• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.108-108
• /
• 2007

Inkjet printing is a non-contact and direct writing associated with a computer. In the industrial field, there have been many efforts to utilize the inkjet printing as a new way of manufacturing, especially for electronic devices. The etching resist used in this process is an organic polymer which becomes solidified when exposed to ultraviolet lights and has high viscosity of 300 cPs at ambient temperature. A piezoelectric-driven ink jet printhead is used to dispense $20-40\;{\mu}m$ diameter droplets onto the copper substrate to prevent subsequent etching. In this study, factors affecting the pattern formation such as printing resolution, jetting property, adhesion strength, etching and strip mechanism, UV pinning energy have been investigated. As a result, microscale Etch resist patterning of printed circuit board with tens of ${\mu}m$ high have been fabricated.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1542-1543
• /
• 2007

This paper presents the effect of driving waveform for piezoelectric bend mode inkjet printhead with optimized mechanical design. Experimental and theoretical studies on the applied driving waveform versus jetting characteristics were performed. The inkjet head has been designed to maximize the droplet velocity, minimize voltage response of the actuator and optimize the firing frequency to eject ink droplet. The head design was carried out by using mechanical simulation. The printhead has been fabricated with Si(100) and SOI wafers by MEMS process and silicon direct bonding method. To investigate how performance of the piezoelectric ceramic actuator influences on droplet diameter and droplet velocity, the method of stroboscopy was used. Using the water based ink of viscosity of 11.8 cps and surface tension of 0.025N/m, it is possible to eject stable droplets through 64 nozzles average velocity of 4.05 m/s with standard deviation of 0.06 m/s and average diameter of $29.2\;{\mu}m$ with standard variation of $0.5\;{\mu}m$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.11 s.254
• /
• pp.1107-1116
• /
• 2006

The droplet ejection process driven by an evaporating bubble in a thermal inkjet printhead is investigated by numerically solving the conservation equations for mass, momentum and energy. The phase interfaces are tracked by a level set method which is modified to include the effect of phase change at the interface and extended for multiphase flows with irregular solid boundaries. The compressibility effect of a bubble is also included in the analysis to appropriately describe the bubble expansion behaviour associated with the high pressure caused by bubble nucleation. The whole process of bubble growth and collapse as well as droplet ejection during thermal inkjet printing is simulated without employing a simplified semi-empirical bubble growth model. Based on the numerical results, the jet breaking and droplet formation behaviour is observed to depend strongly on the bubble growth and collapse pattern. Also, the effects of liquid viscosity, surface tension and nozzle geometry are quantified from the calculated bubble growth rate and ink droplet ejection distance.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.134-134
• /
• 2009

원자층 증착법을 이용하여 platinum group metal(Ru, Ir, Pt). metal nitride(TaN, TiN, AlN), 그리고 metal oxide($Al_2O_3$, $TiO_2$)을 증착하고, 미세구조와 공정 변수가 내산화성, 내부식성, 저항 및 온도저항계수에 미치는 영향을 연구하였다. proto-type의 전자저항막 제조를 통해 종래의 TaN 전자저항막에 비해 우수한 내부식성 및 내산화성을 가짐을 확인하였다.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1892-1897
• /
• 2003

A new thermal inkjet printer head on SOI wafer with virtual valve was proposed. It was composed of two rectangular heaters with same size. So we could call it T-jet(Twin jet). T-jet has a lot of merits. It has the advantage of being fabricated with one wafer and is easy to change the size of chamber, nozzle, restrictor and so on. However, above all, It is the best point that T-jet has a virtual valve. And it was manufactured on SOI wafer. The chamber was formed in its upper silicon whose thickness was 40um. The chamber's bottom layer was silicon dioxide of SOI wafer and two heaters were located underneath the chamber's ceiling. And the restirctor was made beside the chamber. Nozzle was molded by process of Ni plating. Ni was 30um thick. Nozzle ejection test was performed by printer head having 56 nozzles in 2 columns with 600NPI(nozzle per inch) and black ink. It measured a drop velocity of 12m/s, a drop volume of 30pl, and a maximum firing frequency of 12KHz for single nozzle ejection. Throwing out the ink drop in whole nozzles at the same time, it was observed that the uniformity of the drop velocity and volume was less than 4%.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.8
• /
• pp.45-50
• /
• 2008

An ink jetting measurement system has been developed such that the velocity as well as the volume of ink droplets can be measured. In order to measure the ink droplet, a strobe LED light was synchronized to the droplet firing signal in order to obtain frozen droplet images. Then, a LabVIEW based software was developed for the analysis of the droplet image. For the efficient droplet analysis, a user generated rectangular shaped ROI (Region of Interest) was used. By using ROI, the ink droplet image can be easily isolated from the other structures such as printhead and the processing area can be minimized.

• Journal of computational fluids engineering
• /
• v.17 no.2
• /
• pp.65-70
• /
• 2012

The droplet ejection behavior from drop-on-demand printhead are investigated numerically in terms of the non-dimensional parameters. The numerical simulation is performed using a volume-of-fluid model. It is important to eject droplet within the printability range, where the droplet is ejected in stable manner without satellite droplets. Generally, the printability range has been determined by Z number, which is the inverse of Oh number. However, it is found that the ejection of droplets with same Z number can exhibit different behavior depending on the value of Ca and We number. Therefore, it is insufficient to determine the printability range only with Z number. Instead, other non-dimensional parameters, such as Ca and We number, should be considered comprehensively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.4 s.235
• /
• pp.526-533
• /
• 2005

Reliability problem in inkjet printhead, one of MEMS devices, is also very important. To eject an ink drop, the temperature of heater must be high so that ink contacting with surface reaches above $280^{o}C$ on the instant. Its heater is embedded in the thin multi-layer in which several materials are deposited. MEMS processes are the main sources of residual stresses development. Residual stress is one of the factors reducing the reliability of MEMS devices. We measured residual stresses of single layers that consist of multilayer. FE analysis is performed using design of experiment(DOE). Transient analysis for heat transfer is performed to get a temperature distribution. And then static analysis is performed with the temperature distribution obtained by heat transfer analysis and the measured residual stresses to get a stress distribution in the structure. Although the residual stress is bigger than thermal stress, thermal stress is more influential on fatigue life.

• Journal of computational fluids engineering
• /
• v.17 no.3
• /
• pp.33-38
• /
• 2012

The droplet ejection behavior from drop-on-demand printhead are investigated numerically for Newtonian and shear-thinning fluid. The numerical simulation is performed using a volume-of-fluid model. In this study, we compare the printable range in terms of Z number and pinch-off time for Newtonian and shear-thinning fluids. The printability range are found to be 1.08 $$\leq_-$$ Z $$\leq_-$$ 12.9 for Newtonian fluid and 0.8 $$\leq_-$$ Z $$\leq_-$$ 12.9 for shear-thinning fluid. However, air entrainment is observed during merging of primary and satellite droplet within the printability range. The pinch-off time of the shear-thinning fluid is apparently shorter compared to the corresponding Newtonian fluid due to shear-thinning effects and the differences in the pinch-off time is enlarged significantly when the capillary number is larger than 0.5.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.504-504
• /
• 2011

최근 디지털 프린팅 기술의 핵심기술로 떠오르고 있는 잉크젯 프린팅 기술은 최근 기존의 문서인쇄 뿐 아니라, 직물 인쇄, 태양전지 등의 다양한 반도체 소자 제조에 널리 활용되고 있으며, 점차 그 응용 분야를 넓혀가고 있다. 특히 thermal 방식의 잉크젯 피린팅 기술은 etching, thin film process, lithography등의 반도체 공정 기술을 이용하여 제작할 수 있기 때문에, 현재 잉크젯 프린팅 기술은 대부분 thermal 방식을 체택하고 있다. 이러한 thermal 잉크젯 프린팅 방법에서는 잉크를 토출시키기 위하여, 전기적 에너지를 열에너지로 전환하는 전자저항막층이 필수적으로 필요하게 되는데, 이러한 전자저항막층은 수백도가 넘는 고온 및 잉크와 접촉으로 인한 부식 및 산화 문제가 발생할 수 있는 열악한 환경에서 사용되므로, Ta, SiN과 같은 보호층을 필수적으로 필요로 한다. 그러나 최근 잉크젯 프린터의 고해상도 고속화, 대면적 인쇄성 등과 같은 다양한 요구 증가에 따라, 잉크젯 프린터의 저전력 구동이 이슈로 떠올라 열효율에 방해가 되는 보호층을 제거할 필요성이 제기되고 있다. 지금까지는 Poly-Si, $HfB_2$, TiN, TaAl, TaN _0.8 등의 물질들이 잉크젯 프린터용 전자저항막 물질로 연구되거나 실제로 사용되어져 왔으나, 이러한 물질들을 보호층을 제거하는 경우 쉽게 산화되거나, 부식되는 문제점을 가지고 있다. 따라서, 기존 전자저항막의 기능을 만족시키면서, 산화나 부식에 대한 강한 내성을 가져 보호층을 제거하더라도 안정적으로 구동이 가능한 하이브리드 기능성(히터 + 보호층)을 가지는 잉크젯 프린터용 전자저항막 물질의 개발이 시급한 실정이다. 본 연구에서는 자기조립특성을 가져 정밀제어가 가능한 원자층증착법(Atomic Layer Deposition)을 이용하여 원자/나노 단위의 미세 구조 컨트롤을 통해 내열 내산화 내부식성 저온도저항계수를 동시에 가지는 다기능성 전자저항막을 설계 및 개발하고자 하였다. 전자저항막 개발을 위하여 우수한 내부식 내산화성을 가지고 결정립 크기에 따른 온도저항계수 조절이 가능한 platinum group metal들과 전기 저항 및 내열성 향상을 위한 물질의 복합구조막을 원자증증착법으로 증착하였다. 또한, 전자저항막 증착시 미세구조와 공정 변수가 내부식성, 내산화성, 그리고 온도저항계수에 미치는 영향을 체계적으로 연구하여, proto-type의 inkjet printhead를 구현하였다.