• 펄프종이기술
• /
• 제34권4호
• /
• pp.16-21
• /
• 2002

It was observed that drying temperature and curing time in the paper coating process as well as Tg of the latex used as a binder, greatly affected the properties of the coated paper such as roughness, paper and print gloss, K & N ink drop, and ink set-off. The higher drying temperature induced faster water evaporation and change in binding density, which caused an increase in paper roughness, ink gloss and ink set-off, but decrease in paper gloss and K & N ink drop. The increased curing time promoted latex filming and redistribution of the binder in coating layer. This increased pick strength and ink gloss, but decreased ink trapping. Finally, the higher Tg of the latex showed the wider changing range of these properties.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2003년도 춘계학술발표논문집
• /
• pp.54-69
• /
• 2003

Print gloss is an important attribute of the final printed product. While past work has looked at the influence of key aspects of the coating structure on print gloss, a systematic study has not been reported. The coating roughness, porosity, and pore size are changed by using various combinations of coating materials and by calendering against rough plastic sheets. The print gloss is measured every tenths of a second right after printing, a few minutes after printing, and a few days afterwards. Roughness and porosity affect the print gloss for the first two seconds: this result shows that they influence the ink-film splitting event. Once ink film starts to level, roughness and pore size influences the level of print gloss within the first ten seconds after printing. Porosity modifies the evolution of print gloss for the next few minutes. The decrease in gloss at long times is found to correlate to surface roughness.

• Journal of Forest and Environmental Science
• /
• 제18권1호
• /
• pp.97-105
• /
• 2001

The main objective of this study was to investigate effects of pigment mixed with different ratio on the double coated paper. Mineral pigments such as clay and ground calcium carbonate(GCC) as well as hollow sphere plastic pigment were used to evaluate the physical, optical properties and printabilities of double coated paper. The physical properties such as gloss and smoothness, and the printability(ink gloss) of double coated paper were measured to evaluate the effects of the bottom layer on improving the properties of top layer. The data indicated that the usage of hollow sphere plastic pigment for the bottom layer coating improved the surface properties of double coated paper, and that ink gloss was significantly influenced by the structure of bottom layer even when hollow sphere plastic pigment was used for the bottom layer coating.

• 펄프종이기술
• /
• 제44권3호
• /
• pp.41-48
• /
• 2012

Materials used for the inks in the printing industry is an important material following the paper. The composition of the ink is pigment and organic solvents. However, Ink is used in a variety of chemicals, they are classified as non-green. Therefore, rosin-modified phenolics manufactured by the reaction of phenol and formaldehyde can take the place of eco-phenol free resin and by experiment density, gloss, trapping, contrast and dot gain of printing has been studied as printability. The result of study can support that the properties of printing using eco-phenol free resin such as density, gloss, contrast and trapping is similar to existing ink. In the part of dot gain, the result is excellent. So we were thought to be able to improve some characteristics such as dispersion of black ink, that will be possible for the field applicability.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2005년도 추계학술발표논문집
• /
• pp.243-250
• /
• 2005

• 펄프종이기술
• /
• 제34권2호
• /
• pp.22-31
• /
• 2002

In this paper, PVA(polyvinylalcohol), oxidized starch and SBR latex were used as binders for ink-jet printing papers, and their effects of the type and blending ratio of binders on ink-jet printing properties were compared. In case of coating color using PVA mainly used for a binder in ink-jet printing, spreading of printed letters decreased and excellent images were manifested resulting from strong hydrophilic of PVA. However, increasing solids content of coating color was somewhat limited because of the interaction of PVA and functional groups in silica as well as high molecular weight of PVA. When oxidized starch and SBR latex were mixed with PVA at desirable ratio to solve these problems, runnability in coating process was improved and good printing properties were shown. Gloss was improved when latex was used along with PVA as a binder because of the thermoplastic property of the latex. From this result, possibilities of high solids content and high gloss ink-jet printing papers were investigated.

• 펄프종이기술
• /
• 제33권3호
• /
• pp.29-36
• /
• 2001

This paper was made to evaluate the effect of the blending ration of GCC and No. 1 clay on the printability by investigating the structure of pore such as the pore rate, the number of pores, pore size and distribution of coated paper. The coated structure is mainly depended on the results of correlation between pigment and binder. It means that the structure of the pore occurred is chiefly affected by the blending ratio of GCC and No. 1 clay. This physical properties of the pore have a close relation with ink set-off associated with the drying rate and the penetration in ink into base paper and with printing gloss. Therefore it was needed to find out how the pore structure and the printability will be changed by modifying the blending ratio of GCC and No. 1 clay to vary the pore structure of coated paper. Below are the results of measurement: As the blending ratio of clay going up, water retention, sedimentation volume. smoothness, and paper gloss were increased, but relatively brightness and opacity were decreased. Pore rate was the highest at the blending ratio of No. 1 clay to GCC, 70:30. In this case, average pore radius was also increased. Ink receptivity and K&N ink receptivity were improved with the increase of the blending ratio of GCC, where was, ink setting was vice versa. No difference was observed in the weight of ink, but ink repellance decrease with the decrease of blending ratio of GCC.

• 펄프종이기술
• /
• 제34권3호
• /
• pp.53-58
• /
• 2002

This paper was performed to investigate the effect of pore structure on ink residual behavior. To prepare different coating structures as substrates against inks, fine, medium and coarse calcium carbonate were used in the coating color. It is well known ink properties can affect to print qualities. After printing on the coated paper, ink layer can consider as third structure addition to paper and coating layer. To compare effect of ink properties on the surface structure and print qualities, several properties of ink were also adopted as raw material. Particle size of pigment effect on gloss evaluation of coated paper increased with calendering. It was shown that ink transfer rate increased as surface of the sample was smooth. The ink contained low viscosity resin evaluated more print gloss. Finer pigment particle size, smaller pore size and higher porosity. Pore volume of coated paper was slightly decreased with printing as the coating was prepared with the finest particle size. However, it founded that ink resin could not affect on pore volume and distribution of printed paper

• 펄프종이기술
• /
• 제34권1호
• /
• pp.22-29
• /
• 2002

The coated paper was greatly affected by the basic physical properties of the binder as well as the amount of the coating formula. High glass transition temperature (Tg) of the styrene-butadiene (SB) latex, selected as the binder in our study, gave the high stiffness to the coated paper, but lowered the binding force and print gloss. The average particle size of the SB latex also greatly affected to the coated paper so that the smaller particle size improved the rheological property of the coating formula and increased the binding force and print gloss. Another property of the SBR latex, gel content, was important because when its value was small, the latex was easily deformed at the high temperature and increased air permeability to the coated paper. Therefore, the lower gel content consequently resulted in the higher blistering resistance, especially in the web paper. The larger portion of the SB latex in the coated formula improved the binding force and print gloss, but decreased the ink set-off and ink-trapping to the coated paper. The heavier coating improved optical properties such as opacity, paper gloss and paper smoothness, to the coated paper.

• 펄프종이기술
• /
• 제34권5호
• /
• pp.1-17
• /
• 2002

The immobilization and consolidation of the model coatings based on the plastic pigment and latex binder of known particle sizes were theoretically Studied in terms of the dense random packing of binary spheres and varying extent of latex film shrinkage. The porosity of the model coatings was calculated based on three proposed latex shrinkage models: Maximum, Minimum, and Linearly Decreasing Latex Shrinkage. The increasing extent of latex shrinkage was calculated up to the critical pigment volume concentration(CPVC) as a function of plastic pigment volume fractions, and the maximum latex shrinkage was estimated from the CPVC. Also, the number of pores and the average equivalent spherical pore diameters were calculated based on those proposed models. The opacity and gloss of the model coatings on polyester films were measured and their porosity was also determined by a simple coat weight-thickness method. As expected, various coating structure-property-composition relationships, such as opacity, gloss, porosity, etc., were shown to exhibit sharp transitions near the CPVC. The CPVC values determined by the opacity, gloss, and porosity vs. PVC relationships, respectively, agreed very well with each other. Especially, the CPVC's determined by the opacity and porosity vs. PVC curves were identical. The comparison between the theoretically calculated and experimental porosity values showed that the intermediate value between the maximum and minimum latex shrinkage would best fit the experimental porosity data. The effect of plastic pigment particle size on the optical properties and porosity of model coatings was also studied and it was observed that the coating opacity and porosity increased with increasing plastic pigment particle size, but the gloss decreased. The ink gloss of the uncalendered model coatings applied onto commercial sheet offset coated papers was shown to be affected by both the coating gloss and porosity: the higher the coating gloss, the higher the ink gloss, but the higher the coating porosity, the lower the ink gloss. Their printability was also studied in terms of the number of passes-to-fail and the rate of ink setting as a function of both plastic pigment volume fractions and plastic pigment particle sizes. A minimum crack-free temperature(MCR) of latex-bound coatings was proposed to better predict the behaviors of latexes as coating binders. The wet state of model coating dispersions, the surfaces of consolidated model coatings, and their internal structure were examined by both electron and atomic force microscopy, and their micrographs were found to be consistent with our immobilization and consolidation models.