• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 추계학술대회 논문집 학회본부
• /
• pp.168-171
• /
• 1988

The p-n homo junction diode of the III-V ternary alloy semiconductor $In_{1-x}Ga_xP$ : S grown by the temperature gradient solution (TGS) was fabricated by Zn-diffusion, and it's characteristics was investigated. The carrier concentration of $In_{1-x}Ga_xP$ doped with sulfur, 0.5 mol %, was $1{\times}10^{17}cm^{-3}$ and the mobility was varied with the composition. In the case that the diffusion time was constant as 30 minutes. The temperature dependence of diffusion coefficient was decreased from D= $4.2{\times}10^{-5}$ exp (-1.74/$k_{B}T$) to D= $2.5{\times}10^{-5}$ exp (-3.272/$k_{B}T$) with increasing of composition $\times$ from 0.43 to 0.98. The major peak of E.L spectrum was due to D-A pair recombination and the peak intensity was increased with the increasing of input current. And the E.L intensity was decreased with the increasing temperature, and shift to the long wavelength. The luminescence efficiencies measured at $5^{\circ}C$, atmosphere temperature, was decreased from $2.6{\times}10^{-4}$% to $9.49{\times}10^{-6}$ % with increasing of composition it from 0.39, direct transition region, to 0.98, indirect transition region.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.236-238
• /
• 1997

A cellular power amplifier using an APCVD(Atmospheric Pressure Chemical Vapor Deposition)-grown SiGe base HBT of ETRI has been designed with a linear simulation CAD. The Si/SiGe HBT with an emitter area of 2$\times$8${\mu}{\textrm}{m}$$^2$typically has a cutoff frequency(f$_{T}$) of 7.0 GHz and a maximum oscillation frequency(f$_{max}$) of 16.1 GHz with a pad de-embedding A packaged power Si/SiGe HBT with an emitter area of 2$\times$8$\times$80${\mu}{\textrm}{m}$$^2$typically shows a f$_{T}$ of 4.7 GHz and a f$_{max}$ of 7.1 GHz at a collector current (Ic) of 115 mA. The power amplifier exhibits a Forward transmission coefficient(S21) of 13.5 dB, an input and an output reflection coefficients of -42 dB and -45 dB respectively. Up to now the III-V compound semiconductor devices hale dominated microwave applications, however a rapid progress in Si-based technology make the advent of the Si/SiGe HBT which is promising in low to even higher microwave range because of lower cost and relatively higher reproducibility of a Si-based process.ess.ess.

• 한국전기전자재료학회논문지
• /
• 제19권2호
• /
• pp.162-168
• /
• 2006

Recently, diagnosis techniques have been investigated to detect a Partial Discharge associated with a dielectric material defect in a high voltage electrical apparatus, However, the properties of detection technique of Partial Discharge aren't completely understood because the physical process of Partial Discharge. Therefore, this paper analyzes the process on surface discharge of polymer insulator using wavelet transform. Wavelet transform provides a direct quantitative measure of spectral content in the time~frequency domain. As it is important to develop a non-contact method for detecting the kaolin contamination degree, this research analyzes the electromagnetic waves emitted from Partial Discharge using wavelet transform. This result experimentally shows the process of Partial Discharge as a two-dimensional distribution in the time-frequency domain. Feature extraction parameter namely, maximum and average of wavelet coefficients values, wavelet coefficients value at the point of $95\%$ in a histogram and number of maximum wavelet coefficient have used electromagnetic wave signals as input signals in the preprocessing process of neural networks in order to identify kaolin contamination rates. As result, root sum square error was produced by the test with a learning of neural networks obtained 0.00828.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 D
• /
• pp.1803-1804
• /
• 2006

The purpose of this paper is to implement a Labview based TFDR Real Time system through the instruments of Pci eXtensions for Instrumentation(PXI). The proposed load impedance measurement algorithm was verified by experiments via the implemented real time system. The TFDR real time system consisted of the reference signal design, signal generation, signal acquisition, algorithm execution and results display parts. To implement real time system, all of the parts wore programmed by the Labview which is one of graphical programming languages. In the application software implemented by the Labview we were able to design a suitable reference signal according to the length and frequency attenuation characteristics of the target cable and controled the arbitrary waveform generator(ZT500PXI) of the signal generation part and the digital storage oscilloscope(ZT430PXI) of the signal acquisition part. By using the TFDR real time system with the terminal resistor on the target cable, we applied to the load impedance measurements. In the proposed load impedance algorithm a normalized time-frequency cross correlation function and a cross time-frequency distribution function was employed to calculate the reflection coefficient and phase difference between the input and the reflected signals.

• 항공우주시스템공학회지
• /
• 제7권3호
• /
• pp.15-19
• /
• 2013

Tail wing is important to designing of civil aircrafts, because it is responsible for aircraft stability and control. Tail wing has a role in aircraft control and makes aircraft fly stably without any pilot control input. Also, designing of tail wing determine trim drag force in whole aircraft. Center of gravity(CG) of aircraft travels with various effects as placement of passenger's seats, location of cargo bay, etc. In designing horizontal tail volume, aircraft CG travel has to be considered to have margin so that it should be sized to provide adequate stability and control for the airplane's entire CG range throughout the flight envelope. Finally, it is essential to have sufficient elevator control to perform stall at forward CG for all flaps down configurations. Such stalls establish the FAR stall speed which airplane take-off and landing performance. This paper deals with the process for tail wing design regarding the aircraft CG travel and results for 95-seat type turboprop aircraft.

• 대한조선학회지
• /
• 제24권3호
• /
• pp.25-34
• /
• 1987

Whereas the finite element method is well established today, the boundary element method is a fairly recent development. Both are general-purpose methods for the solution of various structural analysis problem. The B.E.M has several potential advantages relative to the F.E.M. One of them is that the number of unknowns in algebraic system obtained by discretization is proportional to the number of boundary nodes. Anothor advantage is the ease of discretization and input data preparation. However, the B.E.M. always leads to a fully populated and unsymmetric system of equations. Even though the number of degree-of-freedom is reduced as compared with F.E.M, since nodes exist on the boundary only in the B.E.M, to follow that the effort to solve the equations can be greater. It has been shown also that the time spent in setting up the coefficient matrix is a significant and can, in some cases, be greater than the time required to solve the equation. Thus, one can naturally consider the idea that two methods should be coupled, then the advantages of both methods can be taken. And further, by using this coupling method the HATCH CORNER was analyzed to give initial design data.

• 한국음향학회지
• /
• 제10권4호
• /
• pp.5-11
• /
• 1991

본 연구에서는 음성신호의 음소 단위 구분화 방법을 제안한다. 제안된 구분화 시스템은 화자 독립적이고, 음성신호에 대한 사전 정보 없이도 음소 단위로 구분화를 수행할 수 있는 특징을 갖는다. 구분화 처리는 입력 음성신호를 먼저 순수 유성을 구간과 순수 유성음이 아닌 구간으로 분리 시킨 후, 각각의 구간에 대해 세분화된 음소 단위로 분리시키는 2단계 구분화 알고리즘을 적용하였고, 이때 사용된 파라미터는 유성을 검출 파라미터, 영차 LPC 캡스트럼 계수의 시간변호 파라미터, ZCR 파라미터이다. 본 연구에서 제안한 구분화 알고리즘의 유용성을 입증하기 위해 사용한 대상어는 고립단어와 연속음성으로 구성된 어휘로서 전체 어휘중에 포함된 507개 음소에 대한 구분화율은 91.7% 이다.

• 전자공학회논문지C
• /
• 제36C권2호
• /
• pp.46-53
• /
• 1999

본 논문에서는 HDTV 비디오 신호를 처리함에 있어 신호의 병목현상을 없애주고 신호의 원활한 처리를 위해 새로운 알고리듬을 적용하여 54MHz의 동작 주파수를 갖는 패커를 제안하였다. 또한 제안된 패커의 성능을 검증하기 위해 조합논리를 이용한 ROM 테이블 구조를 갖는 DCT 계수 부호화부를 함께 설계하므로써 DCT 계수 부호화부의 출력을 제안된 패커의 입력 데이타로 사용하였다. 본 논문에서 제안된 회로는 VHDL 코드를 이용하여 설계하였고 SYNOPSYS tool의 $0.65{\mu}m$ 공정을 이용한 모델링과 시뮬레이션을 수행하였다.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2001년도 총회 및 춘계학술발표회
• /
• pp.3-6
• /
• 2001

Various Parameters such as stream velocities, discharges, and dispersion coefficients of dissolved solutes were estimated by fitting 1-D nonreactive solute transport model to the time-series chemistry data. This study was done for the reaches of Mankyung River lower than the Jeonju Wastewater Treatment Plant (Jeonju WTP). Korea. Concentrations of inorganic chemicals in the stream waters are strongly influenced by mixing with the chemically distinct effluent from Jeonju WTP. Sulfate, EC. and the total major cation were proved to be nearly conservative in the study area front their relationships with chloride, the conservative chemical species. The solute transport model was constrained to the time-series concentrations for these 4 conservative species. The variations of concentration and discharge of Jeonju WTP were used as input parameters, and the stream velocities, dispersion coefficients, and concentrations and discharges of some inflows were optimized. The differences between the observed arid simulated values for alkalinities and nitrates are inversely correlated and show diurnal fluctuations, indicating the photosynthesis. The parameters obtained front this mode] range from 550 to 774 kcmd (stream discharge at the outlet of the study area), from 0.06 to 0.10 m/sec (flow velocity), and from 0.7 to 6.4 m$^2$/sec (dispersion coefficient). The history of Jeonju WTP discharge was well predicted when optimized, indicating the validity of the model results.

• 한국연초학회지
• /
• 제22권2호
• /
• pp.151-156
• /
• 2000

The variability of a ventilated filter cigarette depends on the details of its construction and on the variabilities of its components. Variations in filter ventilation arise from many sources, including variations in tobacco rod pressure drop, filter tip pressure drop, tipping paper permeability, and plugwrap permeability. To reduce the filter ventilation variability, the variability of filter ventilation levels in ventilated cigarettes is studied by Monte Carlo Analysis. For each trials a value is selected for tobacco rod pressure drop, filter tip pressure drop, tipping paper permeability, and plugwrap permeability. These values are selected randomly from a normal distribution based on the target and coefficient of variation for each input variable. The results of this analysis for filter ventilation variation suggest that the variations of filter ventilation are dependent on the details of cigarette designs studied and reducing the variability of any cigarette component will reduce filter ventilation variability. For typical cigarettes, variation in the permeability of tipping paper is usually the most significant contributor to filter ventilation variability. Results of a Monte Carlo Analysis could provide both general insights and specific practical guidance about the design of ventilated filter cigarettes.