• 한국가구학회지
• /
• 제21권3호
• /
• pp.237-247
• /
• 2010

This research was carried out to examine the properties of black charcoal board, in order to find the proper manufacturing condition for the black charcoal-board made of the charcoal. The charcoal in this study was distillated from domestic wood waste, and it were also the purpose of this study to see if the black charcoal-board has the advantageous properties of charcoal as a well-being building material against the sick house problem. Domestic wood waste was consisted of MDF 40%, PB 30%, plywood 15% and wood 15%, respectively. Black charcoal board was produced by hot pressing with following conditions; temperature $170^{\circ}C$, three stage pressing cycle of $40-10-40\;kgf/cm^2$(1min.-2.5min.-5min.) and non formaldehyde adhesives [P15%+M5%:MDI(M), poly vinyl acetate emulsion(P). Fine mixed particle size [#6-12(16.9%), #12-18(16.7%), #12-40(47.2%), #40-60(9.5%), #60-100(5.9%), less than #100(3.8%)] gave better results than larger particle size [over #6(33.8%), #12-18(17.7%), #12-40(37.7%), #40-60(6.4%), #60-100(2.6%), less than #100(1.8%)]. Final moisture content of the mat was best at 36%. Black charcoal-board showed less MOR and IB(internal bond), more WA(water absorption) than that of white charcoal-board. Black charcoal board showed not only the same gas adsorption and dimensional stability as white charcoal board but also good cutting, nailing and drilling for indoor environment systems.

• 펄프종이기술
• /
• 제45권4호
• /
• pp.1-8
• /
• 2013

High loading of printing and writing grades with fillers has many advantageous aspects in papermaking because it allows decreasing fiber use and reducing manufacturing cost. High loading technology, however, has some disadvantageous aspects as well. It decreases physical properties of papers, especially strength properties. The problem associated with high loading can be reduced by applying surface sizing starch solution onto paper surface. It is important to control the penetration of the surface sizing starch solution into paper web to obtain the desired property improvement. In this study, the effect of the addition of two polymers into starch solution on paper properties has been examined. PVOH and polyDADMAC were used as polymeric additives for surface sizing with oxidized starch. Viscosity of starch solutions and surface roughness of dried starch films on glass slides showed that some interactions between polymeric additives and oxidized starch have been occurred and the most extensive interaction with starch solution was obtained with high molecular weight polyDADMAC. Low molecular weight PVOH was most effective in improving folding endurance and internal bond strength. On the other hand, polymer addition showed no effect on surface strength of paper. This indicates that not the level of starch holdout but the bonding strength of starch itself has predominant influence on surface strength of paper.

• Journal of the Korean Wood Science and Technology
• /
• 제11권3호
• /
• pp.39-48
• /
• 1983

본(本) 연구(硏究)는 내화처리(耐火處理) 파티클보오드의 휨강도(强度)와 물리적(物理的) 성질(性質)을 조사검토(調査檢討)함으로써 내화처리(耐火處理) 파티클보오드의 제조가능성(製造可能性)을 구명(究明)하고져 실시하였다. 본(本) 연구(硏究)에서는 목재(木材)파티클을 5, 10, 15, 그리고 20%농도(濃度)의 황산암모늄과 미나리스(Minalith) 용액(溶液)에 침적(沈積)시킨후 건조(乾燥)시켜서 제조(製造)하였다. 제조(製造)된 파티클보드의 휨강도(强度)와 물리적(物理的) 성질(性質)을 조사(調査)한 결과(結果)에 따르면 휨강도(强度)에서 파괴계수(破壞係數)와 탄성계수(彈性係數)는 한국공업표준규격(韓國工業標準規格) KS F 3104의 type 100수준(水準) (100kgf/$cm^2$, $1.5{\times}10^4kgf/cm^2$)을 만족 시켰으나 두께팽창율(膨脹率)은 모두 이 규격수준(規格水準)(12%)에 이르지 못하였다. 또한 박리저항(剝離抵抗)은 미나리스의 15와 20%농도(濃度)의 경우를 제외(除外)하고는 모두 한국공업표준규격(韓國工業標準規格) KS F 3104의 type 100 수준(水準)(1.5kgf/$cm^2$을 능가(凌駕)하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제26권1호
• /
• pp.97-105
• /
• 1998

This study examined the combined using effects of urea-formaldehyde (UF) resin and emulsifiable methylene diphyenyl diisocyanate (EMDI) resin to overcome performance limit of three-layer particleboards commonly made by UF resin. Two adhesive adding methods were applied with three types of resin combination system to each layer of particleboards. The one was simultaneously spreading method with emulsified compound resin (UF and EMDI) while the other was separately spreading method with unemulsified EMDI resin after UF resin spreading. The performance of particleboards bonded with 2% EMDI resin to the inner layers(IL) were similar to that of controls bonded with 8% UF resin. In the case of the emulsified compound resin application to the all layers of particleboards, there were marked reinforcing effects of EMDI resin, although a small amount of EMDI resin was mixed with UF resin. Especially bending MOR after 24 hours cold water-immersion and thickness swelling after 2 hours hot water-immersion of compound resin-bonded particleboards were remarkably different from those of pure UF resin-bonded particleboards. It was found that separately spreading method with unemulsified EMDI resin was more effective than simultaneously spreading method with emulsified compound resin to sustain the internal bond strength of particleboards after 24 hours cold water-immersion. In the resin combination systems to outer layers/inner layers of particleboards, water resistance and strength properties were superior in order of UF+EMDI/UF+EMDI > UF/UF+EMDI > UF/UF. And water resistance of particleboards was greatly dependent upon EMDI resin level in any adhesive adding method.

• Journal of the Korean Wood Science and Technology
• /
• 제23권2호
• /
• pp.55-69
• /
• 1995

The primary objective of this research was to investigate optimum manufacturing condition of thin composite panels composed of sawdust, polyethylene film and polypropylene net. At the study the experiment was designed to make thin board in which sawdust offers effectiveness as core composing material, polyethylene as adhesive with added urea resin, and polypropylene as stiffness and flexibility in the composition panel. 100 types of thin composite panels were manufactured according to press-lam and mat-forming process of various hot pressing conditions(pressure, temperature and time). They were tested and compared with control boards on bending properties(MOR, MOE, SPL, WML), internal bond strength, thickness swelling, linear expansion and water absorption. At the same time the visual inspections of each types of panels were accomplished. The physical and mechanical properties of composite types passed by visual inspection were analyzed by Tukey's studentized range test. From the statistical analysis, the optimum manufacturing condition of thin composite panels were selected. Compared with two manufacturing processes, mat-forming process performed better than press-lam process in all tested properties. The optimum manufacturing conditions resulted from the experiment and statistical analysis were able to determine as following: the press temperature was shown the most good result at 130$^{\circ}C$ in mat forming process and 140$^{\circ}C$ press lam process, the press time 4 min in both processes, but the press pressure was 25-10kg/$cm^2$ in mat forming and 15k/$cm^2$ press lam process.

• Journal of the Korean Wood Science and Technology
• /
• 제24권2호
• /
• pp.61-70
• /
• 1996

침엽수재(針葉樹材)(Radiata pine, Pinus radiata)MDF와 활엽수재(闊葉樹材)(Rubber wood, Hevea brasiliensis)MDF 각 1종을 대상으로 MDF를 제조하기 전 원료(原料) 섬유(纖維)의 미세(微細) 구조(構造) 및 내부결합력 시험 후 MDF의 파괴면(破壞面)에서 섬유표면(纖維表面)에 접착제(接着劑)가 도포(塗布)된 형태를 주사전자현미경(走査電子顯微鏡)으로 관찰하였다. 원료 섬유는 침(針) 활엽수재(闊葉樹材) 모두 fiber twisting 및 shrinkage fold 등이 관찰되었다. 침엽수재(針葉樹材)의 경우는 유연벽공부(有緣壁孔部)에서 유연벽공(有緣壁孔)이 없는 부분에 비하여 shrinkage fold의 발생 빈도가 낮고 표면(表面) 박리(剝離)는 가도관(假導管) 중 벽공이 없는 부분에서 관찰되었다. 활엽수재(闊葉樹材) 목섬유(木纖維)는 침엽수재(針葉樹材)와 마찬가지로 shrinkage fold가 관찰되었으나 표면(表面) 박리(剝離)는 거의 관찰되지 않았다. 활엽수(闊葉樹) 섬유(纖維)에서는 벽공의 유무에 따른 shrinkage fold의 차이(差異)가 거의 관찰되지 않았는데 이는 목섬유(木纖維)가 침엽수(針葉樹) 가도관(假導管)보다 작은 단벽공(單壁孔)을 갖기 때문으로 생각된다. 또 방사유세포(放射柔細胞)와 가도관(假導管) 및 목섬유(木纖維)의 박리(剝離) 부분(部分)에는 융기부(隆起部)가 관찰되었다. 내부결합력 시험후 나타난 파괴면을 통하여 접착제 분포를 관찰한 결과 거의 모든 섬유(纖維)들이 접착제(接着劑)로 둘러싸여 있었으며 섬유(纖維)간 접착형태(接着形態)도 매우 다양하였다. 침활엽수재(針闊葉樹材)간에 강도(强度)의 차이는 있었지만 파괴(破壞) 형태(形態)는 큰 차이를 나타내지 않았다. 즉 침활엽수(針闊葉樹) 모두 접착층(接着層)이 아닌 섬유(纖維)에서 파괴(破壞)가 발생하였으며 섬유에서 박리(剝離)된, 세포벽(細胞壁)의 일부가 다른 섬유(纖維)의 표면(表面)에 남아있는 형태와 섬유(纖維) 표면(表面)에서 떨어져 나간 형태로 관찰되었다. 세포 구성이 단순한 침엽수(針葉樹) MDF에 비하여 유세포(柔細胞)와 도관(導管) 및 목섬유(木纖維)의 파편들이 활엽수(闊葉樹) MDF에서는 다양(多樣)하게 분포하였다.

• 펄프종이기술
• /
• 제29권1호
• /
• pp.7-12
• /
• 1997

This study was intended to investigate the proper shape and size of calcium carbonate for the improvement of paper properties and its end use performance. We loaded calcium carbonate of various shapes and size in the handsheet and measured their physical and optical properties. Results obtained from the study are summarized as follows : 1. Due to different particle shapes and sizes, precipitated calcium carbonate (PCC) contributed greater to bulk improvement than ground calcium carbonate (GCC). Scalenohedral form of PCC produced the bulkiest sheet, GCC made the sheet bulkier as average particle size increases. 2. Tensile strength increased as average particle size was increasing. GCC kept tensile strength more effectively than PCC. The effect of particle size on tensile strength was much more pronounced as filler addition level was increasing. 3. Over the average particle size of 6.99$\mu$m, GCC gave much higher burst strength and internal bond than PCC did. In the filler levels of 20% and 30%, GCC by using bigger size fillers showed 50~100% improvement in some cases than PCC at the same filler content. 4. Tear strength increased as average particle size was increasing. At the filler level of 30%, PCC decreased tear greatly. 5. Over the average particle size of 13.56$\mu$m, GCC kept bending stiffness greater than PCC. Due to its shape, Scalenohedral form of PCC showed higher stiffness than others at the same particle size. 6. Cubic and acicular form of PCC improved light scattering coefficient very effectively. Light scattering coefficient of GCC decreased as average particle size increased. 7. Both of particle shape and size of filler were important factor in developing optical properties and bending stiffness. Particle size was the only important factor in developing other strength properties

• Asian Journal of Atmospheric Environment
• /
• 제2권1호
• /
• pp.34-46
• /
• 2008

Emissions inputs for use in air quality modeling of Korea were generated with the emissions inventory data from the National Institute of Environmental Research (NIER), maintained under the Clean Air Policy Support System (CAPSS) database. Source Classification Codes (SCC) in the Korea emissions inventory were adapted to use with the U.S. EPA's Sparse Matrix Operator Kernel Emissions (SMOKE) by finding the best-matching SMOKE default SCCs for the chemical speciation and temporal allocation. A set of 19 surrogate spatial allocation factors for South Korea were developed utilizing the Multi-scale Integrated Modeling System (MIMS) Spatial Allocator and Korean GIS databases. The mobile and area source emissions data, after temporal allocation, show typical sinusoidal diurnal variations with high peaks during daytime, while point source emissions show weak diurnal variations. The model-ready emissions are speciated for the carbon bond version 4 (CB-4) chemical mechanism. Volatile organic carbon (VOC) emissions from painting related industries in area source category significantly contribute to TOL (Toluene) and XYL (Xylene) emissions. ETH (Ethylene) emissions are largely contributed from point industrial incineration facilities and various mobile sources. On the other hand, a large portion of OLE (Olefin) emissions are speciated from mobile sources in addition to those contributed by the polypropylene industry in point source. It was found that FORM (Formaldehyde) is mostly emitted from petroleum industry and heavy duty diesel vehicles. Chemical speciation of PM2.5 emissions shows that PEC (primary fine elemental carbon) and POA (primary fine organic aerosol) are the most abundant species from diesel and gasoline vehicles. To reduce uncertainties in processing the Korea emission inventory due to the mapping of Korean SCCs to those of U.S., it would be practical to develop and use domestic source profiles for the top 10 SCCs for area and point sources and top 5 SCCs for on-road mobile sources when VOC emissions from the sources are more than 90% of the total.

• 한국콘텐츠학회논문지
• /
• 제16권12호
• /
• pp.233-243
• /
• 2016

영화 <사도>는 사도세자의 비극적 가정사에 공감하는 관객의 감수성, 사회적 기표에 대한 관찰의 기회를 제공한다. 관객은 사도세자의 비극을 보며 아버지와 아들의 상이한 정서적 감정, 전통의 이상과 가치의 상징인 아버지의 주체와 이를 파괴하려는 저항적 주체간의 상반된 의식이 마음속에서 충돌할 때 본래적 '나'로 회귀할 것인지 아니면 자동적 사회적 행동으로서 이를 봉합할 수 있는 무의식적 위선 혹은 의식화된 감정을 따를 것인지 고민한다. 관객은 전통적 사회의 상징인 아버지의 권위와 위엄을 지향하면서도 사도세자의 비극을 보며 '나'의 존재론적 철학적 가치를 중시하는 양가적 태도, 도덕적 가치관을 내 보인다. 본 연구는 아버지의 기표와 그에 대한 '나'의 저항 그리고 '나'의 광기를 살펴보는 가운데 도덕의 가치와 기준에 관한 관객의 사유를 살펴보고, 또한 과거의 도덕은 항상 도전에 직면할 수밖에 없고, 현재 역시 미래에 의해 전복될지도 모르는 도덕의 가치에 안위하고 있기에 관객이 최상의 것이기를 원하고 믿었던 도덕, 질서, 법의 체계는 언제나 미완성이고 변화무쌍한 것임을 말하고자 한다.

• Bulletin of the Korean Chemical Society
• /
• 제32권3호
• /
• pp.981-987
• /
• 2011

The anomalous spectroscopic properties of quercetin-3-O-rhamnoside (QCRM) and quercetin-3-O-rutinoside (QCRT) in AOT reverse micelle were studied. The excited state intramolecular proton transfer (ESIPT) occurs through the strong hydrogen bond between the -OH at position 5 and the carbonyl oxygen. Because the ESIPT can only happens in the $S_1$ state and the Franck-Condon factor involved in the $S_2\;{\rightarrow}\;S_1$ internal conversion is small, the $S_2\;{\rightarrow}\;S_o$ emission alone appears. Because the molecular planarity is improved at the interior of the micelle, the excited state intramolecular charge transfer in the $S_1$ state is extended, and the excited state is more tolerable for any quenching effects in the micelle. Therefore, an $S_1\;{\rightarrow}\;S_o$ emission was newly discovered under this micelle microenvironment. For the $S_2\;{\rightarrow}\;S_o$ emission, the quantum yields increase but the quantum yield of the $S_1\;{\rightarrow}\;S_o$ emission approximately decreases as the water concentration in the micelle increases.