• 임산에너지
• /
• 제18권2호
• /
• pp.70-77
• /
• 1999

간벌 소경재의 새로운 용도개발을 위한 기초연구로서 국내산 주요 침·활엽수 4수종의 알칼리팽윤 특성을 조사하였다. 그 결과, 4수종 모두 알칼리 처리후 밀도가 증가하였으며 그 정도는 활엽수재가 더 크게 나타났다. 알칼리처리에 의해 접선방향의 팽윤이 현저한 반면 방사방향의 팽윤은 작았고, 섬유방향은 오히려 감소하는 경향이 있었다. 알칼리 팽윤후 수축율은 활엽수재가 더 컸으며, 특히 기건상태까지의 수축율은 방사방향과 접선방향간에 수축육의 차이가 거의 없이 등방적으로 수축하는 특징을 보여주었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.159-160
• /
• 2007

• Computers and Concrete
• /
• 제5권5호
• /
• pp.435-448
• /
• 2008

Self-compacting concrete (SCC), characterized by the high flowability and resistance to segregation, is due to the high amount of paste (including cement and mineral admixtures) in contrast with normal concrete (NC). However, the high amount of paste will limit the volume fractions of coarse aggregate,and reduce the tendency of coarse aggregate to suppress drying shrinkage deformations. For this reason, SCC tends to produce higher values of drying shrinkage than NC for the most part. In order to assess the drying shrinkage of SCC quantitatively for application to offshore caisson foundations, the formulas presented in the literatures (ACI 209 and CEB-FIP) are used to predict the values of drying shrinkage in SCC according to the corresponding mix proportions. Additionally, a finite element (FE) model, which assumes concrete to be a homogeneous and isotropic material and follows the actual size and environmental conditions of the caisson, is utilized to simulate stress distribution situations and deformations in the SCC caisson resulting from the drying shrinkage. The probability of cracking and the behavior of drying shrinkage of the SCC caisson are drawn from the analytic results calculated by the FE model proposed in this paper.

• Restorative Dentistry and Endodontics
• /
• 제28권6호
• /
• pp.457-466
• /
• 2003

The aim of study was to investigate the effect of flow, specimen geometry and adhesion on the measurement of linear polymerization shrinkage of light cured composite resins using linear shrinkage measuring device. Four commercially available composites - an anterior posterior hybrid composite Z100, a posterior packable composite P60 and two flowable composites, Filtek flow and Tetric flow-were studied. The linear polymerization shrinkage of composites was determined using 'bonded disc method' and 'non-bond-ed' free shrinkage method at varying C-factor in the range of 1∼8 by changing specimen geometry. These measured linear shrinkage values were compared with free volumetric shrinkage values. The viscosity and flow of composites were determined and compared by measuring the dropping speed of metal rod under constant load. In non-bonded method, the linear shrinkage approximated one third of true volumetric shrink-age by isotropic contraction. However, in bonded disc method, as the bonded surface increased the linear shrinkage increased up to volumetric shrinkage value by anisotropic contraction. The linear shrinkage value increased with increasing C-factor and approximated true volumetric shrinkage and reached plateau at about C-factor 5∼6. The more flow the composite was, reduced linear shrinkage was measured by compensation radial flow.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.284-285
• /
• 2006

The nano-sized Fe powders were prepared by plasma arc discharge process using pure Fe rod. The microstructure and the sintering behavior of the prepared nanopowders were evaluated. The prepared Fe nanopowders had nearly spherical shapes and consisted of metallic core and oxide shell structures. The higher volume shrinkage at low sintering temperature was observed due to the reduction of surface oxide. The nanopowders showed 6 times higher densification rate and more significant isotropic shrinkage behavior than those of micron sized Fe powders.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.157-158
• /
• 2006

A novel nanofabrication process has been developed using two-photon crosslinking (TPC) for the fabrication of three-dimensional (3D) SiCN ceramic microstructures applicable to high functional 3D devices, which can be used in harsh working environments requiring a high temperature, a resistance to chemical corrosion, as well as tribological properties. After sequential processes: TPC and pyrolysis, 3D ceramic microstructures are obtained. However, large shrinkage due to low-ceramic yield during the pyrolysis is a serious problem to be solved in the precise fabrication of 3D ceramic microstructures. In this work, silica nanoparticles were employed as a filler to reduce the amount of shrinkage. In particular, the ceramic microstructures containing 40 wt% silica nanoparticles exhibited relatively isotropic shrinkage owing to its sliding free from the substrate during pyrolysis.

• 임산에너지
• /
• 제20권1호
• /
• pp.62-72
• /
• 2001

목재의 알칼리 팽윤특성을ㄹ 해명하기 위해 국내산 주요 침·활엽수 4수종의 주요 구성요소의 알칼리 팽윤 거동을 횡단면 절편을 이용하여 조사하였다. 그 결과, 일본잎갈나무의 가도관 직경은 잣나무보다 크게 팽윤하였으며, 가도관의 벽두께는 10% 이상의 알칼리 수용액에 처리시 높은 팽윤율을 나타냈다. 알칼리 처리에 의해 도관의 직경은 방사방향으로 수축하였고, 접선방향으로 다소 팽윤하였다. 목섬유의 세코벽두께는 5%의 알칼리처리에서도 수분팽윤에 비해 3배 이상의 높은 팽윤성을 나타앴고, 알칼리 처리후 일본잎갈나무의 가도관 직경, 목섬유 직경 및 세포벽두께는 거의 등방적인 수축현상을 보여주었다. 또한 미처리 시료에 비해 머서화 처리 구성요소의 세포직경은 수축되었고, 세포벽은 팽윤되었다. 알칼리처리 과정에서 셀룰로오스 결정형의 변화는 없었지만 상대결정화도와 미결정의 폭이 다소 증가되었다. 결론적으로 알칼리의 농도, 수종, 세포의 종류가 목재의 알칼리 팽윤 특성에 크게 관여하는 것으로 생각되었다.

• 방사성폐기물학회지
• /
• 제18권1호
• /
• pp.31-41
• /
• 2020

본 연구에서는 우라늄 폐촉매 처리 공정에서 발생하는 우라늄 함유 폐기물 대상으로 유리-세라믹 매질 구조의 대형 디스크 소결체 형태로 제작 시, 최종 제작된 소결체의 비등방향 수축 특성 및 변형율 변화를 연구하였다. 본 연구에서는 최대 직경 40 cm를 갖는 다양한 크기 원형 디스크 형태와 원형 디스크의 1/4 크기의 부채꼴 형 소결체를 제작하여 이들의 비등방성 수축 특성을 평가하였다. 60 MPa 압력하에서 만들어지는 성형체는 소결 시 성형체의 크기 및 형태에 관계없이 높은 등방성 수축하였다. 제조된 전체 소결체에 대한 비등방성율은 평균 1.6%이었고 이때 평균 부피 감용율은 37.4% 이었다. 이러한 결과로부터 국내에서 발생한 우라늄 폐촉매를 처리하기 위한 공정에서 발생하는 우라늄 함유 폐기물은 대형 디스크 형태의 유리-세라믹 매질 형태로 고형화함으로써 높은 안정성과 부피감용 효과를 가지며 200 L 드럼에 포장될 수 있음이 확인되었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.788-790
• /
• 2003

Closed-cell type barrier ribs of PDP were formed by capillary molding process using molds prepared by inclined UV lithography process. Various types of molds with different inclined angles were prepared by patterning SU-8 thick photoresist film and casting with PDMS. The ribs with various type cells were successfully formed by the process. The effects of inclined angle on the distortion of barrier ribs during sintering were investigated. The results indicated that the barrier ribs with a draft angle and dimensional change does not affect the distortion of the barrier ribs during sintering, suggesting that the closed-cell must be isotropic in sintering shrinkage.

• 한국전기전자재료학회논문지
• /
• 제28권12호
• /
• pp.781-786
• /
• 2015

It is necessary for ferrite sheets to be fabricated with high packing density for excellent electrical properties and high strength. In this study, the relationship between the warpage and the packing density of ferrite green sheet, was investigated with amount variation of organic additives. With 0.4 wt% of dispersant, the packing density was about 48% and warpage appeared 0.5~1.3 mm high. With 1.4 wt% of dispersant, the packing density increased up to 57% and warpage appeared 0.8~2.1 mm high. With high packing density, warpage appeared along the edges of specimen, while with low packing density, deformation appeared over whole specimen inhomogeneously. It is thought that inhomogeneous deformation after sintering came from the inhomogeneity in green sheet prepared with badly dispersed slurry. With good homogeneity in green sheet from well-dispersed slurry, isotropic shrinkage is thought to have occurred along the distance from center to edges of specimen during sintering.