• 한국자동차공학회논문집
• /
• 제11권5호
• /
• pp.43-49
• /
• 2003

The common-rail fuel injection system is becoming a common technology for High Speed Direct Injection(HSDI) diesel engines. The injection timing and rate are important factors for combustion control and pollutants formation mechanisms during engine operation. This paper introduces an estimation methodology of the injection timing and rate of a common-rail injector for HSDI diesel engines. A sliding mode observer that is based on the nonlinear mathematical model of the common-rail injector is designed to overcome the model uncertainties. The injector model and the estimator we verified by relevant injection experiments in an injector test bench. The simulation and the experimental results show that the proposed sliding mode observer can effectively estimate the injection rate of the common-rail injector.

• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.87-94
• /
• 2003

Recently, LPLi(Liquied-Phase LPG injection) system is studied for the new stringent emission regulations. But , there are some problems to be solved such as injector tip icing and fuel leakage for LPLi system development. In this paper, the icing problem near injector tip which leads to difficulty of accurate A/F control was studied and reported. Icing of injector tip and port wall was observed at all the cases in this study regardless of injection duration and angle, air humidity change. The spray angle of LPLi was observed approximately two times wider than that of Gasoline injection. This makes the LPLi spray collide with intake port around injector tip. Temperature of the wetted area was decreased and icing of water vapor contained in intake air because of evaporation of the fuel film. The ice of the injector tip and port wall is also affected by the materials related to heat transfer.

• 한국전자통신학회논문지
• /
• 제8권2호
• /
• pp.279-284
• /
• 2013

본 논문에서는 경제적이고, 채널 확장성이 용이하며, 다양한 성능시험에 대응이 가능한 솔레노이드 타입의 인젝터 컨트롤러를 연구 개발하고 그 성능을 평가하였다. 개발된 컨트롤러는 임베디드 시스템에 기반을 두고 있으며, 인젝터에서 고압으로 분사되는 연료의 분사 타이밍 및 분사량에 대한 정밀제어는 물론 솔레노이드의 전기적인 특성을 측정하여 인젝터의 성능평가도 가능하다. 또한, 부가적으로 인젝터의 분무 형태를 정밀하게 촬영할 수 있는 광원과 초고속 카메라의 정밀시간제어도 동시에 가능하도록 하였다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.33-34
• /
• 2006

In this study, a prototype piezo-driven Injector. as a new method driven by piezoelectric energy, has been designed and fabricated based on the concept of inverse piezo-electric effect to overcome the major drawbacks of conventional solenoid-driven injector with a fixed and slow control of injection rate. The effects of an electric control between the solenoid valve and piezo-ceramic stack for injector needle's driving on the dynamic characteristics were usually investigated. We found that this piezo-electric actuator has the main advantage to drastically reducing the time of injector nozzle opening, as well to exert higher force output levels.

• 한국분무공학회지
• /
• 제5권2호
• /
• pp.68-74
• /
• 2000

A this experimental study is executed to analyze spray characteristics for air-shrouded injector and 4hole 2spray type injector used in a gasoline engine. Since spray parameters including spray penetration and angle, SMD, and atomization characteristics are very important to increase the engine performance, the image processing algorithm for measuring the non-spherical spray diameter is developed. Spray characteristics of the air-shrouded injector(2hole 2spray) and 4hole-2spray injector are analyzed respectively by this digital image processing method. Effective spray characteristics to injectors is derived from this experimentation and obtained the design guide for gasoline injector.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.454-459
• /
• 2003

The one of the most important subject to develop a LPDi engine is to suppress the generation of bubble inside LPG direct injector. For the purpose of this, in this study, the analogy visualization injector to visualize the generation and behavior of bubble, is manufactured and the bubbling phenomenon and behaviors are visualized and studied. The bubble inside the injector is generated at injection hole and after rising by buoyancy, it disappear around the top of a nozzle. The number of bubble generated is little changed regardless of the lapse of time but it is increased remarkably as the temperature around the injector is increased. With injection, the temperature around the injector at which the bubble is generated in_cylinder is much lower than that without injection because the transient pressure drop of fuel by injection.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.236-239
• /
• 2017

스크램제트 엔진 개발의 일환으로 injector에 대한 연구를 수행하였다. 실험에는 Barbotage injector를 사용하였다. Injector의 분무 특성을 확인하기 위해 물을 주 연료로 공급하였고 액체의 미립화를 위하여 질소를 공급하였다. 실험 설비는 한국항공우주연구원의 분무 시험 장치와 PDPA를 사용하였다. 실험 결과 기체 압력 변화와 분무 거리가 미립화되는 정도에 큰 영향을 끼치는 것을 알 수 있었다.

• International Journal of Aeronautical and Space Sciences
• /
• 제3권1호
• /
• pp.1-8
• /
• 2002

A numerical analysis was performed on the fluid flow in injector orifice of a liquid rocket engine. The present computational code was verified against the published data for turbulent flow in a pipe with a sudden expansion-contraction. Considered were the parameters for the flow analysis in an injector orifice: Reynolds number, ratio of mass flow rate of the injector orifice and inlet flow rate, and slant angle of the injector orifice. The discharge coefficient increased slightly as the Reynolds number increased. The slant angle of the injector changed critically the discharge coefficient. The discharge coefficient increased by 7% when the slant angle changed from $-30^{\circ}$ to $30^{\circ}$ The ratio of mass flow rate had relatively little impact on the discharge coefficient.

• 한국분무공학회지
• /
• 제19권1호
• /
• pp.9-14
• /
• 2014

Performance of DI diesel engine with high-pressure fuel injection equipment is directly related to its emission characteristics and fuel consumption. So, the electro-hydraulic injector for the common-rail injection system should be designed to meet the precise high fuel delivery control capability. Currently, most high pressure injector in use has a needle driven by the solenoid coil energy or the piezo actuator controlled by charge-discharge of output pulse current. In this study, macroscopic spray approaching method was applied under constant volume chamber to research the performance of three different injectors : solenoid, indirect-acting piezo and direct-acting piezo type for CR direct-injection. LED back illumination for Mie scattering was applied on the liquid spray visible of direct-acting piezo injector, including hydraulic-servo type solenoid and piezo-driven injectors. As main results, we found that a direct-acting piezo injector had better a spray tip penetration than hydraulic-servo injectors in spray visualization.

• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.93-100
• /
• 2005

Stringent emission regulations and increasing demands on reductions of noise and vibration of common rail direct injection (CRDI) diesel engines lead to the advent of piezo-actuated injectors. Compared with solenoid-actuated injectors, piezo-actuated injectors generate greater force and give faster response time, resulting in more accurate and faster injections. The accurate and fast response of an injector can offer an opportunity to control the combustion process and pollutant formation. In this study, the mathematical model of a piezo-actuated injector is developed. An estimator of the injection rate of the piezo-actuated injector is designed based on this model. The sliding mode theory is applied to the estimator design in order to overcome model uncertainties. The injector model and the estimator are verified by the injection experiments in an injector test bench. The simulation and the experimental results show that the proposed sliding mode observer can effectively estimate the injection timing and the injection rate of the piezo-actuated injector.