• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 학술대회 논문집
• /
• pp.315-319
• /
• 2004

This paper presents the integrity evaluation method of the windings in cast resin transformers using vertical thermal distribution analysis. The method is to compare the temperature distribution in a sound condition specimen with that in the failure condition specimen layer-shorted by accelerated testing. The temperature distribution was acquisited by a infrared thermography system, and the Arrhenius equation was adopted to the accelerated testing. The proposed method may be available to detect the failures in cast resin transformers.

• 한국조명전기설비학회지:조명전기설비
• /
• 제9권5호
• /
• pp.71-79
• /
• 1995

This paper describes the design and implementation of dryer controller using the dual processor. This system has higher performance of system recovery from the noise than the existing single processor dryer. And in this paper temperature control method of Dryer using on-off fuzzy logic is proposed to improve the overshoot of temperature in dryer. Experimental results shows that the performance of fuzzy controller is better than that of controller based upon on-off control method.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1989년도 추계학술발표회논문집
• /
• pp.19-24
• /
• 1989

The electron energy distribution function in mercury discharge positive columns are calculated numerically from the Boltzmann eqation under a set of parameters, such as the electron temperature to. the atomic temperature Tw. the electron number density no. and the electric field E. Especially, using the approximation that collision cross sections only depend on the energy, the calculated electron energy distribution function was shown that it falls off rapidly in the high energy tail.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 추계학술대회 논문집
• /
• pp.55-58
• /
• 2009

화석연료의 문제점을 보완하고 있는 태양광발전 시스템은 태양전지 모듈의 온도에 따라 출력량이 급격히 변화하는 특성을 가지고 있다. 이러한 특성을 잘 이해하고 전력생산을 극대화 하기위해 태양전지의 온도를 낮추기 위한 방법을 고려하였다. 본 논문에서는 모듈의 전면과 후면에 똑같은 온도 감소 설비를 한 후 전 후면의 온도를 동시에 낮추는 것이 발전량에 더 큰 도움을 준다는 결론을 도출하였다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 춘계학술대회 논문집
• /
• pp.85-88
• /
• 2007

A number of R, G and B LEDs for reference color temperature mixing ratio of RGB was determined by the theory of RGB mixing as a baseline. Once the number of LEDs was determined the objective color temperature from baseline has been achieved by the control the RGB duty ratio. And a practical prototype of 50W floodlighting adjusted by the above algorithm. The micro controller was developed with control algorithm for RGB duty ratio to obtain the objective color temperature. Detailed experiments to optimize algorithm of duty ratio and color temperature will be discussed in this paper as well.

• 조명전기설비학회논문지
• /
• 제27권12호
• /
• pp.109-113
• /
• 2013

In order to avoid the electrical fire, AFCI(Arc Fault Cirruit Interrupter) has been obligated to be adopted in the United States of America since 2002. AFCI using line resistor of neutral trace needs to compensate the variation of the line resistance by temperature variation. In this paper, the ASIC including the temperature compensation circuit is implemented. The proposed implementation is verified by showing the effectiveness of an electric and a temperature characteristics for Arc signals by simulation results.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.3-6
• /
• 2008

The purpose of this study is to investigate the luminous environment of fluorescent lamp and LED lamp in a office space for various color temperature by subject response test. For this, three different color temperatures were tested for the same illuminance level. Based on such test results for various color temperatures of fluorescent lamp and white LEDs, this study is to analyze the preferences of color temperature and light source, and perceptional brightness of each light source and color temperature. Then, this study is to derive the guidelines for the performance of color temperature which are suitable on the purpose and the mood of a office space.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.99-105
• /
• 2009

This research presents the method to decide proper locations for destressing of CWR using a non-destructive equipments to measure the longitudinal force(installation temperature) in CWR. The effect and necessity of destressing were analyzed by estimating changes of longitudinal force. The installation temperature was measured to find changes of longitudinal force in high speed and conventional lines before and after destressing or track maintenance at the locations where destressing was planed or where change of longitudinal force was expected during track maintenance. Past destressing was carried out within qualitative decision criteria. This research proposes the quantitative criteria to decide the priority order of the destressing locations reasonably by considering the difference of air temperature and stress free temperature during the track maintenances, the grade of ballast resistance force recovering and the length of destressing, etc.

• 조명전기설비학회논문지
• /
• 제28권11호
• /
• pp.26-32
• /
• 2014

In electrolysis smelting plants that using high DC current, the bus bar is most important facility for delivering the high current. The copper made bus bar is widely used for various advantages as good electrical and thermal conductivity, resonable malleability, ductility, and not rust easily. However, when high current in copper bus bar, temperature rises and maximum allowable current capacity is restricted by temperature of bus bar. In this paper, we investigated temperature variation of copper bus bar by putting cooling water channel imposed to bus bar construction. For the validity, various simulations were carried out.

• 조명전기설비학회논문지
• /
• 제25권11호
• /
• pp.33-38
• /
• 2011

In this paper, the effect of pulse current and generated heat on characteristics of the LED is measured and evaluated. For experiments, the LED driving circuit and digital logic which determines period and duty ratio of lighting are designed. At rated current, the temperature and optical characteristics of the LED with change in duty ratio and period are compared, and those of the LED with change in duty ratio and existence of cooling fan are also compared at constant average current. As a result, frequency does not affect device temperature and optical characteristic of the LED but duty ratio does. Also, the cooling fan is less effective on those of the LED at rated current.