• 한국분무공학회지
• /
• 제10권1호
• /
• pp.24-34
• /
• 2005

Injection technology is one of the important technologies in a diesel engine. Many studies have done on the injection system. In this study, the fuel chamber geometry, the orifice ratio and the needle lift of the injection valve for a marine diesel engine are varied, and simulated. The result shows that the nozzle hole size has influence on the rail pressure and injection duration sensitively. The decrease of the static pressure at the nozzle hole entrance and the increase of the dynamic pressure on the outlet surface are occurred with the increase of the nozzle hole diameter. The highest dynamic pressure of the outlet was occurred at the needle lift of 0.4mm and the nozzle hole diameter of 0.328mm in this test nozzle.

• 한국수자원학회논문집
• /
• 제48권10호
• /
• pp.869-877
• /
• 2015

해수침투 방지나 대수층 인공함양을 위하여 다수의 관정을 통하여 대수층으로 물을 주입하는 공법이 있다. 이러한 공법의 경우 소기의 목적을 달성하기 위해서는 관정의 위치와 주입량, 그리고 결과되는 관정의 지하수위 등이 별도의 지하수 모델링을 통하여 결정된다. 주입수는 통상 관망을 통하여 관정으로 공급되는 데 이 때 관망에는 관정별 주입량을 조절하기 위한 밸브가 설치된다. 본 연구에서는 다수의 주입 관정이 연결된 관망에서 사전에 산정된 주입량 분포를 준수하기 위한 밸브 개도와 주입관망 가동에 필요한 펌프 최소 소요양정 산정방안을 제시하였다. 본 연구결과는 주입군정 운영의 정밀도를 향상시키는 데 기여할 수 있다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.67-68
• /
• 2006

This study suggests a precision flow control system that enables fluid injection of a few grams at a time in a few ms time duration. The fluid injection system suggested here consists of a high pressure fluid pump, a 3 way 3 position directional control valve, an injector and an orifice. The orifice is located between the directional control valve and the injector. By supplying current signal to the directional control valve, the prescribed small amount of fluid can be supplied to a plant through the injector. The control robustness of the suggested system against the disturbances like the pressure change in a plant and the viscosity variation of the injected fluid is secured easily by using an orifice with very small inside diameter and setting the supply pressure with comparatively high value. The control performances of the suggested system are verified by numerical simulations and experiments. The outcomes of this research could be applied to the common rail injection control of lubrication oil for large size marine diesel engines, and other industrial plants.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.172-179
• /
• 1998

Valve lifter namely tappet is supported by lifter hole which is located upper side of camshaft in cylinder block transforms rotatic mvement of camshaft into linear movement and helps to open and shut the en-gine valve as an engine parts. The face of valve lifter which is continuously contacting with camshaft brings about abnormal wears such as unfair wear and early wear because it is severely loaded in the valve train system. These wears act as a defect like over-clearance and cause imperfect combustion of fuel during the valve lifting in the combustion chamber. Consequently this imperfect combustion makes the engine out-put decrease and has cause on air pollution. To prevent these wears therefore The valve lifter cast in me-tal developed into SiC ceramics valve lifter which has an excellence in wear and impact resistance As a results the optimum process conditions like injection condition mixture ratio and debonding process could be established. After sintering fine-sinered dual microstructure in which prior ${\alpha}$-SiC matches well with new SiC(${\beta}$-SiC) produced by reaction among the ${\alpha}$-SiC carbon and silicon was obtained. Based on the study it is verified that mechanical properties of SiC valve lifter are excellent in Vickers hardness 1100-1200 bending strength (300-350 Pa) fracture toughness(1.5-1.7 Mpa$.$m1/2) Through engine dynamo test-ing SiC valve lifter and metal valve lifter are examined and compared into abnormal phenomena such as early fracture unfair and early wear. It is hoped that this research will serve as an important springboard for the future study of heavy duty diesel engine parts developed by ceramics which has a good wear resis-tance relaibility and lightability.

• 에너지공학
• /
• 제19권1호
• /
• pp.32-38
• /
• 2010

The objective of the research was to study the effects a Miller cycle. The engine was dedicated to natural gas usage by modifying pistons, fuel system and ignition systems. The engine was installed on a dynamometer and attached with various sensors and controllers. Intake valve timing, engine speed, load, injection timing and ignition timing are main parameters. Miller Cycle without supercharging can increase brake thermal efficiency 1.08% and reduce brake specific fuel consumption 4.58%. The injection timing must be synchronous with valve timing, speed and load to control the performances, emissions and knock margin. Throughout these tested speeds, original camshaft is recommended to obtain high volumetric efficiency.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.110-114
• /
• 2001

A numerical analysis has been perfonned to estimate the effect of turbulent penetration and thermal stratified flow in the branch lines piping. This phenomenon of thermal stratification are usually observed in the piping lines of the safety related systems and may be identified as the source of fatigue in the piping system due to the thermal stress loading which are associated with plant operating modes. The turbulent penetration length reaches to $1^{st}$ valve in safety injection piping from reactor coolant system (RCS) at normal operation for nuclear power plant when a coolant does not leak out through valve. At the time, therefore, the thermal stratification does not appear in the piping between RCS piping and $1^{st}$ valve of safety injection piping. When a coolant leak out through the $1^{st}$ valve by any damage, however, the thermal stratification can occur in the safety injection piping. At that time, the maximum temperature difference of fluid between top and bottom in the piping is estimated about $50^{\circ}C$.

• 대한한의학회지
• /
• 제43권3호
• /
• pp.164-180
• /
• 2022

Objectives: The purpose of this study was to evaluate the effects of shenfu injection on myocardial protective effects after mitral valve replacement surgery. Methods: We searched four international databases (PUBMED, Embase, Web of Science and CNKI) and three domestic electronic databases (OASIS, RISS and NDSL) for relevant studies. We used following keywords 'shenfu', 'valve replacement', 'mitral valve' at PUBMED, Embase and Web of Science; '二尖瓣', '参附注射液', '瓣膜' at CNKI and '이첨판', '판막', '삼부' at domestic databases. The search range included randomized controlled trials. When appropriate, meta-analyses were performed. Results: Seven randomized controlled trials were selected. All studies used Shenfu injection after mitral valve replacement surgery. We analyzed myocardial damage, cardiac function, patients' recovery rate, with various evaluation indicators. We also used meta-analysis for CK-MB, cTnI, MDA and voluntary recovery of heartbeat. CK-MB was analyzed in two subgroups: 8 hours and 24 hours after surgery. Std was -2.34(95% CI -4.10, -0.58) for 8 hours and -1.95(95% CI -4.79 to 0.88) for 24 hours. 8 hours showed statistically significant difference. cTnI appeared significant decrease with Std of -2.13(95% CI -2.60, -1.66). MDA showed significant decrease with Std of -0.95(95% CI -1.43 to -0.47). Voluntary recovery of heartbeat significantly increased with the odd ratio of 4.34(95% CI 1.76, 10.70). Conclusions: We suggest that Shenfu injection after Mitral valve replacement surgery may have significant myocardial protective effects in terms of reducing myocardial damages, reactive oxygen species, increasing cardiac function and patients' recovery after surgery. However, the evidence is limited, further research is required.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.389-396
• /
• 2017

Restorations of automotive parts have been done ever since the first vehicle was produced. Because the most expensive parts of a vehicle are in the engine system, there have been various restoration methods developed for engine parts. In the case of commercial diesel engines, the fuel injection device is a key and expensive component. It also has a significant effect on vehicle performance. In particular, reduced engine power and increased exhaust gas emissions may result from mechanical damage due to abrasion of the spill valve in the fuel injection system of a diesel engine. In this paper, restoration techniques for damaged parts are applied to restore the abrasion of a spill valve of fuel injection, also called as the "unit injector", of commercial diesel engines. In order to recover the damage, optimized polishing techniques using hard-metal and coating processes are applied. To evaluate restoration techniques for the spill valve, performance and durability tests are performed on a test bench.

• 한국분무공학회지
• /
• 제15권1호
• /
• pp.1-7
• /
• 2010

As world attention has focused on global warming and air pollution, high efficiency diesel engines with low $CO_2$ emissions have become more attractive. Premixed diesel engines in particular have the potential to achieve the more homogeneous mixture in the cylinder which results in lower NOx and soot emission. Early studies have shown that the operation conditions such as the EGR, intake conditions, injection conditions and compression ratio are important to reduce emissions in a PCCI (Premixed Charge Compression Ignition) engine. In this study a modified cam was employed to reduce the effective compression ratio. While opening timing of the intake valve was fixed, closing timing of the intake valve was retarded $30^{\circ}$. Although Atkinson cycle with the retarded cam leads to a low in-cylinder pressure in the compression stroke, the engine work can still be increased by advanced injection timing. On that account, we investigated the effects of various injection parameters to reduce emission and fuel consumption; as a result, lower NOx emission levels and almost same levels of fuel consumption and PM compared with those of conventional diesel engine cam timing could be achieved with the LIVC system.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.425-432
• /
• 2001

Fluidic valve is adopted in APR1400 to control passively the flow rate of cooling water from the safety injection tank. It is necessary to establish independent evaluation guideline for the flow characteristics of fluidic valve in order to secure safety. Three dimensional numerical model for fluidic valve is developed and numerical results are compared with experimental data obtained at KAERI in order to verify numerical simulation. Also influence of the grid number and the turbulence model were investigated. In addition, variation of flow rate is investigated at various elapsed times after valve operating, and flow characteristics are analyzed at low and high flow rate conditions, respectively.