• Particle and aerosol research
• /
• v.9 no.4
• /
• pp.221-230
• /
• 2013

We demonstrated the efficacy of magnetic nanoparticles (MNPs) produced from a low grade iron ore as an adsorbent for the removal of Cr(VI), a toxic heavy metal anion present in wastewater. The adsorption of Cr(VI) by these MNPs strongly depended on the dosage of MNPs, the initial concentration of the Cr(VI) solutions, and pH. The highest Cr(VI) adsorption efficiency of 22.0 mg/g was observed at pH 2.5. The adsorption data were best fit with the Langmuir isotherm and corresponded to a pseudo-second-order kinetic model. The used adsorbent was regenerated by eluting in highly alkaline solutions. Sodium bicarbonate showed the highest desorption efficiency of 83.1% among various eluents including NaOH, $Na_2HPO_4$, and $Na_2CO_3$. Due to the high adsorption capacity, the simple magnetic separation, and the high desorption efficiency, this nano-adsorbent produced from inexpensive and abundant resources may attract the attention of the industries to apply for removing various metal anionic contaminants from wastewater.

• Advances in concrete construction
• /
• v.5 no.6
• /
• pp.671-683
• /
• 2017

Commonly used concrete in general, consists of cement, fine aggregate, coarse aggregate and water. Natural river sand is the most commonly used material as fine aggregate in concrete. One of the important requirements of concrete is that it should be durable under certain conditions of exposure. The durability of concrete is defined as its ability to resist weathering action, chemical attack or any other process of deterioration. Durable concrete will retain its original form, quality and serviceability when exposed to its environment. Deterioration can occur in various forms such as alkali aggregate expansion, freeze-thaw expansion, salt scaling by de-icing salts, shrinkage, attack on the reinforcement due to carbonation, sulphate attack on exposure to ground water, sea water attack and corrosion caused by salts. Addition of admixtures may control these effects. In this paper, an attempt has been made to replace part of fine aggregate by tailing material and part of cement by fly ash to improve the durability of concrete. The various durability tests performed were chemical attack tests such as sulphate attack, chloride attack and acid attack test and water absorption test. The concrete blend with 35% Tailing Material (TM) in place of river sand and 20% Fly Ash (FA) in place of OPC, has exhibited higher durability characteristics.

• Economic and Environmental Geology
• /
• v.19 no.2
• /
• pp.85-96
• /
• 1986

The Bupyeong Silver mine which is located approximately 35km west of Seoul is currently the leading silver producer in Korea. The deposits occur as stockwork deposits hosted in Jurassic pyroclastic rocks. Occurrences of ore deposits and mineral paragenesis suggest a division of mineralization into four stages: Stage I, deposition of iron oxide and base metal sulfides; Stage II, deposition of tin oxide and silverm inerals; stage III, deposition of native silver and other silver minerals; Stage IV, formation of pyrite bearing siderite veinlets, Silver minerals in ore are native silver, argentite, freibergite, pyrargyrite, canfieldite, polybasite, dyscrasite and Ag-Fe-S mineral. The most important silver mineral is native silver among them. Chemical composition of important silver minerals were determined by electron probe microanalyser. Assay, size and modal analyses for floatation products were carried out. In floatation products, relative proportion of native silver for total important silver minerals have following ranges: feed, 64.7 to 74.74 wt.%; A-cleaner concentrate, 80.58 to 98.79 wt.%; and final tailing, 28.12 to 72. 57 wt. %. Average degree of liberation for native silver in feed and A-cleaner concentrate are 60.49% and 77.57% respectively. Negative relationship can be recognized between native silver and argentite in their abundance and behavior in floatation precesses.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.4
• /
• pp.359-370
• /
• 2009

Arsenic and heavy metals leached out as a result of oxidation of tailings exposed to the surface pose a serious environmental contamination of mine areas. This study investigated how arsenic behavior is controlled by a variety of processes, such as oxidation of sulfides and formation or alteration of secondary minerals, based on mineralogical methods. The study was carried out using the tailing samples obtained from Nakdong mine located in Jeongseongun, Gangwondo. After separating magnetic and non-magnetic minerals using pretreated tailing samples, each mineral sample was classified according to their colors and metallic lusters observed by the stereoscopic microscope. Subsequently, the mineralogical properties were determined using various instrumental analyses, such as x-ray diffractometer (XRD), energy dispersive spectroscopy (EDS), and electron probe micro analyzer (EPMA). The literature review confirmed that various ore minerals were identified in the Nakdong ore deposits. In this study, however, there were observed a few original ore minerals as well as secondary and/or tertiary minerals newly formed as a result of weathering including oxidation. In particular, we did not recognize pyrrhotite which has been known to originally exist in a large abundance, but peculiarly colloform-type iron (oxy)hydroxides were identified, which indicates most of pyrrhotite has been altered by rapid weathering due to its large reactivity. In addition, a secondary scorodites filling the fissure of weathered primary arsenopyrites were identified, and it is speculated that arsenic is immobilized through such a alteration reaction. Also, we observed tertiary iron (oxy)hydroxides were formed as a result of re-alteration of secondary jarosites, and it suggests that the environment of tailing has been changed to high pH from low pH condition which was initiated and developed by oxidation reactions of diverse primary ore minerals. The environmental change is mainly attributed to interactions between secondary minerals and parental rocks around the mine. As a result, not only was the stability of secondary minerals declined, but tertiary minerals were newly formed. As such a process goes through, arsenic which was immobilized is likely to re-dissolve and disperse into surrounding environments.

• Resources Recycling
• /
• v.25 no.4
• /
• pp.23-31
• /
• 2016

It was found that there was no problem in recycling by-products (waste rock and tailings) from Yangyang iron mine themselves through matter conversion because they are not hazardous according to results of KSLT method. In case of using tailings as sub-materials of cement, it recommended the use of less than 3% tailings dosage not to exceed 0.6% of total alkali ($R_2O$) content based on standard quality of portland cement (KS L 5201). Non sintered eco-brick corresponding to class 1 quality of recycled clay brick (KS I 3013) can replace 15% of cement with tailings and 100% of general fine aggregate with waste rock from iron mine. As mentioned above, recycling the by-products (waste rock and tailings) as sub-materials of cement and non sintered eco-brick could gain both environmental and economic benefits, that is, reduction of scale and maintenance cost of tailing ponds, decrease of energy use and $CO_2$ emission.

• Advances in concrete construction
• /
• v.3 no.1
• /
• pp.55-69
• /
• 2015

Tailing Material (TM) and Fly Ash (FA) are obtained as waste products from the mining and thermal industries. Studies were carried out to explore the possibility of utilizing TM as a part replacement to fine aggregate and FA as a part replacement to cement, in concrete mixes. The effect of replacing fine aggregate by TM and cement by FA on the standard sized specimen for compressive strength, split tensile strength, and flexural strengths are evaluated in this study. The concrete mix of M40 grade was adopted with water cement ratio equal to 0.40. Concrete mix with 35% TM and 65% natural sand (TM35/S65) has shown superior performance in strength as against (TM0/S100, TM30/S70, TM40/S60, TM50/S50, and TM60/S40). For this composition, studies were performed to propose the optimal replacement of Ordinary Portland Cement (OPC) by FA (Replacement levels studied were 20%, 30%, 40% and 50%). Replacement level of 20% OPC by FA, has shown about 0-5% more compressive strength as against the control mix, for both 28 day and 56 days of water curing. Interestingly results of split tensile and flexural strengths for 20% OPC replaced by FA, have shown strengths equal to that of no replacement (control mix).

• Resources Recycling
• /
• v.1 no.1
• /
• pp.69-77
• /
• 1992

In this study, a talc flotation was fundamentally carried out with dolomite origin talc ore produced in Dong Yang Talc Mine at Chung-Ju. This ores are mainly composed with talc as a valuable mineral, dolomite as a gangue mineral and other minor minerals of hornblende, tremolite, actinolite, chlorite, calcite, epidote and iron oxide. In order to obtain some of fundamental data for the talc flotation from low grade dolomitic talc tailings which were abandoned -25mm +17 mm size, after the treatment of crude talc ores by screening and hand -picking at the mine, flotation characteristics of the pure talc and dolomite in this ores were first investigated by measuring floatability of the minerals at some experiment conditions. Furthermore, Several times of batch flotations for talc were performed experimentally to recover talc from the low grade dolomitic talc tailings. From the results obtained in this experiment, the conclusions can be summarized as follows ; 1) In the flotation of pure talc, the use of Dowfroth 250 as frother was the most effective in various kinds of frother and the proper addition amount was about 50 mg/${\ulcorner}$(200g/t) at the condition of this experiment. 2) In the flotation of pure talc, the use of kerosene as collector was not adequate, at the addition over 50mg/l of Dowfroth 250. 3) The adequate pH of pulp ranged from pH6 to pH9 in the talc flotation using Dowfroth 250 as frother. 4) The use of Quebracho as depressant for dolomite was not adequate for the recovery of talc, and more selective depressant was required. 5) In the talc flotation on D sample(dolomitic talc tailing), the suitable number of cleaning time was about 3. 6) At this experimental conditions for the talc flotation on D sample, the talc flotation concentrates of 1. 40% CaO and 84.5 whiteness could be recovered with the talc recovery of about 53%.