• Journal of the Semiconductor & Display Technology
• /
• v.20 no.3
• /
• pp.51-56
• /
• 2021

Using an inkjet printing process, we have investigated a droplet formation of poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) near the orifice of a piezoelectric inkjet head. With an attempt to form the smallest droplet without any satellites, we have applied various waveforms such as the unipolar, bipolar, and M-shaped waveforms. It is found that the droplet velocity and volume vary depending sensitively on the waveform width and voltage. Of those, the M-shaped waveform is shown to provide the smallest droplet volume, followed by the bipolar and then unipolar waveforms. The droplet printed on a PET film roll by the M-shaped waveform has the diameter as small as 46.1 ㎛. It is likely that the second short unipolar in the M-shape waveform increases the droplet velocity gradient, rendering the droplet smaller.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.105-105
• /
• 2006

IT 산업 및 반도체 산업이 발전함에 따라 초소형, 고집적화 시스템의 요구에 대응하기 위해서 고해상도 및 고정밀의 패턴 구현에 관한 많은 연구가 진행되고 있다. 이러한 연구는 각종 산업제품의 PCB(Printed Circuit Board) 및 디스플레이 장치인 PDP(Plasma Display Panel), LCD(Liquid Crystal Display) 등에 적용되어 널리 응용되고 있다. 현재 널리 사용되는 인쇄 회로 기판은 마스킹 후 선택적 에칭 방식을 적용하여 금속 배선을 형성하는 방식을 적용하고 있다. 이러한 방식은 설계가 변경될 경우 마스크를 다시 제작해야 하는 번거로움이 있어 설계 변경이 용이하지 않고 더욱 길어진 생산시간의 증가로 인하여 생산성 및 집적도가 떨어지게 된다. 따라서 최근에는 이러한 한계를 극복하기 위한 방안이 여러 가지 측면에서 시도되고 있으며, 그 중에서도 Inkjet Printing 기술에 대한 관심이 증가하고 있다. 본 연구에서는 Inkjet Printing 방식을 적용하여 금속 배선을 형성하고 선폭과 두께의 오차를 줄여 배선의 Tolerance 를 개선할 수 있는 방안을 제안하였다. Inkjet Printing 방식을 이용한 기존의 금속 배선 형성은 고해상도의 DPI(Dot Per Inch)에서 잉크 액적이 뭉치는 Bulge 현상이 발생되어 원하는 형상 및 배선의 폭을 구현하는데 어려움이 있었다. Bulge 현상은 배선의 불균일성을 야기할 뿐만 아니라 근접한 배선의 간섭에도 영향을 미처 금속 배선의 기능을 할 수 없는 단점을 발생시킨다. 따라서 본 연구에서는 이러한 Bulge 현상을 줄이고 배선간의 간섭을 방지하여 원하는 배선을 용이하게 형성할 수 있는 순차적 인쇄 방식을 적용하였다. 본 연구에서는 노즐직경 35um 의 Inkjet Head 와 나노 Ag 입자 잉크를 사용하여 Glass 표면 위에 배선을 형성하고 배선의 폭과 두께를 측정하였다. 또한 순차적 인쇄 방식을 적용하여 700DPI 이상의 고해상도에서 나타날 수 있는 Bulge 현상이 감소하였음을 관찰하였으며 금속 배선의 Tolerance를 10%내외로 유지할 수 있음을 확인하였다.

• Journal of Sensor Science and Technology
• /
• v.33 no.1
• /
• pp.24-29
• /
• 2024

Inkjet printing technology is used to mass-produce displays and electrochemical sensors by dropping tens of pico-liters or less of specific-purpose ink through nozzles, just as ink is sprayed and printed on paper. Unlike the deposition method for vaporizing material in a vacuum, inkjet printing technology can be used for processing even under general atmospheric pressure and has a cost advantage because the material is dissolved in a solvent and used in the form of ink. In addition, because it can only be printed on the desired part, masks are not required. However, a technical shortcoming is the difficulty for commercialization, such as uniformity for forming the thickness and coffee ring effect. As sizes of devices decrease, the need to print electrodes with precision, thinness, and uniformity increases. In this study, we improved the printing and processing conditions to form a homogeneous electrode using Ag ink (DGP-45LT-15C) and applied this for patterning to fabricate a heat sensor. Upon the application of voltage to the heat sensor, the model with an extended width exhibited superior heat performance. However, in terms of sheet resistance, the model yielded an equivalent value of 21.6 Ω/□ compared to the ITO.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1219-1225
• /
• 2003

According to the increase of lifetime and efficiency, the interest in the pLED has dramatically increased recently because pLED can be applied to large-size and flexible displays. The core process in the manufacture of pLED is the printing process of red, green and blue light emitting polymers (LEP), and inkjet printing method is one of the promising technology to print red, green and blue LEP on glass substrates. In this work, we developed a multi-head inkjet patterning system with 3 heads for each color. The developed inkjet patterning system is composed of the precise positioning system, head controller circuit, real-time ink drop evaluation system, maintenance system, and stable ink supply system. Finally, we investigated the stability and reliability of the system by printing red, green and blue LEP on the dummy substrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.610-615
• /
• 2022

BaTiO₃ is one of the ferroelectric materials with excellent dielectric properties such as high dielectric constant, low dielectric loss, and is widely used for the manufacturing of capacitors, piezoelectric converters, microsensors, and ferroelectric memories. Inkjet printing is a technology which uses digital and contactless methods which significantly improves flexibility associated with material and structural design, reducing manufacturing costs. Therefore, the top and bottom electrodes, BaTiO₃ ink, and photocurable resin were all printed by an inkjet to produce a BaTiO₃ capacitor. The properties of the printed thin film were analyzed. It was confirmed that the photocurable resin ink was well-infiltrated between the BaTiO₃ powder particles printed by inkjet. The dielectric properties of the capacitor such as dielectric constant which varies in accordance with frequency, polarization and tunability that changes with voltage, were measured.

• Journal of Information Display
• /
• v.10 no.3
• /
• pp.131-136
• /
• 2009

This is a report on the fabrication of a flexible OTFT backplane for electrophoretic display (EPD) using a printing technology. A practical printing technology for a polycarbonate substrate was developed by combining the conventional screen and inkjet printing technologies with the wet etching and oxygen plasma processes. For the gate electrode, the screen printing technology with Ag ink was developed to define the minimum line width of ${\sim}5{\mu}m$ and the thickness of ${\sim}70nm$ with the resistivity of ${\sim}10^{-6}{\Omega}{\cdot}cm$, which are suitable for displays with SVGA resolution. For the source and drain (S/D) electrodes, PEDOT:PSS, whose conductivity was drastically enhanced to 450 S/cm by adding 10 wt% glycerol, was adopted. In addition, the modified PEDOT:PSS could be neatly confined in the specific S/D electrode area that had been pretreated with oxygen. The OTFTs that made use of the developed printing technology produced a mobility of ${\sim}0.13cm^2/Vs.ec$ and an on/off current ratio of ${\sim}10^6$, which are comparable to those using thermally evaporated Au for the S/D electrode.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.2
• /
• pp.73-81
• /
• 2011

We manufactured the inkjet printing system for the application into the nano Ag finger line interconnection process in Si solar cells. The home-made inkjet printer consists of motion part for XY motion stage with optical table, head part, power and control part in the rack box with pump, and ink supply part for the connection of pump-tube-sub ink tanknozzle. The ink jet printing system has been used to conduct the interconnection process of finger lines on Si solar cell. The nano ink includes the 50 nm-diameter. Ag nano particles and the viscosity is 14.4 cP at $22^{\circ}C$. After processing of inkjet printing on the finger lines of Si solar cell, the nano particles were measured by scanning electron microscope. After the heat treatment at $850^{\circ}C$, the finger lines showed the smooth surface morphology without micropores.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1806-1809
• /
• 2008

Study that form micro pattern by direct ink jet printing method is getting attention recently. Direct ink jet printing spout fine droplet including nano metal particle by force or air pressure. There is reason which ink jet printing method is profitable especially in a various micro-patterning technology. It can embody patterns directly without complex process such as mask manufacture or screen-printing for existent lithography. In this study, research of a technology that ejects fine droplet form of Pico liter and forms metal micro pattern was carried with inkjet head of piezoelectricity drive system. Droplet established pattern while ejecting consecutively and move on the surface at the fixed speed. Patterns formed in ink are mixed with organic solvent and polymer that act as binder. So added thermal hardening process after evaporate organic solvent at isothermal after printing. I executed high frequency special quality estimation of CPW transmission line to confirm electrical property of manufactured circuit board. We tried a large area printing to confirm application possibility of an ink jet technology.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.2
• /
• pp.464-468
• /
• 2012

Three solvent systems, chlorobenzene (ink 1), chlorobenzene/o-dichlorobenzene (ink 2) and chlorobenzene/tetrahydronaphthalene (ink 3), were compared as printable inks for the fabrication of polymer light-emitting diodes (PLEDs) using poly[2-methoxy-5-(2-ethylhexyl-oxyl)-1,4-phenylenevinylene (MEH-PPV) as an emissive material and an inkjet printer (Fujifilm Dimatix DMP-2831). Ink 1 clogged the printer's nozzle and gave non-uniform film. Inks 2 and 3 were used to fabricate PLEDs with ITO/PEDOT:PSS/MEH-PPV/LiF/Al configurations. The best performance (turn-on voltage, 3.5 V; luminance efficiency, 0.17 cd/A; luminance, 1,800 cd/m) was obtained when ink 3 was used to form the emissive layer (thickness, 49 nm), attributable to the better morphology and suitable thickness of the MEH-PPV layer.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.6
• /
• pp.271-274
• /
• 2011

Screen-printed source and drain electrodes were used for a spin-coated and inkjet-processed zinc-tin oxide (ZTO) TFTs for the first time. Source and drain were silver nanoparticles. Channel length was patterned using screen printing technology. Different silver nanoinks and process parameters were tested to find optimal source and drain contacts Relatively good electrical properties of a screen-printed inkjet-processed oxide TFT were obtained as follows; a mobility of 1.20 $cm^2$/Vs, an on-off current ratio of $10^6$, a Vth of 5.4 V and a subthreshold swing of 1.5 V/dec.