• 천문학회지
• /
• 제25권2호
• /
• pp.111-128
• /
• 1992

Infrared emissions from spherical dust, clouds are calculated using quasi-diffusion method. We have employed graphite-silicate mixture with power-law size distribution for the dust model. The grains are assumed to be heated and cooled by radiative processes only. The primary heating source is diffuse interstellar radiation field. hut the cases with an embedded source are also considered. Since graphite grains have higher temperature than silicate grains, the observed IR emission is mainly due to graphite grains, unless the fraction of graphite grains is negligibly small. The color temperature of Bok globules obtained from IRAS 60 and $100{\mu}m$ data are found to be consistent with the dust cloud with graphite-silicate mixture exposed to average interstellar radiation field. The color temperature is sensitive to the external radiation field, but rather insensitive to the size distribution of the grains. We found that the density distribution can be recovered outside the beam size using the inversion technique that assumes negligible optical depth. However, the information within the beam size is lost for if beam convolved intensity distributions are used in deriving density profile.

• 한국환경보건학회지
• /
• 제36권4호
• /
• pp.264-270
• /
• 2010

Agricultural workers are often exposed to high levels of dust during field operations. A systematic exposure assessment of annual task-weighted exposure has not been thoroughly examined. The occupational dust exposure in two wine grape vineyards was measured. Exposure levels to total and respirable dust were determined for a 1-year cycle of work. An operation profile including the frequency of tasks was established. The means of total and respirable dust exposure were $1.08\;mg/m^3$ and $0.07\;mg/m^3$, respectively. Based on the exposure for each task and the task frequency, task-weighted mean exposures to total and respirable dust were estimated as $1.115\;mg/m^3$ and $0.079\;mg/m^3$, respectively. The task-weighted exposure was significantly represented by three operations and could be attributed to the exposure frequency rather than the exposure intensity of operations. The measurement of a few of the most frequent tasks may be an alternative method of estimating task-weighted exposure. Agricultural dust exposure can be significantly reduced by targeting those tasks most important to task-weighted dust exposure.

• 한국의류산업학회지
• /
• 제16권2호
• /
• pp.319-325
• /
• 2014

This article describes a method for producing chitosan non-woven fabrics by just hot pressing without the use of a binder. A study has been made of the wet spinning of chitosan fiber. The fibers were rinsed thoroughly in running water and chopped wet into staples of with a length of approximately 5-10 mm. The chopped chitosan staples were dispersed uniformly in water and fabricated using a non-woven making machine. This study examined the formation and the characteristics of chitosan non-woven fabrics manufactured by hot pressing without the use of a binder. The effects of the non-woven fabrication conditions on the thermal, morphological, structural, and physical properties of chitosan non-woven fabric with and without water as a plasticizer were studied. The temperature of the exothermic peak, decomposition of chitosan fibers increased with increasing heating rate. Water in the chitosan fiber effectively plasticized the chitosan fiber. The thermal bonded structure of the wet chitosan fiber with water as a plasticizer was clearly found in many parts of the non-woven fabric at a fabrication temperature of $200^{\circ}C$. The intensity and profile of the (100) plane($2{\theta}=10.2^{\circ}$) and (040) plane($2{\theta}=20.9^{\circ}$) in the chitosan non-woven fabric decreases and became smooth in the non-woven fabric formation by melting.

• 대한기계학회논문집B
• /
• 제25권11호
• /
• pp.1476-1482
• /
• 2001

Turbulent boundary layer over a flat plate was disturbed by installing an elliptic cylinder with an axis ratio of AR=2. For comparison, the same experiment was carried out for a circular cylinder having the same vertical height. The surface pressure and the heat transfer coefficient on the flat plate were measured with varying the gap distance between the elliptic cylinder and the flat plate. The mean velocity and the turbulent intensity profile of the streamwise velocity component were measured using a hot-wire anemometry. As a result, the flow structure and the local heat transfer rate were modified by the interaction between the cylinder wake and the turbulent boundary layer as a function of the critical gap ratio where the regular vortices start to shed. For the elliptic cylinder, the critical gap ratio is increased and the surface pressure on the flat plate is recovered rapidly at downstream location, compared with the equivalent circular cylinder. The maximum heat transfer rate occurs at the gap ratio of G/B = 0.5, where the flow interaction between the lower shear layer of the cylinder wake and the turbulent boundary layer is strong.

• 대한기계학회논문집
• /
• 제9권4호
• /
• pp.403-413
• /
• 1985

본 논문에서는 수직벽 하류에 형성되는 박이 전단층의 발전과 재부착 그리고 재발전 경계층에 대해 평균 속도, 벽면의 압력 분포, 난류 강도, 레이놀즈 전단 압력 및 아직 수직벽에 대해서는 보고된바 없는 난류 떨림 속도 성분들의 3승곱 통계치를 측정하여 난류 구조의 변화를 분석하고 이를 수치적 계산 모델개발의 자 료로 제공하고자 함이 이 연구의 목적이다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.287-294
• /
• 2005

Flow rate measurement uncertainties of the ultrasonic flow meter are generally influenced by many different factors, such as Reynolds number, flow distortion, turbulence intensity, wall surface roughness, velocity integration method along the acoustic paths, and transducer installation method, etc. Of these influencing factors, one of the most important uncertainties comes from the velocity integration method. In the present study, a optimization weighting factor method for 5-chord, which is given by a function of the chord locations of acoustic paths, is employed to obtain the mean velocity in the flow through a pipe. The power law profile is assumed to model the axi-symmetric pipe flow and its results are compared with the present weighting factor concept. For an asymmetric pipe flow, the Salami flow model is applied to obtain the velocity profiles. These theoretical methods are also compared with the previous Gaussian, Chebyshev, and Tailor methods. The results obtained show that for the fully developed turbulent pipe flows with surface roughness effects, the present weighting factor method is much less sensitive than Chebyshev and Tailor methods, leading to a better reliability in flow rate measurement using the ultrasonic flow meters.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제32회 KOSCO SYMPOSIUM 논문집
• /
• pp.149-156
• /
• 2006

Structure of edge flame established in a mixing layer, formed between two uniformly flowing pure $CH_4$ and pure $O_2$ streams, is numerically investigated by employing a detailed methane-oxidation mechanism. The numerical results exhibited the most outstanding distinction of using pure oxygen in the fuel-rich premixed-flame front, through which the carbon-containing compound is found to leak mainly in the form of CO instead of HC compounds, contrary to the rich $CH_4-air$ premixed flames in which $CH_4$ as well as $C_2H_m$ leakage can occur. Moreover, while passing through the rich premixed flame, a major route for CO production, in addition to the direct $CH_4$ decomposition, is found to be $C_2H_m$ compound formation followed by their decomposition into CO. Beyond the rich premixed flame front, CO is further oxidized into $CO_2$ in a broad diffusion-flame-like reaction zone located around moderately fuel-rich side of the stoichiometric mixture by the OH radical from the fuel-lean premixed-flame front. Since the secondary CO production through $C_2H_m$ decomposition has a relatively strong reaction intensity, an additional heat-release branch appears and the resulting heat-release profile can no longer be seen as a tribrachial structure.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.610-614
• /
• 1996

Sealing of lubricat-air mixture in the high performance machining conte is one of most the important characteristics to carry out enhanced lubrication. High speed spindle requires non-contact type of sealing mechanism. Evaluating an optimum seal design to minimize leakage is concerned in the aspect of flow control. Effect of geometry and leakage path are evaluated according to variation of sealing geometry, Velocity, pressure, turbulence intensity of profile is calculated to fina more efficient geometry and variables. This offers a methodological way of enhancement seal design for high speed spindle. The working fluid is regarded as two phases that are mixed flow of oil phase and air phase. It is more reasonable to simulate an oil jet or oil mist type high speed spindle lubrication. Turbulence and compressible flow model are used to evaluate a flow characteristic, This paper arranges a geometry of mostly used non-contact type seal and analyzes leakage characteristics to minimize a leakage on the same sealing area.

• 한국레이저가공학회지
• /
• 제14권1호
• /
• pp.1-5
• /
• 2011

Photo-induced gratings m flexible PDMS (polydimethly siloxane) film are directly written by a high-intensity femtosecond (130fs) Ti: Sapphire laser (${\lambda}_p$ = 800nm). The refractive index modifications with $4\;{\mu}m$ diameters were photo-induced after the femtosecond irradiation with peak intensities of more than $1{\times}10^{11}W/cm^2$. The graded refractive index profile was fabricated to be a symmetric around the center of the point at which femtosecond laser by controlling both laser power and focused depth. The change on refractive index in the laser-modified regions was estimated to be approximately $10^{-3}$. The internal flexible symmetric diffraction gratings in PDMS film was successfully fabricated using a femtosecond laser.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.44-46
• /
• 2005

Data storage related with writing and retrieving requires high storage capacity, fast transfer rate and less access time. Today any data storage system cannot satisfy these conditions, however holographic data storage system can perform faster data transfer rate because it is a page oriented memory system using volume hologram in writing and retrieving data. System can be constructed without mechanical actuating part therefore fast data transfer rate and high storage capacity about $1Tb/cm^3$ can be realized. In this paper, to reduce errors of binary data stored in holographic data storage system, a new method for bit error reduction is suggested. We proposal Algorithm use The Extended Kalman filter. The Kalman filter reduce measurement noise. Therefore, By using this error reduction method following results are obtained; the effect of measurement nois of Pixel is decreased and the intensity profile of data page becomes uniform therefore the better data storage system can be constructed.