• 한국정보통신학회논문지
• /
• 제7권4호
• /
• pp.812-818
• /
• 2003

산업용 및 공조용 팬 동력원의 대부분이 농형 유도전동기를 사용하고 있으며 그 구조는 외측 고정자에 의해 내측 회전자가 회전하는 형태이다. 이와는 반대로 내측 고정자에 의해 외측 회전자가 구동되는 외측 회전형 방식의 유도전동기는 적은 전류로 지속적인 큰 토크가 필요한 펀 둥에 적합한 형태라고 할 수 있다. 즉, 외측이 회전함으로써 큰 관성력을 얻을 수 있으므로, 일단 회전하게 되면 큰 토크를 지속적으로 발생시킬 수 있다. 그리고, 일시적인 입력 전압의 변동이나 부하 변동시에도 외측 회전자의 큰 관성력에 힘입어 송풍량을 고르게 해주는 역할을 할 수 있으리라 사료된다. 본 논문에서는 팬 또는 이와 유사한 특성을 가진 부하의 동력원으로 사용할 목적으로, 외측 회전형 유도 전동기의 회전자를 설계, 제작하여 고정자 저항시험, 무부하시험 및 회전자 구속시험을 통해 등가회로 정수를 측정하였다. 그리고, 부하시험을 행하여 얻은 토크-속도, 출력, 역률 및 효율 특성곡선을 분석함으로써 외측회전형 유도전동기 개발과 관련된 기술적인 토대를 마련하고자 한다.

• 한국정밀공학회지
• /
• 제3권3호
• /
• pp.40-71
• /
• 1986

By developing a computer program for the systematic design of worm gears, the design formulae and tables of AGMA, JGMA, BS and DIN are analized and compared. The computer program can be used on micro-computers. According to the input data of the reduction ratio, the center distance. the driving torque and the material as design parameters, the program calculate the most efficient worm gear dimension. The variation of the design parameters and other empirical coefficients in case of resulting an inadequate design gear dimension can be easily modified throuth the way of interactive method between the user and the monitoring system of computer. A proposal of the standardization of worm gears was made in which a standard module according to the DIN 323 standard series number was applied. For the more exact and effective calculation of the stress concentration and the deformation of gear teeth, a computer program using the boundary element method is also developed. Even the strength of the special gear shape such as Niemann's "Cavex" gear can be calculated in a short CPU-time. The most effort of this study has been layed on the developing a computer program for the correction of a tooth profile and face width which is most important design factor for an exact and wide teeth contacts under loads, especially by great and wide gears. For this purpose were investigated the tooth stiffness, the mesh interferences and the kinematics and the dynamics of gear mesh. The deflection and the deformation of the gear shaft due to the loads acting on gear and shaft were aslo considered. Some examples have shown the sufficient good status of teeth contact in which the correction of the tooth profile and face width were accomplished due to the calculated results.d results.

• 한국가스학회지
• /
• 제24권3호
• /
• pp.47-53
• /
• 2020

본 연구에서는 엔진발전기에 사용되는 냉각팬 형상을 단방향 유동-구조 연성해석을 통하여 냉각팬의 성능과 내구성을 분석하여 최적화 설계자료를 제시하였다. 이를 위해, 냉각팬 내부 유동장에 대해 정상상태 해석을 수행하고, 정상상태 계산 결과를 구조해석을 위한 입력 데이터로 사용함으로써 내구성을 분석하였다. 냉각팬의 블레이드와 스윕 각도를 변경하는 작업을 통해 6가지 type을 모델링하여 유동해석을 진행하였으며, 질량유량과 토오크의 비는 A type이 가장 우수하지만, 질량유량이 상대적으로 큰 B type이 유동성능이 가장 좋은 냉각팬의 형상이라고 판단하였다. 유동해석을 통해 선정된 B type의 블레이드 두께를 4가지로 설정하여 구조해석을 검토한 결과, 피로안전계수까지 고려하였을 때 B Type-3가 가장 적합하다고 판단되었다.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.391-396
• /
• 2009

In this paper, a control algorithm for DC-Link voltage unbalancing compensation of a four-switch inverter for a three-phase BLDC motor drive is proposed. Compared with a conventional six-switch inverter, the split source of the four-switch inverter can be obtained by splitting DC-link capacitor into two capacitors to drive the three phase BLDC motor. The voltages across each of two capacitors are not always equal in steady state because of the unbalance in the impedance of the DC-link capacitors $C_1$ and $C_2$ or the variable current flowed into the capacitor's neutral point in motor control. Despite the unbalance, if the BLDC motor may be run for a long time the voltage across one of the capacitors is more increased. So the unbalance in the capacitors voltages will be accelerated. As a result, The current ripple and torque ripple is increased due to the fluctuation of input current which flows into 3-phase BLDC motor. According to that, the vibration of motor will be increased and the whole system will be instable. This paper presents a control algorithm for DC-Link voltage unbalancing compensation. The sampling from the voltages across each of two capacitors is used to perform the voltage control of DC-Link by using the feedforward controller.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.1-11
• /
• 2011

The skid-steering method that applied a number of mobile robot currently is extremely effective in narrow area. But it contains several problems such as its natural properties, slip, occurred by different direction between vehicle's driving and wheel's rotary. Through this paper, suitable control algorithm of $6{\times}6$ skid steering wheeled vehicle and its driving methods are proposed by analyzing the behavior $6{\times}6$ skid-steered wheeled vehicle model designed by engineering analysis strategy. To do this, based on a behavior of designed driving system, required torque and other performance of in-wheel type motor system are considered, and finally control algorithm for each wheel is proposed and simulated using this model. To test the proposed vehicle system, driver model is designed using PID closed loop system and included in the total driving control algorithm. The Performance of designed vehicle model is verified by using DYC (Direct Yaw Control) cornering mode and slip mode control to follow the steering input which are essential to evaluate the driving performance of $6{\times}6$ vehicle. Proposed modeling strategy and control method will be implemented to the real $6{\times}6$ in-wheel drive type vehicle.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.47-55
• /
• 2008

Turbocharger has a main purpose on recycling of the exhaust gas from the engine cylinder. On the basis of the facility characteristics, the turbocharger supported on floating ring bearings has some problems such as the large volume, oil supplement for lubrication and high power loss due to high operating torque. The air foil bearing has been studied as the bearing element to be able to alternate the floating ring bearing without the problems of the floating ring bearing. In this study, the air foil bearing has 2 parts; journal and thrust bearings, and the test facility consists of the engine, exhaust and intake parts. In addiction, the specification of the turbocharger follows a small turbocharger for SUV engine. The engine speed is varied from 750 (idle rpm) to 2,500 rpm and then, the rotating speed of the turbocharger rotor is accelerated from 0 to 100,000 rpm. From those experiments, the comparison between the performances of the air foil bearing and floating ring bearing is conducted and the results show that the air foil bearing has less power loss, maximum 770 watt, than the floating ring bearing, maximum 5,110 watt. This result verifies that the air foil bearing is more efficient and able to output more power under the same condition of the input power.

• 전력전자학회논문지
• /
• 제3권3호
• /
• pp.214-221
• /
• 1998

직접 구동용 브러시 없는 직류전동기(BRUSHLESS direct drive motor : BLDD motor)의 강인한 위치제어를 위해 신경망을 사용하여 접근하는 새로운 제어방식이 소개된다. 전향 신경망이 추가된 선형 2차 제어기는 AC서보의 객체지향 방법을 사용함으로서 대략적으로 선형화 되어지는 강인한 BLDD 모터 시스템을 얻기 위해 사용된다. 구동 상태의 온-라인 위상에서 학습되는 이 신경망은 전향신호와 오차 역 전파법(Back-Propagation Method)에 의해 구성된다. 총 노드의 수가 8개이기 때문에 이 시스템은 일반적인 마이크로 프로세서에 의해 쉽게 실현될 수 있다. 일반적인 작동중, 입출력 응답은 표본화되어지고 가중치는 매개변수 또는 부하 토크의 능한 변이를 적용하기 위해 각 표본주기에서 오차 역 전파법에 의해 학습된다. 그리고, 상태공간에서 시스템 분석은 상태 궤환 이득을 얻기 위해 체계적으로 실행했다. 또한, 강인성은 전반적인 시스템응답에 영향력을 주지 않고 얻어진다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1445-1449
• /
• 2005

The ram assembly is important equipment in fueling machine of PHWR(Pressurized Heavy Water Reactor) plant where fuel replacement is possible while the plant is in service. Troubles in the ram assembly can cause lots of difficulties in power plant operation. The ram assembly is typically composed of the B-ram, the L-Ram and the C-Ram. The B-ram is focused in this paper because it plays the most important role in the ram assembly. Among the ram fault phenomena, ram stuck phenomena are the most frequent cases in the B-ram, which has a ball screw mechanism driven by a hydraulic motor. Ram stuck phenomena are due to ball wear and damage in ball nut that increase in proportion to the number of fuel replacement. It is required to predict ram stuck phenomena before they occur. In this paper, a method is proposed for predicting ram stuck phenomena using a discrete wavelet transform. The discrete wavelet transform provides information on both the time and frequency characteristics of the input signals. The proposed method uses the frequency bandwidths of coefficients of discrete wavelet decompositions and detail coefficients of discrete wavelet transform to predict ram stuck phenomena. The signal used in this paper is a torque-related signal such as a hydraulic service outlet pressure signal in a hydraulic driving system or a current signal in a DC motor driving system. Finally, the validity of the proposed method is shown via experiment using ball nut characteristic test equipment that simulates ram stuck phenomena due to increased ball friction in ball nut.

• 농업과학연구
• /
• 제42권1호
• /
• pp.53-61
• /
• 2015

Development of highly efficient and energy-saving tractors has been one of the issues in agricultural machinery. For design of such tractors, measurement and analysis of load on major power transmission parts of the tractors are the most important pre-requisite tasks. Objective of this study was to perform pre-processing procedures before effective analysis of load data of agricultural tractors (30, 75, and 82 kW) during major field operations such as plow tillage, rotary tillage, baling, bale wrapping, and to select the suitable pre-processing method for the analysis. A load measurement systems, equipped in the tractors, were consisted of strain-gauge, encoder, hydraulic pressure, and radar speed sensors to measure torque and rotational speed levels of transmission input shaft, PTO shaft, and driving axle shafts, pressure of the hydraulic inlet line, and travel speed, respectively. The entire sensor data were collected at a 200-Hz rate. Plow tillage, rotary tillage, baling, wrapping, and loader operations were selected as major field operations of agricultural tractors. Same or different farm works and driving levels were set differently for each of the load measuring experiment. Before load data analysis, pre-processing procedures such as outlier removal, low-pass filtering, and data division were performed. Data beyond the scope of the measuring range of the sensors and the operating range of the power transmission parts were removed. Considering engine and PTO rotational speeds, frequency components greater than 90, 60, and 60 Hz cut off frequencies were low-pass filtered for plow tillage, rotary tillage, and baler operations, respectively. Measured load data were divided into five parts: driving, working, implement up, implement down, and turning. Results of the study would provide useful information for load characteristics of tractors on major field operations.

• 전력전자학회논문지
• /
• 제6권2호
• /
• pp.132-140
• /
• 2001

유니버셜모터는 소형의 직류 직권전동기와 같은 기계적 구조를 가지며 교류.직류 전원을 양용할 수 있는 장점으로 동급의 일반전동기에 비해 높은 속도로 구동이 가능하므로 핸드드릴이나 진공청소기, 세탁기 등의 가정용 기기 등에 일반적으로 사용된다. 위상각제어기를 이용하여 모터로 입력되는 전압을 제어하는 방법은 간단한 구조 때문에 위상지연으로 인해 입력 역률 및 저차 고조파 전류특성이 좋지 않음에도 불구하고 널리 사용되고 있다. 브리지 정류기를 사용하여 교류 전원을 맥동하는 직류 전원으로 변환한 후 DC 초퍼로써 유니버셜모터에 입력되는 평균전압을 제어하는 방법은 제어기의 효율을 높일 수 있고 저차 고조파전류를 감소시킬 뿐만 아니라 저전력값에 대해서도 부하역률의 저하를 막을 수 있다. 본 논문에서는 기존의 제어기의 방법으로 저가의 위상각 제어기를 구서하고 EH한 저가의 마이크로 컨트롤러를 이용한 DC 초퍼시스템을 각각 구성하여 저차 고조파전류 특성을 비교 분석하였다.