• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.5
• /
• pp.350-357
• /
• 2020

This study presents the design of an 18 kW two-phase interleaved buck converter that uses a coupled inductor for an electric vehicle rapid charger. The designs of a two-phase coupled inductor for current ripple and physical size reduction and a two-phase interleaved buck converter based on silicon carbide metal - oxide - semiconductor field-effect transistor for high efficiency were described in detail. The operating principle of the two-phase interleaved buck converter was analyzed, and the coupled inductor was investigated using a magnetized equivalent circuit. Simulation and experiments were conducted to verify the validity of the proposed two-phase interleaved buck converter, and the theoretical design method and experimental results were confirmed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.6
• /
• pp.547-555
• /
• 2013

This paper proposes the interleaved buck converter using a soft switching auxiliary circuit. In this scheme, an auxiliary circuit is added to the conventional interleaved buck converter and used to achieve soft-switching conditions for both the main switch and freewheeling diode. In addition, the switch in the auxiliary circuit operates under soft-switching conditions. Also, according to the input to output conditions, the main switch achieved zero-current-transition(ZCT) or zero-current & zero-voltage-transition(ZCZVT) at turn on. Thus, the proposed interleaved buck converter provides a higher efficiency. The basic operations, in this paper, are discussed and design guidelines are presented. The usefulness of the proposed converter is verified on a 200kHz, 180W prototype converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.2
• /
• pp.116-123
• /
• 2014

In this paper, a soft-switching scheme for the PWM interleaved buck converter(IBC) is newly proposed to obtain the advantages of both the conventional PWM interleaved buck and resonant converters such as ease of control, reduced switching losses and stresses, and low EMI. To obtain the soft-switching action, the proposed scheme employs an auxiliary circuit, which is added to the conventional interleaved buck converter and used to achieve soft-switching for both the main switches and the output diodes while not incurring any additional losses due to the auxiliary circuit itself. In this paper, the basic operations are discussed and design guidelines are presented. And through the experimental results, the usefulness of the proposed converter is verified.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.506-510
• /
• 2004

A multi-phase interleaved buck converter is used to reduce current ripples and filter size of a power supply. This paper addresses the modelling and steady-state analysis of the multi-phase interleaved buck converter operated in discontinuous inductor current mode. The model is derived using an averaging technique in steady state. The do voltage ratio and the range of the discontinuous inductor current mode(DICM) and the continuous output current mode(COCM) are derived from the averaged state-space model. In addition, the efficiency is investigated according to the number of phase.

• IEIE Transactions on Smart Processing and Computing
• /
• v.6 no.1
• /
• pp.47-52
• /
• 2017

Inductor in high power converter system increases production cost, volume and core loss proportional to the power. To decrease these disadvantages, this paper analyzed the characteristic of parallel-inductor and coupled-inductor in interleaved system with simulation. As a result, it is confirmed that two-phase interleaved non-coupled buck-converter has the best characteristic among three types converter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.298-308
• /
• 2017

This paper presents a Interleaved Buck Converter(IBC) system with Random PWM to reduce electromagnetic noise by harmonics. Swithced mode power supply generally controlled by high switching frequency have a electromagnetic interference(EMI) issue due to the high-voltage/high-current switching to regulate the voltage in buck converter. To solve the problem. we present a novel IBC system with PRBS. IBC system has two active switches with 180 phase difference that controll the cicuit with two PWM signal. IBC system may be disadventageous for the cost due to the addtion of one set of switch, but it has adventages of power distribution, current ripple cancellation, fast transient response, and passive component size reduction. To verify the validity of study, simulation program has been bulit using PSIM and the experimental results of IBC system using RPWM was compared with the conventinal PWM and randomized PWM.

• Journal of Power Electronics
• /
• v.5 no.2
• /
• pp.104-108
• /
• 2005

This paper presents the performance improvement of voltage-mode controlled interleaved synchronous buck converters. This is a voltage-mode controlled scheme, where the controllers do not need an external saw-tooth generator for PWM generation and the loop design is easier. The controller implementation requires only a single error amplifier and gives almost current mode control performance. The control scheme uses voltage feedback with two loops similar to current mode control: one for the slow outer loop and the other for the faster inner PWM control loop. To improve the performance of the converter system a coupled inductor is used. This coupled inductor reduces the magnetic size and also improves the converter's transient performance without increasing the steady-state current ripple. The effectiveness of the proposed control scheme is demonstrated through PSIM simulations.

• Journal of the Institute of Convergence Signal Processing
• /
• v.8 no.3
• /
• pp.199-204
• /
• 2007

This paper presents design of interleave configured dc-dc converter for high power distributed power system applications. The multi channel interleaving buck converter with small inductance has proved to be suitable for micro-grid, requiring medium output voltages, high output currents and fast transient response. Integrated magnetic components are used to reduce the size of the converter and improve efficiency. Unlike conventional methods, the distributed approach requires no centralized control, automatically accommodates varying numbers of converter cells, and is highly tolerant of subsystem failures. A general methodology for achieving distributed interleaving is proposed, along with a specific implementation approach. The design and simulation verification of switching frequency 10 kHz system is presented with interleaved clocking of the converter cells. The simulation (simulated by PSIM 6.1) results corroborate the analytical predictions and demonstrate the tremendous benefits of the distributed interleaving approach.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.2
• /
• pp.123-130
• /
• 2007

This paper presents the generalized and explicit expressions for evaluating the performance of the multi-phase interleaved buck converter (IBC) operating in discontinuous inductor current mode (DICM). The full-order averaged model is derived. The generalized transfer functions of interest are presented and the dynamic characteristics are analyzed. The generalized analysis of converter performance is verified through the experimental and simulation results.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.6
• /
• pp.16-24
• /
• 2009

In this paper, DC-DC buck converter with on-chip filter inductor and capacitor is presented. By operating at high switching frequency of 50MHz with stacked interleaved topology, we reduced inductor and capacitor sizes compared to previously published DC-DC buck converters. The proposed circuit is designed in a standard $0.5{\mu}m$ CMOS process, and chip area is $9mm^2$. This circuit operated at the input voltage of $3{\sim}5V$ range, the maximum load current of 250mA, and the maximum efficiency of 71%.