper outlines the basic formulation for the frequency response function based updating method. One important advantage of this method is that the intermediate step of performing an eigensolution extraction is unnecessary. Using simulated experimental data, studies are conducted in the case of 10 DOF discrete system. The solution of noisy and incomplete experimental data is discussed. True measured frequency response function data are used for updating the finite element model of a beam and a plate. Its applicability to the joint identification is also considered.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.413-418
• /
• 1998

In this paper, a dynamic modeling approach is introduced to identify the dynamic characteristics of the structural/mechanical joints within an one-dimensional structure. A structural joint is represented by the four-pole parameters and the four-pole parameters are determined from the measured frequency response functions by using the spectral element method. As the illustrative examples, a cantilevered beam and a clamped-clamped beam, each consists of two beams connected by a bolted joint, are investigated to evaluate the present modeling approach. It is found that the dynamic responses predicted by using the identified four-pole parameters for the bolted joint are well agreed with the dynamic responses measured up to high frequency.

• 한국가구학회지
• /
• 제17권2호
• /
• pp.25-34
• /
• 2006

This experiment was carried out to investigate the high-frequency gluing characteristics of poly vinyl acetate emulsion adhesive(PVAc) on MDF edge-glued boards. The edge-glued boards were glued lengthwise with butt, scarf, or finger joint. The wastes of MDF boards were reused as board materials. The obtained results are summarized as follows; the bending strength of edge-glued MDF increased slightly with the HF heating time, but the economically desirable heating time was 6 minutes. The bending and tensile strength of edge-glued MDF were high with scarf, finger and butt joint, in order. The strength of finger jointed MDF showed 80% of scarf jointed MDF. The effects of location of finger joints on the bending strength of edge-glued MDF were larger than those of the numbers of finger joints. The bending strength of edge-glued MDF with one joint on the middle position showed 40% decrease in comparison with non-jointed MDF.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 1997년도 춘계학술대회논문집
• /
• pp.100-106
• /
• 1997

The purpose of this study is to measure perceived joint discomfort in the seated and standing position, and to provide a ranking system of joint discomfort measured in this study. Seven male subjects with no history of musculo-skeletal disorders participated in the experiment. Their physical characteristics were: age -$27.6 {\pm}1.8$ years, stature -$171.0 {\pm}5.5cm$, and body weight -$66.4{\pm}9.3kg$. The results showed that perceived joint discomfort was different depending on the human body joints involved in motion and their movement directions, which imply that the human body motions should be classified intoseveral distinct classes that need to be assigned different weights of postural stress. In the seated postion, the hip movement was the most stressful, the back was the second, and the shoulder was the third. Similarly, in standing postures, the hip was given the highest ranking, followed by the back, and the wrist.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 가을 학술발표회 논문집
• /
• pp.237-242
• /
• 1993

Precast concrete panel buildings are designed to tracsmit shear forces through the joint between the reinforced concrete panels. The shear strength is partly provided by the resistance to sliding at the interface between the precast and in- situ concrete and partly by the dowel action of the reinforcement crossing the joint. The shear resistance to sliding is largely dependent on the shapes and configurations of vertical joints and the vertical loads of horizontal joints. In this paper, the shear strength by the difference of relative strength between panel and joint, the effect of reinforcement, and the effect of vertical load are considered.

• 대한기계학회논문집A
• /
• 제24권5호
• /
• pp.1203-1214
• /
• 2000

In this paper, a failure model for co-cured steel-composite tubular single lap joints has been proposed incorporating the nonlinear mechanical behavior of steel adherends and different failure mode s such as steel adherend failure and composite adherend failure. The characteristics of the co-cured steel-composite tubular single lap joint were investigated with respect to the test temperature, the stacking sequence of composite adherend, the thickness ratio of steel adherend to composite adherend, and the scarf ratio of steel adherend. Thus, the optimum design method for the co-cured steel-composite tubular single lap joint was suggested.

• 제어로봇시스템학회논문지
• /
• 제14권12호
• /
• pp.1278-1285
• /
• 2008

An optimization-based real-time joint angle extraction method of human elbow is proposed by processing the biomedical signal of surface EMG (electromyogram) measured at the center point of biceps brachii. The EMG signal is known as non-stationary (time-varying) signal, but we assume that it is quasi-stationary because a physical or physiological system has limitations in the rate at which it can change its characteristics. Based on the assumption, a pre-processing method to obtain pre-angle values from raw EMG signal is firstly suggested, and then an optimization method to minimize the error between the pre-angle and real joint angle is proposed in this paper. Finally, we suggest the experimental results showing the effectiveness of the proposed algorithm.

• Journal of the Korean Wood Science and Technology
• /
• 제23권4호
• /
• pp.91-97
• /
• 1995

Cyclic tests were performed with dowel joints which are being widely used for furniture manufacturing in Korea. In this study, effects of various factors-such as species of joint members, diameter and length of dowels, and space between dowels-on stiffness, strength and damping ratio of joints were evaluated and concluded as follows: 1. Under cyclic loads, failure of dowel joints were caused by bending failure of dowels. 2. Dowel joints were evaluated to be stiff but general load carrying capacities were relatively low. 3. Joint moduli and damping ratios of dowel joints decreased as diameter and length of dowels, and space between dowels increased. 4. In dowel joints, properties of dowel itself have greater effects on stiffness and strength of joints than properties of joint members.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.539-544
• /
• 2000

The purpose of this study is to develop the mechanical anchorage, namely MAB-BOP (Mechanical Anchorage of 90$^{\circ}$ Hooked Bars with BOlt nad Plate) of the beam-column joint in precast concrete framed structures. Six specimens simulating typical interior beam-column joints were tested to investigate the mechanical characteristics of MAB-BOP. Of primary interest was the measurement of the slip of the anchored bar. Th load-slip curve obtained from this test were used to compare the mechanical performances of the different anchoring methods. Based on the test results, it was found that MAB-BOP showed sufficient anchoring strength capacity compared to 90$^{\circ}$ hooked bar method. So, MAB-BOP can be used as the anchoring methods of the reinforcing bars in PC beam-column joint.

• KCI Concrete Journal
• /
• 제13권1호
• /
• pp.27-34
• /
• 2001

This paper presents the results of a study on the effects of pounding at expansion joints of concrete bridges under earthquake ground motions. An engineering approach, rather than continuum mechanics, is emphasized. First, the sensitivity analysis of the gap element stiffness is performed. Second, usefulness of the analysis method for simulation of pounding phenomena is demonstrated. Third, the effects of pounding on the ductility demands measured in terms of the rotation of column ends are investigated. Two-dimensional FE analysis using a bilinear hysterestic model for bridge substructure joints and a nonlinear gap element for the expansion joint is performed on a realistic bridge with an expansion joint. Effects of the primary factors on the ductility demand such as gap sizes and characteristics of earthquake ground motion are investigated through a parametric study. The major conclusions are that pounding effect is generally negligible on the ductility demand for wide practical ranges of gap size and peak ground acceleration, but is potentially significant at the locations of impact.