• Applied Chemistry for Engineering
• /
• v.26 no.3
• /
• pp.377-380
• /
• 2015

In this paper, we have investigated the optimization of $I_2$ recovery process from $NH_4I$ solution, which is generated as by-product during the amination reaction of p-diiodobenzene (PDIB) for p-phenylenediamine (PPD) synthesis. The recovered $I_2$ is then recycled as a raw material for PDIB synthesis. We have employed a cation exchange resin to recover $I_2$ from $NH_4I$ sample solution, and determined the breakthrough point and exchange capacity from the breakthrough curve. Furthermore, we have suggested optimum conditions of our $I_2$ recovery process by measuring the purity and yield of recovered $I_2$ with respect to the concentrations of $NH_4I$ and oxidant ($H_2O_2$) solutions, the oxidation time, and the temperature of drying process. Finally, the yield and purity as high as 94.96% and 96.65%, respectively were obtained by reusing the residual solution still containing unrecovered iodide ions.

• Nuclear Engineering and Technology
• /
• v.45 no.1
• /
• pp.61-66
• /
• 2013

Among the radioactive wastes generated from the nuclear power plant, a radioactive nuclide such as $^{129}I$ is classified as a difficult-to-measure (DTM) nuclide, owing to its low specific activity. Therefore, the establishment of an analytical procedure, including a chemical separation for $^{129}I$ as a representative DTM, becomes essential. In this report, the adsorption and recovery rate were measured by adding $^{125}I$ as a radio-isotopic tracer ($t_{1/2}$ = 60.14 d) to the simulation sample, in order to measure the activity concentration of $^{129}I$ in a pressurized-water reactor primary coolant. The optimum condition for the maximum recovery yield of iodine on the anion exchange resins (AG1 x2, 50-100 mesh, $Cl^-$ form) was found to be at pH 7. In this report, the effect of the boron content in a pressurized-water reactor primary coolant on the separation process of $^{129}I$ was examined, as was the effect of $^3H$ on the measurement of the activity of iodine. As a result, no influence of the boron content and of the simultaneous $^3H$ presence was found with activity concentrations of $^3H$ lower than 50 Bq/mL, and with a boron concentration of less than 2,000 ${\mu}g/mL$.

• Membrane Journal
• /
• v.26 no.5
• /
• pp.401-406
• /
• 2016

In this study, we have investigated the removal of the low level radioactive ions of Cs and I in water by the reverse osmosis (RO) process. The two RO modules produced in domestic region and the waste RO module after the cleaning process were selected. Then we compared removal performance of both Cs and I. The experiments are conducted by varying the concentration of feed, the pressure. As a results, it was confirmed that all three modules are higher I decontamination factor than Cs. And particularly, for the cleaned RO module, its decontamination factor of I was 1140. Since the results at low pressure condition were better than that at high pressure conditions, the use of the direct installation of RO modules on the tap water might be possible. In addition, it was confirmed that the waste RO module after cleaning process using EDTA, SBS and NaOH, increased the decontamination performance better than before cleaning, in particular, the recovery ratio after cleaning was 6.3% higher.

• Analytical Science and Technology
• /
• v.13 no.6
• /
• pp.751-758
• /
• 2000

A study was carried out on the dissolution of spent PWR fuels and performed on the fuels and the separation of iodide for the quantitative analysis using SIMFUEL which has chemical composition of a simulated spent PWR fuel (burn-up; 35,000 MWd/MTU and cooling time; 10 years). To dissolve the SIMFUEL effectively and to minimize the formation of volatile iodine through dissolution process, the optimum ratio of mixed acid ($HNO_3/HCl$ 80: 20 mol%) was established and ozone gas was purged. In the separation step of iodine with $CCl_4$, $NH_2OH{\cdot}HCl$ was used for reducing ${IO_3}^-$ to $I_2$.The optimum acidity of the dissolved solution and the added of $NH_2OH{\cdot}HCl$ were 2.5 M and more than $1.5{\times}10^{-3}mole$, respectively. The recovery of iodide by ion chromatography was $82.8{\pm}4.1%$ and the total yield was corrected by gamma spectrometery using $^{131}I$ as a tracer.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.4
• /
• pp.267-272
• /
• 2007

Various kinds of RI wastes are discharged from licensed organizations of radioisotopes les such as hospitals and clinic organizations, educational organizations, research institutions, and public organizations. Radioiodines such as $^{125}I\;and\;^{131}I$ are radioisotopes mainly used in nuclear medicine and industry. A method for the determination of radioiodines in RI wastes has been applied to measure low level activity using acid decomposition method and HPGe gamma ray spectrometer. Prior to analysis of real samples, $^{131}I$ reference solution and 10 g of yellow tissue paper was added to flask in mantle and was heated in 100 mL of 0.4 N $K_2Cr_2O_7$ and 100 mL of 9 M $H_2SO_4$, and then distilled after adding 10 mL of 30% $H_2PO_3$ and 1 mL of 30% $H_2O_2$. The condensed iodine by circulator was extracted into $CCl_4$, then back-extracted into the aqueous phase with 10 mL of 5% $K_2SO_2$ solution. Finally, $^{131}I$ was measured at 364.48 keV using HPGe gamma ray spectrometer after precipitation and filtration. Chemical yield of three steps such as acid decomposition process, chemical separation process, and precipitation and filtration process was more han 94% respectively, MDA(Minimum Detectable Activity) of $^{131}I$ at this analytical condition was 0.6 Bq/g.