• 한국의류학회지
• /
• 제19권5호
• /
• pp.765-773
• /
• 1995

Effect of interfacial electrical conditions such as, the f potential of PET fiber and u-Fe203 particles, the stability parameter and potential energy of interaction on adhesion of a-Fe903 particles to PET fabric and their removal from the fabric, were investigated as functions of pH, electrolyte and ionic strength. The stability parameter, potential energy of interaction between a-Fe2O3 particles and PET fabric were calculated by using the heterocoagulation theory for a sphere-plate model The adhesion of a-Fe2O3 particles to PET fabric and their removal from PET fabric were carried out by using water bath shaker and Terg-O-Tometer under various solution conditions. The adhesion of a-Fe2O3 particles to the PET fabric and the removal of a-Fe2O3 particles from the PET fabric were biphasic and were maximum and minimum at pH 7~8, respectively. With high pH and polyanion electrolytes in solution, the adhesion of a-Fe2O3 particles to the PET fabric was low but effects of electrolytes on the removal of a-Fe2O3 particles from the PET fabric was small. The adhesion of a-Fe2O3 particles to the PET fabric and the removal of a-Fe2O3 Particles from the PET fabric were biphasic, and were lowest and highest at the ionic strength 1$\times$10-3, respectively. The adhesion of a-Fe2O3 particles to PET fabric was well related with the interfacial electrical conditions; it was negatively correlated with the f potentials of a-Fe2O3 Particles of its absolute value, the stability parameter and the maximum of total potential energy, while, the adhesion was not related with the t potentials of PET fiber itself. Therefore, the primary factor determining the adhesion of a-Fe203 particles to PET fabric may be the stability of dispersed particles caused by the electrical repulsion of particles. The removal of a-Fe203 particles from PET fabric was not related to such interfacial electrical conditions as the t potentials of PET fiber, the stability parameter and the maximum of total potential energy but removal was related to t potential of a-Fe203 particles.

• 마이크로전자및패키징학회지
• /
• 제18권4호
• /
• pp.11-18
• /
• 2011

3차원 칩 적층 접합에 사용하기 위한 Cu-Cu 금속 저온 접합 공정을 위하여 접합 온도 및 플라즈마 표면 전처리에 따른 열 압착 접합을 수행 하였다. 4점굽힘시험과 CCD 카메라를 이용하여 Cu 접합부의 정량적인 계면접착에너지를 평가하였다. 접합 온도 $250^{\circ}C$, $300^{\circ}C$, $350^{\circ}C$에서 각각 $1.38{\pm}1.06$(상한값), $7.91{\pm}0.27$(하한값), $10.36{\pm}1.01$(하한값) $J/m^2$으로 접합온도 $300^{\circ}C$ 이상에서 계면접착에너지 5 $J/m^2$ 이상의 값을 얻었다. 접합 온도 $300^{\circ}C$ 이하 낮은 온도에서 접합하기 위해 Cu-Cu 열 압착 접합 전 Ar+$H_2$ 플라즈마로 $200^{\circ}C$에서 2분간 표면 전처리 후 $250^{\circ}C$ 조건에서 열 압착 접합할 경우 계면접착에너지 값이 $6.59${\pm}0.03$(하한값) $J/m^2$로 표면 전 처리하지 않은 시험편에 비해 접합 특성이 크게 증가 하였다.

• 마이크로전자및패키징학회지
• /
• 제14권1호
• /
• pp.61-68
• /
• 2007

임베디드 PCB 기판내 유전체 재료인 Atomic Layer Deposition(ALD) $Al_2O_3$ 박막과 전극재료인 스퍼터 증착된 Cu박막 사이의 계면접착력을 $90^{\circ}$ 필 테스트방법으로 측정하여 순수 빔 굽힘을 가정한 에너지 평형 해석을 통하여 계면파괴에너지를 구하였다. $Cu/Al_2O_3$의 계면파괴에너지(${\Gamma}$)는 매우 약하여 측정할 수 없었으나, 접착력 향상층 Cr 박막을 삽입하여 $Cr/Al_2O_3$의 계면파괴에너지는 $10.8{\pm}5.5g/mm$를 얻었다. $Al_2O_3$ 표면에 $0.123W/cm^2$ 의 power density로 2분간 $Ar^+$ RF 플라즈마 전처리를 하고 Cr박막을 삽입한 $Cr/Al_2O_3$ 계면파괴에너지는 $39.8{\pm}3.2g/mm$으로 매우 크게 증가하였는데, 이는 $Ar^+$ RF 플라즈마 전처리에 따른 mechanical interlocking효과와 Cr-O 화학결합 효과가 동시에 기여한 것으로 생각된다.

• 접착 및 계면
• /
• 제4권1호
• /
• pp.1-8
• /
• 2003

본 연구에서는 이관능성 에폭시와 PMR-15 블렌드계의 접촉각 측정과 파괴인성 측정을 통하여 PMR-15 조성비에 따른 표면자유에너지가 기계적 계면특성에 미치는 영향에 대하여 고찰하였다. 블렌드계의 FT-IR 분석 결과, PMR-15의 이미드화에 따른 특성 밴드가 1,722, $1,778cm^{-1}$ (C=O)와 $1,372cm^{-1}$ (C-N)에서 나타났고, 에폭시의 개환 반응에 따른 -OH peak는 PMR-15 phr의 함량에서 가장 크게 나타나는 것을 확인할 수 있었다. 증류수와 diiodomethane을 젖음액으로 사용하여 sessile drop 방법으로 접촉각을 측정한 결과, 표면자유에너지는 극성 요소의 증가에 의해서 PMR-15의 함량이 10 phr일 때 최고값을 나타내었다. 또한, 기계적 계면특성을 파괴인성 측정을 통하여 알아본 결과 $K_{IC}$와 $G_{IC}$ 또한 표면자유에너지와 유사한 경향을 나타내는 것을 알 수 있었는데, 이는 PMR-15 10 phr의 조성에서 수소결합의 증가에 의한 블렌드계의 극성요소가 증가함에 따라 분자들간의 계면결합력이 증가했기 때문인 것으로 관찰된다.

• 마이크로전자및패키징학회지
• /
• 제28권2호
• /
• pp.29-37
• /
• 2021

3 차원 패키징을 위한 저온 Cu-Cu직접 접합부의 계면접착에너지를 향상시키기 위해 Cu박막 표면에 대한 Ar/N₂ 2단계 플라즈마 처리 전, 후 Cu표면 및 접합계면에 대한 화학결합을 X-선 광전자 분광법(X-ray photoelectron spectroscopy)을 통해 정량화한 결과, 2단계 플라즈마 처리로 인해 Cu표면에 Cu₄N이 형성되어 Cu산화를 효과적으로 억제하는 것을 확인하였다. 2단계 플라즈마 처리하지 않은 Cu-Cu시편은 표면 산화막의 영향으로 접합이 제대로 되지 않았으나 2단계 플라즈마 처리한 시편은 효과적인 표면 산화방지효과로 인해 양호한 Cu-Cu접합을 형성하였다. Cu-Cu직접접합 계면의 정량적 계면접착에너지를 double cantilever beam 시험방법 및 4점 굽힘(4-point bending, 4-PB) 시험방법을 통해 비교한 결과, 각각 1.63±0.24, 2.33±0.67 J/m²으로 4-PB 시험의 계면접착에너지가 더 크게 측정되었다. 이는 계면파괴역학의 위상각(phase angle)에 따른 계면접착에너지 증가 거동으로 설명할 수 있는데 즉, 4-PB의 계면균열선단 전단응력성분 증가로 인한 계면거칠기의 효과에 기인한 것으로 판단된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.968-970
• /
• 1999

The trend of increasing of portable electric devices and demand for global environmental conservation have demands the development of high energy density rechargeable batteries. Lithium polymer battery has excellent theoretical energy density and energy conversion efficiency. Lithium polymer battery, included solid polymer electrolyte(SPE), can be viewed as a system suitable for wide applications from thin film batteries for microelectronics to electric vehicle batteries. The purpose of this paper is to research and development of flyash anode for lithium polymer battery. We investigated AC impedance response and charge/discharge characteristics of flyash/SPE/Li cells. The radius of semicircle associated with the interfacial resistance of flyash/SPE/Li cell increased very slowly during discharge process from 3.11V to 0.478V. And then the cell resistance was decreased at discharge process from 10% SOC to 0% SOC. Also, The radius of semicircle associated with the interfacial resistance of flyash/SPE/Li cell decreasing very slowly during charge process. And then the cell resistance was increased after 20th discharge precess. The discharge capacity based on flyash of 1st and 20th cycles was 276mAh/g and 143mAh/g.

• Nuclear Engineering and Technology
• /
• 제29권1호
• /
• pp.45-57
• /
• 1997

The direct contact condensation phenomenon, which occurs when steam is injected into the subcooled water, has been experimentally investigated. Two plume shapes in the stable condensation regime are found to be conical and ellipsoidal shapes depending on the steam mass flux and the liquid subcooling. Divergent plumes, however, are found when the subcooling is relatively small. The measured expansion ratio of the maximum plume diameter to the injector inner diameter ranges from 1.0 to 2.3. By means of fitting a large amount of measured data, an empirical correlation is obtained to predict the steam plume length as a function of a dimensionless steam mass flux and a driving potential for the condensation process. The average heat transfer coefficient of direct contact condensation has been found to be in the range 1.0~3.5 ㎿/$m^2$.$^{\circ}C$. Present results show that the magnitude of the average condensation heat transfer coefficient depends mainly on the steam mass fin By using dynamic pressure measurements and visual observations, six regimes of direct contact condensation have been identified on a condensation regime map, which are chugging, transition region from chugging to condensation oscillation, condensation oscillation, bubbling condensation oscillation, stable condensation, and interfacial oscillation condensation. The regime boundaries are quite clearly distinguishable except the boundaries of bubbling condensation oscillation and interfacial oscillation condensation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.61-61
• /
• 2010

In the present work, we present the optimized the hybrid structures of carbon nanotubes (CNTs) and metal nanocomposites including Cu, Al, Co and Ni using the first principle calculations based on the density functional theory. Introduction of CNTs into a metal matrix has been considered to improve the mechanical properties of the metal matrix. However, the binding energy between metals and pristine CNTs wall is known to be so small that the interfacial slip between CNTs and the matrix occurs at a relatively low external stress. The application of defective or functionalized CNTs has thus attracted great attention to enhance the interfacial strength of CNT/metal nanocomposites. Herein, we design the various hybrid structures of the single wall CNT/metal complexes and characterize the interaction between single wall CNTs and various metals such as Cu, Al, Co or Ni. First, differences in the binding energies or electronic structures of the CNT/metal complexes with the topological defects, such as the Stone-Wales and vacancy, are compared. Second, the characteristics of functionalized CNTs with various surface functional groups, such as -O, -COOH, -OH interacting with metals are investigated.We found that the binding energy can be enhanced by the surface functional group including oxygen since the oxygen atom can mediate and reinforce the interaction between carbon and metal. The binding energy is also greatly increased when it is absorbed on the defects of CNTs. These results strongly support the recent experimental work which suggested the oxygen on the interface playing an important role in the excellent mechanical properties of the CNT-Cu composite[1].

• 접착 및 계면
• /
• 제22권4호
• /
• pp.113-117
• /
• 2021

차세대 태양전지 중 유기물을 활용하는 유기 태양전지는 미래 핵심 에너지 생산 장치로, 최근 급격한 성장세와 함께 많은 주목을 보이고 있다. 유기 태양전지 효율 향상을 위해서 계면 공학 기술이 많이 응용되고 있다. 특히 양전극인 양극과 음극에 계면 공학을 활용하여 에너지 준위 조절을 통한 소자 효율 향상과, 궁극적으로 적층형 유기 태양전지에 계면 공학을 활용하여 우수한 전기적, 광학적 성능을 이끌어 내어 고성능 소자를 제작하는 방식이 널리 활용되고 있다. 본 총설에서는 유기태양전지에 활용되고 있는 계면 공학에 대하여 최근 연구 동향을 요약 및 소개하고 고성능 유기 태양전지 제작 방식에 대하여 논의하고자 한다.

• Journal of Electrochemical Science and Technology
• /
• 제9권4호
• /
• pp.330-338
• /
• 2018

The adhesion strength as well as the electrochemical properties of $LiNi_{0.4}Mn_{0.4}Co_{0.2}O_2$ electrodes containing various conductive carbons (CC) such as fiber-like carbon, vapor-grown carbon fiber, carbon nanotubes, particle-like carbon, Super P, and Ketjen black is compared. The morphological properties is investigated using scanning electron microscope to reveal the interaction between the different CC and the active material. The surface and interfacial cutting analysis system is also used to measure the adhesion strength between the aluminum current collector and the composite film, and the adhesion strength between the active material and the CC of the electrodes. The results obtained from the measured adhesion strength points to the fact that the structure and the particle size of CC additives have tremendous influence on the binding property of the composite electrodes, and this in turn affects the electrochemical property of the configured electrodes.