• Geotechnical Engineering
• /
• v.10 no.3
• /
• pp.111-118
• /
• 1994

A series of drained cubical triaxial tests was performed to investigate the finfluence of the intermediate principal stress on the deformation and strength characteristics of sand. Test results showed that the strength of sand as represented by the friction angle increased from triaxial compression condition (b:0) with increasing magnitude of the intermediate principal stress until the vus of b reached 0.75, land it decreased slightly with closing to b= 1. Also it was found that the projection of the plastic strain increment vector on the octahedral plane was perpendicular to the trace of the failure surface on that plane. The prediction by the isotropic single hardening model sllowed good coinidence with experimental results.

• Steel and Composite Structures
• /
• v.17 no.2
• /
• pp.185-198
• /
• 2014

Carbon-manganese steel A42 (French standards) is used in steam generator pipes of nuclear center and subject to low cycle fatigue (LCF) loads. In order to obtain the material LCF behavior, the tests are implemented in a hydraulic fatigue machine. The LCF plastic deformation and cyclic stress in macroscope have been influenced by the accumulated low cycle fatigue damage. The constitutive kinematic and isotropic hardening modeling is modified with coupling fatigue damage to describe the fatigue behavior. The improved model seems to be good agreement with the test results.

• Transactions of Materials Processing
• /
• v.7 no.6
• /
• pp.594-602
• /
• 1998

The design analysis of axisymmetric, multi-stage deep drawing dies was performed using the rigid-viscoplastic finite element formulation. In the formulation the axisymmetric CFS algorithm was employed. Hill's non-quadratic normal anisotropic yield criterion and isotropic hardening rule were considered. For trial initial displacements and tool contact points. the geometric force equilibrium method was adopted. In order to see the validity of the formulation, the multi-stage deep drawing processes of shell-cylinder front part of hydraulic booster were simulated. The simulation showed good agreements with measurments and PAM-STAMP results.

• Coupled systems mechanics
• /
• v.11 no.2
• /
• pp.133-149
• /
• 2022

The accurate prediction of elastoplasticity under prescribed workloads is essential in the optimization of engineering structures. Mechanical experiments are carried out with the goal of obtaining reliable sets of material parameters for a chosen constitutive law via inverse identification. In this work, two sample geometries made of high strength steel plates were evaluated to determine the optimal configuration for the identification of Ludwik's nonlinear isotropic hardening law. Finite element model updating(FEMU) was used to calibrate the material parameters. FEMU computes the parameter changes based on the Hessian matrix, and the sensitivity fields that report changes of computed fields with respect to material parameter changes. A sensitivity analysis was performed to determine the influence of the sample geometry on parameter identifiability. It was concluded that the sample with thinned gauge region with a large curvature radius provided more reliable material parameters.

• Journal of the Korean Society of Industry Convergence
• /
• v.15 no.1
• /
• pp.21-27
• /
• 2012

Decomposed granite soils are in a wide range of conditions depending on the degrees of weathering. This paper is intended to examine laboratory tests such as consolidation tests and conventional triaxial compression tests conducted in order to find out the mechanical properties of Cheongju granite soil. Along with the foregoing, the results of basic physical tests conducted in order to grasp the physical properties of Cheongju granite soil were described and based on the results, methods to calculate the mechanical parameters of numerical approaches using Lade's double surface work-hardening constitutive model were examined. Finally, it is intended to explain the stress properties of Cheongju granite soil used as a geotechnical material based on its shear behavior and critical state concept using the results of isotropic consolidation tests and triaxial compression tests. As a conclusion, it can be seen that in the relationship between confining stress and maximum deviator stress, the slope is maintained at a constant value of 2.95. In the drained CTC test, maximum deviator stress generally existed in a range of axial strain of 6~8% and larger dilatancy phenomena appeared when confining stress was smaller. Finally, based on the results of the CTC tests on Cheongju granite soil, although axial strain, deviator stress and pore water pressure showed mechanical properties similar to those of overconsolidated soil, Cheongju granite soil showed behavior similar to that of normally consolidated soil in terms of volumetric strain.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.6
• /
• pp.545-554
• /
• 2000

Compton X-ray backscatter technique has been used to quantitatively assess the impact damage in quasi-isotropic laminated composites and to obtain a cross-sectional profile of impact-damaged laminated composites from the density variation of the cross section. An adaptive filter is applied to the Compton backscattering data for the reconstruction and noise reduction from many sources including quantum noise, especially when the SNR(signal-to-noise ratio) of the image is relatively low. A nonlinear reconstruction model is also proposed to overcome distortion of the Compton backscatter image due to attenuation effects, beam hardening, and irregular distributions of the fibers and the matrix in composites. Delaminations masked or distorted by the first few delaminations near the front surface are detected and characterized both in width and location, by application of an error minimization algorithm.

• Structural Engineering and Mechanics
• /
• v.32 no.5
• /
• pp.649-665
• /
• 2009

This paper reports part of a comprehensive research study conducted at the University of Queensland on the ability of CFRP web-bonded systems in strengthening an exterior beam-column joint subjected to monotonic loads. One 1/2.2 scaled plain and four CFRP repaired/retrofitted joints subjected to monotonic loads were analysed using the nonlinear finite-element program ANSYS and the results were calibrated against experiments. The ANSYS model was employed in order to account for tension stiffening in concrete after cracking and a modified version of the Hognestad's model was used to model the concrete compressive strength. The stress-strain properties of main steel bars were modelled using multilinear isotropic hardening model and the FRPs were modelled as anisotropic materials. A perfect bond was assumed as nodes were shared between adjacent elements irrespective of their type. Good agreement between the numerical predictions and the experimental observation of the failure mechanisms for all specimens were observed. Closeness of these results proved that the numerical analysis can be used by design engineers for the analysis of web-bonded FRP strengthened beam-column joints with confidence.

• Tribology and Lubricants
• /
• v.28 no.1
• /
• pp.19-26
• /
• 2012

Rolling contact fatigue of an urban railway wheel was analysed during its rolling. A FEM analysis was performed using a 3D modelling of rail and wheel, considering the slope of the rail and nonlinear isotropic and kinematic hardening behavior of the rail and the wheel. The maximum von-Mises stress and contact pressure between the rail and wheel were 656.9 MPa and 1111.4 MPa, respectively, under axial load of 85 kN with friction coefficient of 0. The fatigue initiation life prediction relationships by strain-lifetime (${\varepsilon}$-N) and Smith-Watson-Topper method were drawn for the wheel steel as follows: $N_i=7.35{\times}10^6{\times}SWT^{-3.56}$ and $N_i=5.41{\times}10^{-9}{\times}(\frac{{\Delta}{\varepsilon}}{2})^{-5.77}$. The fatigue lifetimes of the wheel due to rolling contact were determined to be infinite by ${\varepsilon}$-N and SWT methods.

• Journal of the Korean Society of Safety
• /
• v.19 no.4 s.68
• /
• pp.135-140
• /
• 2004

Wear mechanisms may be briefly classified by mechanical, chemical and thermal wear. A plane strain finite element method is used with a new material stress and temperature fields to simulate orthogonal machining with continuous chip formation. Deformation of the workpiece material is healed as elastic-viscoplastic with isotropic strain hardening and the numerical solution accounts for coupling between plastic deformation and the temperature field, including treatment of temperature-dependent material properties. Effect of the uncertainty in the constitutive model on the distributions of strait stress and temperature around the shear zone are presented, and the model is validated by comparing average values of the predicted stress, strain, and temperature at the shear zone with experimental results.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.1 s.44
• /
• pp.29-43
• /
• 2000

In this study, the computationally efficient inelastic buckling analysis program is developed to be used as the research tool in finding buckling strength of inelastic members. The program can determine buckling loads and buckled shapes of elastic and inelastic members which failed by flexural, lateral-torsional and/or local buckling. It can analyze singly and doubly symmetric I-shape members. In the program, the web of the member is modeled using the plate element and the flanges are modeled by beam elements. Multilinear isotropic hardening rule and the incremental theory of plasticity are used to simulate the inelastic stress-strain relationship from material tests. The program is verified using theoretical solutions and experimental results. The results from the program show good agreement with those from experiments and theory.