• Macromolecular Research
• /
• v.12 no.5
• /
• pp.431-436
• /
• 2004

Cross-linked network solid polymer electrolytes were prepared by means of in situ hydrosilylation between poly[hydromethylslioxane-g-oligo(ethylene oxide)] and diallyl or triallyl group-containing poly(ethylene glycols). The conductivities of the resulting polymer electrolytes were greatly enhanced upon the addition of poly(ethylene glycol) dimethyl ether (PEGDME) as an ion-conducting plasticizer. Conductivities of the cross-linked polymer electrolytes were more dependent on the molecular weight of PEGDME than on the cross-linkers. The maximum conductivity was found to be 5.6${\times}$10$\^$-4/ S/cm at 30$^{\circ}C$ for the sample containing 75 wt% of PEGDME (M$\_$n/ =400). These electrolytes exhibited electrochemical stability up to 4.5 V against the lithium reference electrode. We observed reversible electrochemical plating/stripping of lithium on the nickel electrode.

• Journal of the Korean institute of surface engineering
• /
• v.4 no.1
• /
• pp.16-23
• /
• 1971

In this study , fluoborte solution consisting of lead fluoborate, tin fluoborate and cupric acetate was used. By addition of small amount of Cu+= ion to the solution, the Cu content of deposition layer was almost controlled less than 5%. The amount of Cu in deposition layer was almost constant without any influence of Pb++ & Sn++ in the solution, and the amount of Pb was increased by the increase of total concentration of Pb++ +Sn++ in the solution, and the amount of Pb was increased by the increase of total concentration of Pb++ +Sn++ in the solution . Agitation of plating solution & low current density result in the increase of Cu content. Analyzing of microscopic structures and etching tests of the deposited alloy, it was believed that the alloy had a lamellar structure consisting of copper rich lamellar and lead rich layer.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.2
• /
• pp.73-79
• /
• 1991

Recent studies son surface coatings have shown that the change of physical, chemical and crystallographic structure analysed and observed according to the deposition process variables has the effects on the resultant film properties. Under the same preparation condition conditions of the substrate and process variables, physical morphology variations characterized by substrate temperature and bias which offect the surface mobility of adatom and adhesion variations related to the formation of Ti interlayer were considered in the present study. Microhardness showed the highest value around 40$0^{\circ}C$ of the substrate temperature and increased with the substrate bias. Adhesion was improved with the increase of substrate temperature and bias. An interlayer of pure titanium formed prior to deposition of TiN improves the adhesion at its optimum thickness. These results were explained by the change of physical morphology and phase analysis.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.4
• /
• pp.565-573
• /
• 1999

Hihg Tensile Steel enables to reduce the plate thickness comparing to the case when Mild Steel is used. From the economical view points this is very preferable since the reduction in the hull weight. however to use the High Tensile Steel effectively the plate thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. If the inplane stiffness of the plating decreases due to buckling the flexural rigidity of the cross sect6ion of a ship's hull also decreases. This may lead to excessive deflection of the hull girder under longitudinal bending. In these cases a precise estimation of plate's behavior after buckling is necessary and nonliner analysis of isolated and stiffened plates is required for structural sys-tem analysis. In this connection this paper discusses nonlinear behaviour of thin plate under thrust. Based on the analytical method elastic large deflection analysis of isolated plate is perform and simple expression are derived to evaluated the inplane rigidity of plates subjected to uniaxial compression.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.585-592
• /
• 1996

In order to investigate the influence of gas pressure in PVD deposition conditions, aluminum films were prepared by vacuum evaporation and ion plating. The crystal orientation and morphology of the films affected by argon gas pressures were characterized by using X-ray diffraction (XRD) and scanning electron micrography (SEM) respectively. With the increasing of argon gas pressure, the preferred orientation of aluminum films exhibited (200) and the diffraction peaks of the films became less sharp and broadened. Film's morphology changed from columnar structure to granular structure with the increase of gas pressure. And the properties of these films on corrosion behaviors were estimated by measuring anodic polarization curves in deaerated 3% NaCl solution. The aluminum films which exhibited granular structure with (200) preferred orientation showed good corrosion resistance.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.11a
• /
• pp.63-63
• /
• 2001

As a new approach to substitute for a hard alloy of stellite 6B containing Co which is radioactive in nuclear system, a hard-phase coating of CrN will be applicable to protect 12Cr steel from erosion at leading edge on steam turbine blade. The CrN coating was prepared by arc ion plating on 12 Cr steel and was undertaken in liquid impact test at the velocity of 35Om/sec, which simulate the environment in the last stage of blade. The erosion resistance of coating was evaluated by optical observation on damaged surface. The threshold number of impact was closely related with surface hardness. And thus, it was confirmed that surface hardening improves the life time of steam turbine blade.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.6
• /
• pp.962-967
• /
• 2017

The Diamond-Like-Carbon (DLC) coating is a new carbon-based amorphous material. Carbon ions in the plasma are electrically accelerated and collide with the substrate to form a thin film. This film has similar properties to diamonds such as high surface hardness, low coefficient of friction, corrosion resistance and durability that do not react with acids and bases. Also, since there is no thermal deformation, it can be printed at room temperature. and coated on almost all materials such as paper, polymer, ceramics and various metals even aspheric lens it is possible to mirror surface coating with excellent surface roughness. In this paper, we have analyzed the DLC film formed by Filtered Arc Ion Plating (Filtered AIP) process.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.125-127
• /
• 2007

MoN 코팅막은 Ar과 $N_2$가 섞인 가스 상태 안에서 몰리브덴(Mo) 타겟을 사용해서 아크 이온 플레이팅법을 사용하여 stainless steel 표면 위에 증착을 시켰다. MoN 코팅막의 미세 결정 구조의 특징은 X-선 회절 분석(X-ray Diffractormeter, Phillips co. X'pert)과 XPS를 사용해서 측정하였다. MoN 코팅막은 순수 Mo 코팅막의 13GPa 보다 높은 25 GPa의 미세경도값을 나타냈으며, 또한 Mo 코팅막에 N의 함량이 증가할수록 마찰계수가 낮아지는 것을 알 수 있었다. 이번 연구에서는 MoN 코팅막에서 질소 함량을 변화 시켜 MoN 코팅막의 미세구조와 그 특성에 대하여 연구하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.140-141
• /
• 2007

The arc ion plating (AIP) technique has been used widely for thin coating in the area of surface engineering. The TiN coating is important in the field of dies, cutting tools and other mechanical parts. When forming the TiN films by AIP technique, the processing parameters such as arc power, bias voltage, working pressure, temperature of substrate and pre-treatment affected the adhesion respectively. The results of scratch test revealed that the adhesion strength was influenced by arc power most strongly. And a sequence of the importance of each parameters has been obtained. The crystal structure and cross-section of TiN films are also be investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.602-606
• /
• 2003

Silicon has been developed as an alternate anode material for lithium secondary batteries. A simple approach to improve the electrical contact of silicon powder has described. Carbon-coated and silver-coated silicon have been prepared by chemical vapor deposition and electroless plating respectively. Assembled cells, which consisted of surface modified silicon, lithium foil and $Li^+$ contained organic electrolyte, have been studied using electrochemical methods. Carbon-coated silicon was improved in the electrochemical performance such as reversibility and resistance compared to surface-unmodified silicon.