• 대한기계학회논문집B
• /
• 제31권5호
• /
• pp.405-415
• /
• 2007

The effects of recirculated exhaust gas on exhaust emissions under four kinds of nozzle tip with the different fuel consumption rates are experimentally investigated by using an once-through boiler with a FGR system. The purpose of this study is to develop the FGR control system for reducing $NO_x$ emissions in boilers. Intake and exhaust oxygen concentrations, and equivalence ratio are considered to figure out the effect of FGR rate on exhaust emissions at various fuel consumption rates. It is found that $NO_x$ emissions are markedly decreased, while soot emissions are increased owing to the drop of intake and exhaust oxygen concentrations, and the rise of equivalence ratio as FGR rates are elevated. One can also conclude that the reduction in $NO_x$ emissions is more considerably influenced by the variation of equivalence ratio due to the FGR rate than the fuel consumption rate.

• Architectural research
• /
• 제19권4호
• /
• pp.101-108
• /
• 2017

The use of the air conditioner is increasing due to the rise of the outdoor temperature during summer, and the problems of the fire and the cooling performance deterioration are caused due to lack of maintenance of the outdoor unit. In particular, overall performance of cooling system and efficiency in outdoor units have been degraded due to an intake of high-temperature outdoor air thereby increasing cooling energy and operating cost. Thus, this study aimed to increase efficiency of outdoor units by evaporating and cooling intake air through mist spray at the intake port surface in the outdoor unit. The measurements results showed that total power consumption of misting outdoor unit compared to that of conventional outdoor units was reduced by 21% approximately, and total power consumption of the entire system including pump was reduced by 16.7%. In addition, the operating cost including water use was reduced by 13.5% approximately. In summary, if a mist-spray nozzle kit is installed in air-cooled outdoor units, the reduction in the usage of cooling energy and operating cost will be achieved without replacement of existing cooling systems or a large scale of repairs.

• 한국자동차공학회논문집
• /
• 제8권5호
• /
• pp.36-46
• /
• 2000

The performance improvement and emission reduction in a turbocharged D.I. diesel engine was studied experimentally in this paper. The system of intake port, fuel injection and turbochager are very important factors which have influence on the engine performance and exhaust emission because the properties in the injected fuel depend on the combustion characteristics. Through these experiments it can be expected to meet performance and emission by optimizing the main parameters; the swirl ratio of intake port, fuel injection system and turbocharger. The swirl ratio of intake port was modified by hand-working and measured by impulse swirl meter. Through this steady flow test, we knew that the increase of swirl ratio is decreasing the mean flow coefficient, whereas the gulf factor is increasing. And the optimum results of engine performance and emission are as follows; the swirl ratio is 2.43, injection timing is BTDC 13。 CA, compression ratio is 16, combustion bowl is re-entrant 5$^{\circ}$, nozzle hole diameter is $\Phi$0.28＊6, turbocharger is GT40 model which are compressor A/R 0.58 AND turbine A/R 1.19.

• 한국공작기계학회논문집
• /
• 제14권6호
• /
• pp.88-94
• /
• 2005

A swirl ratio of a charge in the cylinder could be calculated by measuring both the rotary speed of paddle and the intake air flow rate in the swirl measurement apparatus fur several positions of valve lift. The automation of the swirl ratio measurement for a cylinder head is achieved by controlling both the valve lift of cylinder head and a suction pressure of the surge tank, instead of controlling them manually. PID control of the surge tank pressure and positioning a valve lift of the cylinder head are also achieved by using two step motors, respectively. Rotating speed of a paddle are measured using an optical sensor and a counter. Flow rate are measured from ISA 1932 flow nozzle by reading a differential pressure gauge position using IEEE-1394 camera. Time to measure the swirl ratio for a port in the cylinder head is drastically reduced from an hour to 3 minutes by automation control of the apparatus.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.182-189
• /
• 2005

In order to investigate the effect of premixed gasoline, diesel fuel, and n-heptane charges on the combustion and exhaust emission characteristics in a direct injection (DI) diesel engine, the experimental studies are performed. The premixed fuels are injected into the premixing chamber that installed upstream of the intake port in order to minimize the inhomogeneity effect of premixed charge. The injection nozzle for directly injected fuel is equipped in the center of the combustion chamber. The air temperature control system is equipped in the intake manifold to examine the effect of air temperature. The experimental results of this study show premixing fuel is effective method to reduce the NOx and soot emissions of diesel engine. NOx emissions are linearly decreased with increasing premixed ratio for the three kinds of premixed fuels. The heating of intake air $(80^{\circ}C)$ reduced the deterioration of BSFC in high premixed ratio, because it promotes evaporation of premixed diesel droplet in the premixing chamber.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.135-144
• /
• 2005

The Effects of intake swirl and combustion parameters on the performance and emission characteristics in a V8 type turbocharged intercooler D.I. diesel engine of the displacement $16.7\iota$ were studied experimentally in this paper. Generally the swirl in the combustion process of diesel engine promotes mixing of the injection fuel and the intake air. Also, TCI diesel engine is put to practically use intercooler in order to increase boost efficiency which is cooled boost air. As a result of steady flow test, when the swirl ratio is increased, the mean flow coefficient is decreased, whereas the Gulf factor is increased. And through engine test, its can be effected to meet performance and emission by optimizing the main parameters; the swirl ratio is 2.25, compression ratio is 17.5, combustion bowl is re-entrant $8.5^{\circ}$, nozzle hole diameter is $\phi0.33^{\ast}3+\phi0.35^{\ast}2$, injection timing is BTDC $12^{\circ}CA$ and turbocharger is T02 model which are compressor 0.6A/R+46trim and turbine 1.0A/R+57trim.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.590-593
• /
• 2009

모델 스크램제트 엔진의 3차원 유동특성 이해를 위하여 다단의 충격파를 발생 시키는 흡입구부터(외부 유동영역) 공동형 보염기, 연소기, 노즐이 포함되는 엔빈 내부 전영역을 통합한 수치해석을 수행하였다. $k-{\omega}$ SST 난류모델과 Sarkar모델이 적용된 저 레이놀즈 수 k-e 난류모델의 해석결과를 실험 결과와 비교하였으며, 흡입구의 측면효과(intake side wall effects)를 살펴보기 위하여 측면의 유무에 따른 유동특성을 관찰하였다. 본 연구에 소요되는 계산시간의 효율성을 위하여 계산영역을 다중블럭으로 구성하였으며, MPI(Massage Passing Interface) 병렬 계산 기법을 적용하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.88-92
• /
• 2009

초음속 추진기관은 기계적인 압축기를 통해 흡입공기를 압축하는 방식이 아니라 램 압축 현상을 이용하여 흡입공기를 압축하기 때문에 흡입구에서의 전압력 회복율이 초음속 추진기관 전체의 작동특성에 결정적인 영향을 주게 된다. 제어기 설계에 앞서 엔진의 동특성 해석을 수행한 결과 비행체의 받음각이 커질수록 버즈마진 값이 작아져 일부영역에서는 충격파가 흡입구 외부에서 발생하게 됨을 확인할 수 있었다. 따라서 흡입구 내의 충격파 특성이 성능요구조건을 만족할 수 있도록 버즈마진을 제어하기 위한 PID 제어알고리즘을 설계하였다. 제어변수는 연료유량과 노즐 목면적이며 버즈마진 값이 양의 값을 갖도록 PID 제어기를 설계하였다.

• 한국분무공학회지
• /
• 제14권4호
• /
• pp.147-152
• /
• 2009

Since a liquid-phase LPG injection system allows accurate control of fuel injection and increase in volumetric efficiency, it has advantages in achieving higher engine power and lower emissions compared to the mixer type LPG supplying system. However, this system also leads to an unexpected event called icing phenomenon which occurs when moisture in the air near the injector freezes and becomes frost around the nozzle hole due to extraction of heat from surrounding caused by instant fuel vaporization. As a result, it becomes difficult to control air/fuel ratio in engine operation, inducing exacerbation of engine performance and HC emission. One effort to mitigate icing phenomenon is to attach anti-icing injection tip in the end of nozzle. Therefore, in this study, the effect of engine operation parameters as well as surrounding conditions on icing phenomenon was investigated in a bench test rig with commercially-used anti-icing injection tips. The test results show that considerable ice was deposited on the surface near the nozzle hole of the anti-icing tip in low rpm and low load operating conditions in ambient air condition. This is because acceleration of detachment of deposited ice from the tip surface was induced in high load, high rpm conditions, resulting in decrease in frost accumulation. The results of the bench testing also demonstrate that little or no ice was formed at surrounding temperature below a freezing point since the absolute amount of moisture contained in the intake air is too small in such a low temperature.

• 한국추진공학회지
• /
• 제26권5호
• /
• pp.63-73
• /
• 2022

국내 설비를 활용하여 실기체급 비행체 모델에 대한 M4 준자유류 시험을 수행하였다. 시험장치 및 비행체 모델은 반복적인 전산유체해석을 통해 통합적으로 설계/제작되었고, 해당 설비를 목표 시험 조건까지 가동하여 시험장치의 M4 노즐이 완전히 팽창하는 것을 확인하였다. 비행체 모델의 흡입구 주변의 가시화 영상을 획득하여 경사충격파가 생성되면서 비행체의 흡입구가 시동하는 것을 관측하였다. 비행체의 가변노즐을 구동하여 배압을 조절하면서 비행체 내부 유로의 벽면 압력 분포를 획득하였고, 연소기 내 화염안정화장치에서 점화용 토치 점화 및 점화보조제의 연소 현상을 관측하였다.