• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.2
• /
• pp.126-129
• /
• 2021

We fabricated plate typed shunt resistors composed of carbon nanotube (CNT) and metal alloy for measuring DC current. CNT plates were prepared from dispersed CNT/Urethane solution by squeezing method. Cu/Ni alloys were prepared from composition-designed alloy wires for adjusting the temperature coefficient of resistance (TCR) by pressing them. As well, we fabricated a hybrid resistor by squeezing the CNT/Urethane solution on the metal alloy plate directly. In order to confirm the composition ratio of the Cu/Ni alloy, we used an energy-dispersed X-ray spectroscopy (EDX). Cross-section and surface morphology were analyzed by using a scanning electron microscopy (SEM). Finally, we measured the initial resistance of 2.35 Ω at 25℃ for the CNT paper resistor, 7.56 mΩ for the alloy resistor, and 7.38 mΩ for the hybrid resistor. The TCR was also measured to be -778.72 ppm/℃ at the temperature range between 25℃ to 125℃ for the CNT paper resistor, 824.06 ppm/℃ for the alloy resistor, and 17.61 ppm/℃ for the hybrid resistor. Some of the hybrid resistors showed a near-zero TCR of 1.38, -2.77, 2.66, and 5.49 ppm/℃, which might be the world best-value ever reported. Consequently, we could expect an error-free measurement of the DC current using this resistor.

• Geophysics and Geophysical Exploration
• /
• v.24 no.4
• /
• pp.171-179
• /
• 2021

We outline a process for estimating Cole-Cole parameters from time-domain induced polarization (IP) data. The IP transients are all inverted to 2D Cole-Cole earth models that include resistivity, chargeability, relaxation time, and the frequency exponent. Our inversion algorithm consists of two stages. We first convert the measured voltage decay curves into time series of current-on time apparent resistivity to circumvent the negative chargeability problem. As a first step, a 4D inversion recovers the resistivity model at each time channel that increases monotonically with time. The desired intrinsic Cole-Cole parameters are then recovered by inverting the resistivity time series of each inversion block. In the second step, the Cole-Cole parameters can be estimated readily by setting the initial model close to the true value through a grid search method. Finally, through inversion procedures applied to synthetic data sets, we demonstrate that our algorithm can image the Cole-Cole earth models effectively.

• Journal of Korea Trade
• /
• v.25 no.3
• /
• pp.48-64
• /
• 2021

Purpose - This study examined the effect of tariff cuts on productivity in Korea's manufacturing industries and the effect of initial productivity level before tariff cuts on productivity improvement after tariff cuts. We also attempted to identify whether import-driven or export-driven factors are more important for productivity improvement, especially in low productivity industries. Design/methodology - Since tariff reduction is a policy decision that can affect cross-industry, its impact is spread across all industries beyond the scope of a single firm through the input and output network of industry structure. Accordingly, we proposed a new method to measure the change in productivity to reflect the impact of tariff cuts across industries. Through an Armington CGE analysis, changes in endogenous variables can be directly measured after the exogenous shock of tariff reduction, and the amount of movements in productivity triggered by tariff cuts can also be calculated. We can thus assess the effectiveness of exogenous policy, such as tariff cuts, through the difference between the benchmark and counterfactual values of endogenous variables. Findings - This study confirmed that tariff reduction positively affected productivity improvement in Korea's manufacturing industries. It also confirmed that productivity gains occur in Korea's leading export industries. Finally, greater productivity gains were recorded in the group with additional high-export-share or high-import-share conditions for low productivity industries. These results are, in a limited sense, consistent with the existing studies that emphasize the importance of exports and imports on productivity improvement, especially for low productivity industries. Originality/value - The results of our experiments are different from those of non-CGE studies, which measure the industry-level change in productivity with dummy coefficients, in terms of directly calculating the amount of change in productivity. In addition, we propose that the Armington CGE model is more appropriate than the Melitz CGE model to directly measure the productivity after tariff cuts. This is because the Melitz CGE model assumes the given specific productivity density, which does not change after an overall drop of tariffs. To the best of our knowledge, this approach to directly calculating productivity by reflecting the impact of tariff reduction across industries through CGE analysis, is unprecedented in this literature.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.6
• /
• pp.492-505
• /
• 2022

This study is a study on the results of improving the logic to effectively transmit and decode compressed data in real time by improving the encoding and decoding performance of BL-beta codes that can be used for lossless real-time transmission of IoT sensing data. The encoding process of BL-beta code includes log function, exponential function, division and square root operation, etc., which have relatively high computational burden. To improve them, using bit operation, binary number pattern analysis, and initial value setting of Newton-Raphson method using bit pattern, a new regularity that can quickly encode and decode data into BL-beta code was discovered, and by applying this, the encoding speed of the algorithm was improved by an average of 24.8% and the decoding speed by an average of 5.3% compared to previous study.

• The korean journal of orthodontics
• /
• v.52 no.6
• /
• pp.412-419
• /
• 2022

Objective: This study evaluated the effect of cyclic pre-calcification treatment on the improvement of bioactivity and osseointegration of Ti-6Al-4V mini-screws. Methods: The experimental groups were: an untreated group (UT), an anodized and heat-treated group (AH), and an anodized treatment followed by cyclic pre-calcification treatment group (ASPH). A bioactive material with calcium phosphate was coated on the mini-screws, and its effects on bioactivity and osseointegration were evaluated in in vitro and in vivo tests of following implantation in the rat tibia. Results: As a result of immersing the ASPH group in simulated body fluid for 2 days, protrusions appearing in the initial stage of hydroxyapatite precipitation were observed. On the 3rd day, the protrusions became denser, other protrusions overlapped and grew on it, and the calcium and phosphorus concentrations increased. The removal torque values increased significantly in the following order: UT group (2.08 ± 0.67 N·cm), AH group (4.10 ± 0.72 N·cm), and ASPH group (6.58 ± 0.66 N·cm) with the ASPH group showing the highest value (p < 0.05). In the ASPH group, new bone was observed that was connected to the threads, and it was confirmed that a bony bridge connected to the adjacent bone was formed. Conclusions: In conclusion, it was found that the surface treatment method used in the ASPH group improved the bioactivity and osseointegration of Ti-6Al-4V orthodontic mini-screws.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.961-965
• /
• 1998

The rapid development of small-scale (1-10 MJ) Superconducting Magnetic Energy Storage Systems (SMES) can be explained by real perspective of practical implementation of these devices in electro power nets. However the serious problem of all high mechanically stressed superconducting coils-problem of training and degradation (decreasing) of operating current still exists. Moreover for SMES systems this problems is more dangerous because of pulsed origin of mechanical stresses-one of the major sources of local heat disturbances in superconducting coils. We investigated acoustic emission (AE) phenomenon on model and 0.5 MJ SMES coils taking into account close correlation of AE and local heat disturbances. Two-coils 0.5 MJ SMES system was developed, manufactured and tested at Russian Research Center in the frames of cooperation with Korean Electrical Engineering Company (KEPCO) [1]. The two-coil SMES operates with the stored energy transmitted between coils in the course of a single cycle with 2 seconds energy transfer time. Maximum operating current 1.55 kA corresponds to 0.5 MF in each coil. The Nb-Ti-based conductor was designed and used for SMES manufacturing. It represents transposed cable made of Nb-Ti strands in copper matrix, several cooper strands and several stainless steel strands. The coils are wound onto fiberglass cylindrical bobbins. To make AE event information more useful a real time instrumentation system was used. Two main measured and computer processed AE parameters were considered: the energy of AE events (E) and the accumulated energy of AE events (E ). Influence of current value in 0.5 MJ coils on E and E was studied. The sensors were installed onto the bobbin and the external surface of magnets. Three levels of initial current were examined: 600A, 1000A, 2450 A. An extraordinary strong dependence of the current level on E and E was observed. The specific features of AE from model coils, operated in sinusoidal vibration current changing mode were investigated. Three current frequency modes were examined: 0.012 Hz, 0.03 Hz and 0.12 Hz. In all modes maximum amplitude 1200 A was realized.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.11
• /
• pp.59-66
• /
• 2007

In order to clarify the influence of gravel content on the mechanical properties of gravel-mixed decompose granite soils, large-scale one-dimensional compression tests were performed. The sample used in the study was a decomposed granite soil from Shimonoseki in Yamaguchi prefecture in Japan. After adjusting the grain size of the said soils, the specimen compacted with a certain level of compaction energy was put to the test. Based on the results obtained, when gravel-mixed decomposed granite soil was compacted at the same energy level, there existed the specific gravel content at which dry density was maximum and which also produced the minimum compression index. Furthermore, from these results, an expression based on a two-phase mixture theory was proposed to quantitatively evaluate the effects of gravel content and initial dry density and the material parameters calculated through the proposed method proved to exactly estimate the actual measuring value.

• Journal of Dairy Science and Biotechnology
• /
• v.41 no.3
• /
• pp.103-112
• /
• 2023

This study aimed to assess the effectiveness of 10 different pre-enrichment methods using Real-Time polymerase chain reaction (PCR) in support of the FDA method. When the initial Cronobacter spp. (Enterobacter sakazakii) inoculation was 7.2 CFU/g, the Ct values were observed in the following order: 21.37 (Enterobacteriaceae enrichment [EE] broth), 21.95 (brain heart infusion [BHI]), 22.72 (tryptic soy broth [TSB]), 23.02 (violet red bile lactose [VRBL]), 22.31 (TSB-0.1% sodium pyruvate [SP]), 23.43 (distilled water [DW]), 24.34 (phosphate buffered saline [PBS]), 24.95 (nutrient broth [NB]), 25.82 (TSB-0.6% yeast extract [YE]), and 28.27 (violet red bile glucose [VRBG]). For an inoculation of 1.82% CFU/g of Cronobacter spp. (E. sakazakii), the Ct values were recorded in this sequence: 20.34 (EE broth), 22.16 (TSB-0.6% YE), 22.37 (BHI), 22.71 (VRBL), 22.88 (TSB), 23.01 (DW), 23.19 (NB), 23.79 (TSB-0.1% SP), 24.66 (VRBG), and 24.70 (PBS). Finally, when the inoculum of Cronobacter spp. (E. sakazakii) was 0.182 CFU/g, the Ct values followed this order: 21.93 (VRBL), 23.07 (TSB-0.6% YE), 23.31 (DW), 23.47 (PBS), 23.70 (BHI), 24.14 (TSB-0.1% SP), 25.14 (TSB), 29.00 (VRBG), 31.55 (EE broth), and were undetected in the case of NB. Consequently, these results indicate that there were no significant differences among the 10 different pre-enrichment broths. Future studies should focus on exploring pre-enrichment broths that can improve the limit of detection at very low Cronobacter spp. (E. sakazakii) concentrations and enhance the selective recovery of Cronobacter spp. (E. sakazakii) under acid, antibiotic, cold, and heat damage conditions.

• Journal of radiological science and technology
• /
• v.31 no.1
• /
• pp.11-16
• /
• 2008

Purpose : The aim of this study was to predict radiation dose at 1 meter with BMI(body mass index) in thyroid cancer patients treated with radio-iodine and provide the efficient guideline in the management of patients. Methods : 140 patients from thyroidectomy for thyroid cancer were enrolled. All subjects under went 150 mCi radio-iodine therapy and performed whole body scan 1 week later. BMI(weight divided by square of height) was calculated to evaluate the amount of fatty tissue indirectly. The radiation dose at 1 meter was measured initially and on 2nd days. the relation of values with BMI were analyzed statically. As for the method of statistical analysis, using Med calc Version 9,2,2,0 Program. Results : (1) The initial effective dose was inversely correlated with the BMI. Significance level was 0.0004. (2) We obtained the following formula from the data of initial effective dose and BMI: Y = -30.91X + 350.4(${\mu}Sv/h$)(Y: initial radiation dose, x: Group). (3) After 21.55 hours, than radiation dose was less than those recommended by ICRP or NRC in 53% of the population. Conclusion : Using BMI, the initial radiation dose and 2nd days dose can be predicted in thyroid cancer patients before radio-iodine therapy. It may be used for predicting the time of discharge and control the isolation room. We were able to predict the radiation exposure after discharge using this calculated value.

• Clinical and Experimental Pediatrics
• /
• v.50 no.10
• /
• pp.1005-1010
• /
• 2007

Purpose : To determine the optimal time of high dose intravenous immune globulin (IVIG) treatment, we analysed the clinical characteristics and progress of a group of Kawasaki disease patients who had early treatment with IVIG. Method : A retrospective study was conducted of 188 patients with Kawasaki disease who were admitted to Yeungnam University Medical Center from January 2000 to December 2005. All patients were treated with a high dose IVIG and high dose aspirin for the initial acute phase treatment. The early treatment group consisted of 94 patients who received treatment before 5 days of fever, and the conventional group consisted of 94 patients who were treated on or after day 5. The patients' sex, age, laboratory findings, total duration of fever, duration of fever after initial IVIG, need for additional IVIG and coronary artery status were noted. Result : There were no significant differences between the two groups in sex ratio and age. No significant differences were noted in the level of WBC count, ESR, CRP, serum albumin, LDH, total duration of fever and coronary abnormality. But the value of ALT($151.8{\pm}17.3$ vs. $81.9{\pm}13.4$, P=0.002), duration of fever after initial IVIG ($3.8{\pm}0.5days$ vs. $2.1{\pm}0.2days$, P=0.003), and rate of additional IVIG (15.9% vs. 6.3%, P=0.037) were significantly higher in the early treatment group. There was no significant difference in initial dose of IVIG, but dosage of aspirin was lower in early treatment group (P=0.037). Conclusion : There is no evidence that early treatment of IVIG has greater efficacy in preventing cardiac sequelae than conventional treatment. In addition, early treatment is likely to result in a greater requirement for additional IVIG treatment.