• Analytical Science and Technology
• /
• v.7 no.4
• /
• pp.517-526
• /
• 1994

Large insoluble phases and dispersoids in Al-Li-Cu-Mg-Mn-Zr alloys containing Mn were analyzed with EPMA(Electron Probe Microanalyzer) and SAEM(Scanning Auger Electron Microscope). Morphology, distribution and volume fraction of the large insoluble phase were also analyzed quantitatively by optical microscopy. Mechanical properties were tested at room temperature and at $200^{\circ}C$. With increasing Mn contents, the volume fraction of the large insoluble phases increased steeply, thus decreasing ductility. Mn was found to be very effective for obtaing uniformly distributed fine-grain structures. The alloy containing 0.44 wt% Mn showed the highest tensile strength among Mn-bearing alloys tested.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.12
• /
• pp.1187-1192
• /
• 2000

Ternary (Mo-Ru-Pd) and binary (Mo-Ru, Mo-Pd) alloys have been prepared using an Ar arc melting furnace. Mo and the noble metals, Ru and Pd, are the constituents of metallic insoluble residues, which were found in the early days of post-irradiation studies on uranium oxide fuels. In the present study, the structure of the alloys was evaluated using a powder X-ray diffractometer. Unit cell parameters were determined by least squares refinements of powder X-ray diffraction data. Scanning electron microscopic analyses of the surface of the alloys indicated that surface morphology was dependent on the crystallographic structure as well as its composition. Measurements of the magnetic susceptibility of the alloys showed evidence of superconducting transition from 3 to 9.2 K. Among the ternary and binary alloys, the ${\sigma}-phase$ showed the highest superconducting transition temperature,~9.2 K.

• Journal of Surface Science and Engineering
• /
• v.32 no.6
• /
• pp.686-694
• /
• 1999

Insoluble anodes of the Ta/Ir mixed metal oxide for electrodeposition of Ni-W alloy in ammoniacal citrate bath were prepared by thermal decomposition method. Ti plate was etched in boiling oxalic acid solution and coated with ethanol solution of $TaCl_{5}$ and $IrCl_4$ mixed in a fixed ratio, followed by drying and treating at various temperatures. The coating layer of these insoluble anode was characterized by SEM, EDX, XRD and DSC. The decomposition rate of citric acid in plating bath was determined by measuring the $CO_2$ gas evolved at the anodes with Gas Chromatography. Evolution of $CO_2$ gas from Ta/Ir oxide anodes decreased about 5% compared with that of Pt. The $CO_2$ gas evolution was increased with the amount of Ir-oxide in the coatings. The coatings which have more than 40% ratio of Ta content and heat-treated at the temperature higher than $400^{\circ}C$ showed better efficiency

• Analytical Science and Technology
• /
• v.11 no.6
• /
• pp.485-494
• /
• 1998

Ternary and quaternary alloys composed of Mo-Ru-Rh-Pd were prepared and their crystal structure and quantitative chemical compositions were analysed by XRD, WDX, EDX and ICP/AES. The results of X-ray diffraction studies showed that the alloys were crystallized in hexagonal close packing, well known as ${\varepsilon}$-phase with $P6_3/mmc$ of space group. The optimum accelerating voltage for Zr~Cd(40~48) analyzed by EPMA using PET crystal was found to be 15 kV and the linear regression coefficient(R) of atomic number and X-ray intensity was approximately 0.998 without Tc standard specimen. The WDX results of alloys of Mo and Pd by linear regression equations were detected to be 0.1% lower compared to WDX analysis results using standard specimen, while Ru, Rh were detected 3% higher. These alloys were completely dissolved in mixed acid of 12.5 mL HCl and 1 mL $HNO_3$, at $220^{\circ}C$ for 22 hours using autoclave with PTFE vessel. There was no reprecipitating phenomnon when diluted 100 times with 1N-HCl. The results of ICP/AES analysis deviated less than 4% comparing with those of normal WDX analysis.

• Analytical Science and Technology
• /
• v.11 no.3
• /
• pp.189-193
• /
• 1998

Binary alloys, $MoRu_3$ and $MoRh_3$, have been prepared using arc melting furnace. Mo and the noble metals Ru and Rh are the constituents of metallic insoluble residues, which were found in the early days of the post-irradiation studies on uranium oxide fuels. Detailed structural informations about these alloys have not been reported on JCPDS files of ICDD (International Centre for Diffraction Data). The results of X-ray diffraction study showed that the alloy was crystallized in hexagonal close-packing, well known as ${\varepsilon}$-phase. The X-ray diffraction patterns of these alloys matched well to that of $WRh_3$ with $P6_3/mmc$ of space group. The lattice parameters, a and c, were calculated using the least squares extrapolation. It was found from X-ray photoelectron spectroscopic measurements that Mo on the surface of the alloy was oxidized to Mo(6+), which could be removed by sputtering with Ar ions for approximately 15 minutes. The changes in binding energy of Mo, Ru, and Rh on the surface of the alloy were not observed. Magnetic susceptibility measurements resulted in the typical Pauli-paramagnetic behavior in the temperature range of 2 to 300 K.

• Journal of the Korean Magnetics Society
• /
• v.5 no.1
• /
• pp.8-14
• /
• 1995

The magnetic properties of an $Fe_{87}Zr_{7}B_{5}Ag_{1}$(at.%) amorphous alloy have been investigated as a function of annealing temperatures to clarify its application potential as a core material for high-frequency use by adding a small amount of insoluble element of Ag. A new excellent soft magnetic material was developed. The amorphous alloy produced by relatively low temperature annealing at $T_{a}=400^{\circ}C$ exhibited very high initial permeability$(\mu_{i})$ of 288,000 at 1kHz and 2mOe, very low coercivity$(H_{c})$ of 15mOe and low core loss$(W_{c})$ of 50W/kg at 100kHz and 1,000G which is comparable with Co-based amorphous alloys, respectively. It is notable that the values obtained in the present study are the best magnetic properties among various kinds of Fe-based soft amorphous materials reported up to date. The reasons for the achievement of good soft magnetic properties are presumably due to the homogeneous formation of very fine $\alpha$-Fe clusters with the size of 2~3nm in an amorphous matrix, which can be deduced from the increase of resistivity and the TEM observation. The very fine $\alpha$-Fe clusters embedded in an amorphous matrix had a great influence on reduction of magnetostriction and refinement of magnetic domain.