• Design & Manufacturing
• /
• v.8 no.1
• /
• pp.19-22
• /
• 2014

Today, looking at the trend of product development, interests of injection technology to reduce weldline are growing because of increases of polymer composite materials that containing functional elements and demand of no-painted injection in accordance with environmental regulations. In this paper, surface temperatures of mold increased using high temperature gas for elimination of weldline and characteristics of weldline are analyzed according to mold temperature($60^{\circ}C{\sim}120^{\circ}C$).

• Design & Manufacturing
• /
• v.16 no.4
• /
• pp.67-74
• /
• 2022

Injection molding is a cyclic process comprising of cooling phase as the largest part of this cycle. Providing efficient cooling in lesser cycle times is of significant importance in the molding industry. Recently, lots of researches have been done for rapid cooling of a hot-spot area using CO2 in injection molding. The CO2 flows under high pressure through small, flexible capillary tubes to the point of use, where it expands to create a snow and gas mixture at a temperature of -79℃. The gaseous CO2 removes heat from the mold and releases it into the atmosphere. In this paper, a CO2 cooling module was applied to an injection mold in order to cool a large area cavity uniformly and quickly, and the cooling performance of the injection mold was investigated. The product was a high-curvature molded part with a molding area of 300x100mm. Heat cartridges were installed in a stationary mold, and CO2 cooling module was inserted inside a movable mold. Through structural analysis, it was confirmed that the maximum deformation of mold with CO2 cooling module was 0.09mm. A CO2 feed system with a heat exchanger was used for cooling experiments. The CO2 was injected into the holes on both sides of the supply pipe of the cooling module and discharged through hexagon blocks to cool the mold. It took 5.8 seconds to cool the mold from an average temperature of 140℃ to 70℃. Through the experiment using CO2 cooling module, it was found that a cooling rate of up to 12.98℃/s and an average of 10.18℃/s could be achieved.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.316-319
• /
• 2002

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameters and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced strongly the shrinkage of injection molded part.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.1
• /
• pp.84-91
• /
• 1997

In producing moldings by using an injection mold, several variables such as the metal mold and the condition of injection molding should be selected properly in order to obtain good quality of moldings. In this study, focussed are the mechanical properties of injection moldings, since many researches on injection have been focussed mainly on the molding quality, injection pressure, and bulk temperature but the properties of injection moldings have not been studied extensively. The mechanical properties of present injection moldings can be improved simply by changing the molding material and the injection conditon without changind the metal mold. To have the final products meet the specified molding quality and mechanical properties at the same time, the bulk temperature of injection, pressure variation, volumetric shrinkage, stress, and cooling should be analized by CAE(computer aided engineering) after injection mold design. In this paper, the effects of dischare condition on mechanical properties of injection moldings are studied by testing the moldings which are injected by varying injection conditions.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.323-327
• /
• 1993

Mold-making industry demands currently to reduce the tooling costs and time in mold making, and to improve the productivity and quality in injection molding process. These problems can be easily removed by laminated injection mold which is made with metal sheets prepared by laser cutting and bonded by brazing. Comparing withthe conventional mold making technology which mainly depends on the machining, this new technologyenables an arbitary design of cooling circuit without anyrestrictions of geometry. So it brings about high production rates of the injection molding processes. This paper estimate the conventional and laminated injection mold making process with a simple molding, and also the cooling efficiencyof thoes two kinds of mold with the filling and cooling analysis. The results show that the laminated injectionmold has much shorter tooling time, uniform mold temperature, and shorter cooling time in injection molding process.

• Design & Manufacturing
• /
• v.15 no.3
• /
• pp.56-61
• /
• 2021

The increase in automation facilities in the injection molding industry is a very important process control item. The most important item when constructing an unmanned machine using a take-out robot is the "mold opening stroke" of the mold. The injection molding machine control method is divided into hydraulic type and electric type, and there have been few studies on the mold opening distance according to the control method. In this study, the correlation was confirmed by increasing the injection speed to 20, 50, 80, and 100% for the three types of hydraulic control method, open loop and close loop, and electric control method. Through the experiment, the following results were obtained. (1) It can be seen that the reproducibility is excellent with the electric, close loop, and open loop control methods. (2) When the injection speed is set to 50%, the mold opening distance is 263.10~263.27 mm, which is the most reproducible. (3) As a result of ANOVA, both injection speed and mold opening distance showed a significant difference in the hydraulic control method (p<0.05), but it was verified through experiments that there was no significant difference in the electric control method. Based on these results, when electric control is selected rather than hydraulic control, the reproducibility of the mold opening distance is excellent, so it is thought that the taking-out robot can take the object out of the mold more safely.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.155-158
• /
• 2008

Flow imbalance among the cavities was often observed in multi-cavity mold. The flow imbalance affects on the dimensions and physical properties of molded articles. First of all, the origin of flow imbalance is geometrical imbalance of delivery system. However, even the geometry of delivery system is balanced the cavity imbalance is being developed. This comes from the temperature distribution in the cross-section of runner, which is affected by the operational conditions. In this study, experimental study of flow imbalance has been conducted for various injection speeds. This study also suggests new runner design to eliminate flow imbalance in multi-cavity injection mold. Simulation and experimental results showed suggested new designed runner could eliminate or reduce flow imbalance in multi-cavity injection mold.

• Journal of the Korea Safety Management & Science
• /
• v.6 no.4
• /
• pp.183-193
• /
• 2004

The injection mold industry has strong relationship with many other industries. In the injection mold industry, the harmonious collaboration of the order-making companies, the mold-making companies, and the molded-parts making companies, which are distantly located, is very important. In this study, a web-based collaboration system is developed for the purpose. It offers the criterion to select appropriate production companies. It also tries to minimize the production cost of the mold design by distributing and evaluating the design information. The developed system is constructed using various recent web-programming tools.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.5
• /
• pp.225-231
• /
• 2003

The injection molding is a traditional manufacturing method that can make plastic parts by just one time in mold. Therefore, the injection molding has become one of a manufacturing method, which is widely applied in a producing of plastic products. Nowadays, to use of plastic parts has increased and plastic product-model using term has been shorten. By these reasons, using term of a injection mold has fast been reduced. These produced molds will be disused and leaved in a storage after a regular term to use it. These leaved molds are sometime sold as scrap iron. But, these molds have lots parts for recycling except special parts for example, cavities, cores and eject pins, etc. In this research, we investigated when the cavity and core of in injection mold would be changed, the injection mold could be recycled. We suggested the structures and standardizations for recycling of a moldbase. We also developed a program in which can be used when the recycling moldbase design in the Auto-CAD with the recycling standards. We called this program as the Recy-Mold. For the availability of the program and moldbase structure fur the recycling standards, we experimented a used mold for automobile lens, which was remanufactured by the recycling standard. The results of this test showed feasibility for the recycling mold.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.11
• /
• pp.84-90
• /
• 2007

In this study, design and manufacturing of plastic injection mold with cavity pressure/temperature sensors were performed fur tensile test specimen. International standard system for plastic tensile specimen was applied to design an injection molding system. Cavity pressure and temperature sensors were placed on the side of fixed platen of the injection mold to prevent them from external impact damage. Injection molding experiments with variations of injection speed and melt temperature were performed and then tensile test of the manufactured polycarbonate specimens was also performed. It was shown that injection molding processing parameters can have effect on the mechanical properties of the plastic injection molded part.