• Journal of the Korean Ceramic Society
• /
• v.44 no.1 s.296
• /
• pp.43-51
• /
• 2007

Fluidity, setting time, hydration heat, bond water ratio, compressive strength, SEM and BET of OPC were measured by adding 1.0 wt% KCl and replacing 20 wt% mineral admixture in order to examine effects of blast furnace slag (BFS), limestone powder (LSP), and fly ash (FA) on fluidity and strength development of the cement contained much chloride. In general, the cement contained much chloride was high in heat of hydration, short in its setting time, low in its fluidity and low in its strength at 28 days due to the rapid hydration in its initial stage. As a result of the experiment, it has been demonstrated that fluidity became improved but the compressive strength at 28 days was decreased as replaced LSP to the cement contained much chloride. the fluidity and compressive strength at 28 days was improved as replaced BFS, the initial compressive strength development was improved due to the activation of initial reaction by KCl. Fluidity, initial compressive strength and late compressive strength at 28 days of cement contained much chloride replaced 5 wt% LSP and 15 wt% BFS concurrently was better than OPC, but the hydration heat was lower.

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.57-67
• /
• 2002

The effect of $\beta$-TCP and PHA as additives on initial setting time, compressive strength and surface micro-structure after in vitro test of bone cement in TTCP and DCPA system was investigated. The median particle sizes of TTCP, $\beta$-TCP, DCPA and PHA for bone cement were about 3, 5, 0.9 and 4${\mu}{\textrm}{m}$, respectively. Initial setting time and compressive strength of bone cement with various composition was measured by Vicat test and Universal Testing Machine, and surface morphology and crystalline phases of bone cements were observed and analyzed by SEM and x-ray diffractometer. Initial setting time was not affected by composition but by powder/liquid ratio, and cement with PHA required double amount of solution for paste as much as one without PHA, especially. It was thought that $\beta$-TCP and PHA in bone cements was not related to setting reaction. Thus, the addition of $\beta$-TCP and PHA in bone cements decreased compressive strength and inhabited HAP from being produced on surface in vitro test. In conclusion, it was not expected that $\beta$-TCP and PHA in TTCP-DCPD bone cements enhanced the strength and bioacitivity.

• Computers and Concrete
• /
• v.3 no.2_3
• /
• pp.177-195
• /
• 2006

Slipforming is a construction method in which the forms move continuously during the placement of concrete. This paper presents the development of a computer aided program designated as "CADSLIPFORM" for slipforming operations. The program incorporates maturity methods for the prediction of initial setting times of slipform concrete layers using laboratory data (time-temperature histories and setting times of concrete mixtures at different temperatures) and generates slipform mock-up times. The performance of CADSLIPFORM is validated by comparing simulated mock-up times with those estimated in the field through conventional hard front by rod (R) method. Moreover, the program versatility is demonstrated by illustrating mock-up simulations for different cases with variable slipform parameters such as: number and thickness of concrete layers, concrete temperature (simulating variable setting times) and slipform speed. The program also incorporates the choice of Freiesleben Hansen & Pederson (FHP) and Carino & Tank (CT) maturity functions. CADSLIPFORM can assist user to develop reliable schedule of slipforming operation suitable for a specific project by optimizing various slipform parameters.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.4
• /
• pp.48-56
• /
• 2022

Controlling the setting time of cementitious materials is one of the most important factors in securing early-age performance of concrete structures. Recently, the use of retarding admixtures, which enable the inhibition of some hydration products to control the securing time due to average temperature rise is suggested. Although various non-destructive evaluation methods have been proposed to evaluate cement hydration and hardening of cement-based materials to overcome the limitations of Vicat needle test, experimental research is still required to use the non-destructive evaluation method with added retarding admixtures. In this study, measurements of electrical resistivity and ultrasonic wave velocity in early-aged cement pastes were performed according to the addition of retarding admixture(tartaric acid). The setting time of the cement pastes was evaluated by obtained rising time of the both non-destructive measurements. As a result, the possibility of evaluating the setting delay in cement pastes was confirmed through comparative analysis with the initial and final setting times by Vicat test. In addition, X-ray diffraction results at the rising time of electrical resistivity showed a key hydration product affecting the setting delay.

• Restorative Dentistry and Endodontics
• /
• v.25 no.1
• /
• pp.123-132
• /
• 2000

To overcome problems of conventional glass ionomers, resin components have been added to glass ionomers. On a continuum between glass ionomers and composites are a variety of blends, employing different proportions of acid-base and free radical reactions to bring about cure. Popular groups defined between the ends are resin-modified glass-ionomers(RMGIs), polyacid-modified composite resins(Compomers) and ionomer modified resins. These groups show different clinical properties, and in selecting these materials for a restoration, one should sufficiently understand these different setting properties. In this study, some difference in the setting characteristics of different groups of hybrid ionomers were examined. Two RMGIs (Fuji2 LC,GC / Vitremer, 3M), three Compomers (Dyract AP, Dentsply / F2000, 3M / Elan, Kerr) were involved in this study. The identification of the setting characteristics of different groups was achieved by a two-stage study. First, thermal analysis was performed by a differential scanning calorimeter, and then the hardness of each group at different depth and time were measured by a micro-hardness tester. Thermal analysis was performed to identify the inorganic filler content and to record the heat change during setting process. The setting process was progressed for each material by chemical set mode and light-cured mode. In the hardness test, samples of materials were prepared with a 6mm-diameter metal ring, and the hardness was measured at the top, and 1mm, 2.5mm, 4mm below at just after a 40 second-cure, and after 10 minutes, 24 hours, and 7 days. Statistical analysis was performed by Mann-Whitney rank sum test to assess significant differences between set modes and types of materials, and by ANOVA and T-test to evaluate the statistical meanings of data at different times and depths of each materials. Followings are findings and conclusions derived from this study. Thermal analysis; 1. Compomers show no evidence of chemical setting while RMGIs exhibit heat output during the process of chemical setting. 2. Heat of cure of RMGIs exceed Compomers. 3. The net heat output of RMGIs through light-cured mode is higher than through chemically set mode. Hardness test; 1. Initial hardness of RMGIs immediately after light cure is relatively low, but the hardness increases as time goes by. On the contrary, Comomers do not show evident increase of the hardness following time. 2. Compomers show a marked decrease of setting degree as the depth of the material increases. In RMGIs, the setting degree at different depths does not significantly differ.

• Journal of the Korea Concrete Institute
• /
• v.12 no.3
• /
• pp.3-10
• /
• 2000

In this study, we compared a plain mortar with the CAS-system shrinkage compensation mortar for Ondol that is Korean traditional heating system. The Ondol mortar is necessary to have properties as non-crack, fine flatness and stability for thermal changes. especially, mortar'crack prevention is to be most important property in Ondol mortar. To develope the stable material on the crack-prevention, we used to calcium-sulfo-aluminate(CSA)system in shrinkage compensation mortar. And so, we confirmed the effects of calcium-sulfo-aluminate(CSA) system for mortar's physical properties such as setting time, compressive strength and expansion ratio for crack prevention. The initial and final setting time of the CSA mortar is faster than plain mortar about 2hours. And, Compressive strength increased about 20% that plain mortar. The crack length per unit area, plain mortar is 0.426∼0.481m/m2. The Results of apartment construction field test, the shrinkage compensation mortar is excellent about the crack-reduce effect.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.116-117
• /
• 2019

In this research, Proctor insertion resistance test values and Durometer A type hardness values were compared and analyzed between the setting times of the concrete using CGS for Fine Aggregate, and the results are summarized as follows. 1) The Proctor penetration resistance test value and the hardness value of Durometer A type showed a high correlation in the form of a curve. 2) About surface finish The resolution exceeding the hardness value of the Durometer A type uses about 25 HD, and in the case of termination, about 35 HD, and is considered to be effective for determining the surface finishing work time. The possibility to do is expected.

• Journal of the Korea Concrete Institute
• /
• v.29 no.2
• /
• pp.141-148
• /
• 2017

This study is experimentally investigated the effects of various steam curing parameters on the early-age compressive strength development of high strength concrete (over 40 MPa) in the precast plant production. High strength concrete are used only ordinary portland cement (type I) and water-cement ratio selected 3cases (25%, 35% and 45%). Also, steam curing parameters are as followings ; (1) Preset period 2cases (3 hours and 6 hours) (2) Maximum curing temperature 3cases ($45^{\circ}C$, $55^{\circ}C$ and $65^{\circ}C$) (3) Maintenance time of curing temperature 3cases (4 hours, 6 hours and 8 hours) (4) Maximum rate of heating and cooling $15^{\circ}C$/hr. Initial setting time and adiabatic temperature rising ratio of these concrete according to water-cement ratio are tested before main tests and examined the compressive strength development for the steam curing parameters. Also compressive strength are compared with optimum steam curing condition and standard curing at test ages. As test results, the optimum steam curing conditions for high strength concrete(over 40 MPa) are as followings. (1) Preset period ; over initial setting time of concrete (2) Maximum curing temperature ; bellow $55^{\circ}C$ (3) Maintenance time of curing temperature ; bellow 6hours. Also strength development of steam curing concrete show in the reversed strength at 28 days. It is to propose an efficient steam curing condition for high strength concrete in the precast method.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.62 no.2
• /
• pp.31-38
• /
• 2020

Controlled Low Strength Material (CLSM) has high fluidity and self-compaction characteristics. CLSM is mainly used for backfilling the excavated road. Early-age properties of CLSM should be characterized for fast restoration of the road. In this study, shear wave monitoring and Vicat needle test are performed to investigate the early-age properties of CLSM depending on the setting time. CLSM consists of CSA cement, fly ash, silt and sand, accelerator, and water. Five fly ashes with different chemical properties are used for CLSM samples. The penetration of CLSM along setting time is obtained through the Vicat needle test. A pair of bender elements are placed in a mold for shear wave measurement, and the change in shear waves with the setting time is monitored. The experimental results show that, regardless of the type of fly ash, the penetration depth decreases and the shear wave velocity increases with the setting time. Depending on the type of fly ash, initial and final times and shear wave velocity change. After testing, the correlation between penetration and shear wave velocity is obtained with high coefficient of determination. The shear wave measurement technique using the bender element can be used to identify early-age properties.

• Journal of the Korea Concrete Institute
• /
• v.23 no.3
• /
• pp.347-352
• /
• 2011

When concrete is worked in cold weather, the methods of using hot air, water and aggregate heating, accelerators are used to prevent early frosting and to improve early strength. But these methods raise problems such as implementation difficulty, high cost, and energy losses. Among the available cold weathering methods, accelerator method is the most economical but with the drawbacks of rapid setting and insufficient workability in the initial hydration stage. Therefore, the tablet method usually used for pharmaceutical field was applied to the accelerator method to compare the controlled reaction time of the new and old accelerator method. Based on the test results, physical and mechanical properties of concrete were tested and the possibility of delaying initial reactions to increase the total reaction time was evaluated. The results showed that when both accelerators and tablet were used, setting-time decreased. Physical properties of concrete were optimal for tablet 0.5% and 1.0%. Also, accelerator 0.5%, tablet 0.5% and 1.0% showed good early strengths.