• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.4
• /
• pp.28-35
• /
• 2007

In this paper, a study was made of the technology used to measure the remaining amount of energy in secondary cells, for which demand is ever increasing. First, the standard data were stored for measurement of the remaining energy and a compare/analysis algorithm was developed. Next, hardware was designed and a prototype that can display the SOC(State Of Charge) through an LCD displayinstrument was created. The small size of the prototype allows it to be portable and its performance is within ${\pm}4$[%].

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.126-129
• /
• 2008

최근 들어 기존 조명기구를 대신하여 LED 조명기구가 크게 각광을 받고 있다. 이는 LED의 장점인 낮은 소비전력과 긴 수명 때문인 것으로 생각된다. 하지만, 빛을 확산시켜야 하는 조명관점에서 본다면 LED 조명기구에도 개선해야 할 부분도 많아지는 것도 사실이다. 본 논문에서는 LED 조명기구에서 빛의 확산을 위해 사용되어지는 고가의 반사판에 대해 실제 개발된 조명기구의 배광곡선 분석과 시뮬레이션을 통해 확산효과를 면밀히 분석함으로써 향후 LED 조명기구의 설계에 있어서 기술 및 경제적 관점에서 도움을 주고자 한다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.17-20
• /
• 2008

본 논문에서는 After-market에서 자동차 헤드라이트 상 하향 빔 전환 시스템으로 주로 사용하고 있는 solenoid 방식의 여러 문제점을 개선하기 위하여 차량용 릴레이를 이용한 HID램프의 헤드라이트 상 하향 전환 컨트롤 방식를 제안하였다. 특히, 차종에 따라 달라지는 상 하향 빔 전환 입력신호에 대하여 릴레이가 일정하게 상 하향 동작을 할 수 있는 signal selector회로를 구성하고, 두 개의 램프를 relay로 전환하는 방식을 채택함으로서 그 동안 자동차 하우징 구조상 기존 H4 타입에만 국한되어 오던 차량용 HID램프의 헤드라이트 상 하향 빔 전환 시스템을 H1, H3, H7, H11, 9004, 9006, 9007 등 다른 베이스타입의 벌브에도 적용이 가능하도록 하여 우수한 범용성을 갖도록 하였다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.1
• /
• pp.156-160
• /
• 2012

Recently WCDMA signal transmission technology by large output microwave antenna have showed reduction of human resources and operating expense. But the existing antenna brackets cost is very expensive also its structure and functions are complicated. Unit brackets, suspending some sensors, subjected to acceleration loads, often fail due to self-vibration. To prevent such failures, it is necessary to understand the fatigue failure mode and to evaluate the fatigue life using tests or analysis techniques. The objective of this study is to develop the component test specifications, which are applicable to predict fatigue life at initial product design step, for unit brackets using vibration fatigue technique. So its application is limited to installation and management. In this project, we studied about more convenient bracket for microwave antennas through improvement on the existing antenna bracket's shortcoming and could develop an improved universal antenna bracket system for simple installation and application.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.84-87
• /
• 2008

In order to maximize the effect of installing screen door system while to minimize the problems in an initial stage of introduction, it is strongly required to research an optimum installation solution in connection with ventilation and disaster prevention system alongside with safety structure analysis of screen door in respect to train-induced wind, as well as to develop the criteria for the operation after the installation. This paper presents the results of study to develop the optimum design technology in urban railway equipped with platform screen door systems.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.397-403
• /
• 2004

The controller area network(CAN) was originally developed to support cheap and rather simple automative applications, However, because of the its performance and low cost, it is also being considered in automated manufacturing and process control environments to interconnect intelligent devices, such as modem sensors and actuators. This paper presents a new application technology of the developed CAN control modules for the automated doors in building automation system. Key pad and RF methods are used to open and close the automated door by the slave CAN module with CAN protocol. BAS application technology of CAN field bus modules is also presented firstly in our nation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.10
• /
• pp.72-80
• /
• 2012

In general, electronic conveyor scales are installed in a relatively distributed manner on the crushed rock and sand production site. It is one of the time-consuming and difficult engineering works to monitor and control the plant operation status such as the management of measuring data, malfunction of belt conveyor, and fault of electronic conveyor scale. Therefore, to alleviate the inefficient problems and to monitor the operating plant in the online and remote control room, a remote calibration and real-time monitoring system, which is practically applied to the electronic conveyor scale system and verified by onsite experiment, is developed based on the LabVIEW.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.05a
• /
• pp.164-167
• /
• 2009

It is difficult to measure junction temperature in the LED Module. According to the arrangement control unit and heat sink, temperature distribution is changed in the LED Module. A method of forecasting LED Module thermal resistance is suggested with measuring LED and PCB board temperature.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2008.11a
• /
• pp.189-194
• /
• 2008

Augmentation of the high-technology industry semiconductor factories, to acquire productivity and competitive power, is an international tendency. This situation is demanding for the functional counteractions. This study is regarding egress distance pertaining to installation of direct stairs. First, analyze situations and danger characteristics of LCD Factories. Second, through investigations and analysis of both domestic and foreign Egress Distance Code, propose rational Egress Distance Code pertaining to installation of direct stairs.

• Electronics and Telecommunications Trends
• /
• v.33 no.3
• /
• pp.41-50
• /
• 2018

In order to ensure the electromagnetic safety of a complex facility equipped with a variety of electric and electronic equipment, the European Union (EU) has enacted and applied the Electromagnetic Compatibility Directive (EMC Directive 2004/108/EC) to a fixed installation. This paper introduces the regulations and techniques related with electromagnetic compatibility (EMC) engineering applied to a fixed installation, which is used to prevent a malfunction of critical equipment and systems caused by unwanted electromagnetic waves and to operate the facilities with stability.