• ETRI Journal
• /
• v.42 no.1
• /
• pp.46-53
• /
• 2020

Gait analysis is an effective clinical tool across a wide range of applications. Recently, inertial measurement units have been extensively utilized for gait analysis. Effective gait analyses require good estimates of heel-strike and toe-off events. Previous studies have focused on the effective device position and type of triaxis direction to detect gait events. This study proposes an effective heel-strike and toe-off detection algorithm using a smart insole with inertial measurement units. This method detects heel-strike and toe-off events through a time-frequency analysis by limiting the range. To assess its performance, gait data for seven healthy male subjects during walking and running were acquired. The proposed heel-strike and toe-off detection algorithm yielded the largest error of 0.03 seconds for running toe-off events, and an average of 0-0.01 seconds for other gait tests. Novel gait analyses could be conducted without suffering from space limitations because gait parameters such as the cadence, stance phase time, swing phase time, single-support time, and double-support time can all be estimated using the proposed heel-strike and toe-off detection algorithm.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1001-1006
• /
• 2003

This paper presents the pedestrian navigation algorithm and the error compensation filter. The pedestrian navigation system (PNS) consists of the MEMS inertial sensors, the fluxgate, and the small-size GPS receiver. PNS calculates the navigational information using the signal patterns of the accelerometers. And the navigational information is completed by integration of the patterns, the fluxgate, and the GPS information. In general, PNS can provide the better solution than the low-cost inertial navigation system.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.3
• /
• pp.173-182
• /
• 2015

A real-time, Indoor navigation systems utilize ultra-wide band (UWB), radio-frequency identification (RFID) and received signal strength (RSS) techniques that encompass WiFi, FM, mobile communications, and other similar technologies. These systems typically require surplus infrastructure for their implementation, which results in significantly increased costs and complexity. Therefore, as a solution to reduce the level of cost and complexity, an inertial measurement unit (IMU) and quick response (QR) codes are utilized in this paper to facilitate navigation with the assistance of a smartphone. The QR code helps to compensate for errors caused by the pedestrian dead reckoning (PDR) algorithm, thereby providing more accurate localization. The proposed algorithm having IMU in conjunction with QR code shows an accuracy of 0.64 m which is higher than existing indoor navigation techniques.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1429-1432
• /
• 2005

This work is towards the development of a low-cost, small-sized inertial navigation system(INS) which consists of 3 accelerometers, 3 semiconductor gyros and a magnetic compass sensor. This paper explains in detail the structure of the developed system and proposes a 3 dimensional attitude estimation algorithm with Indirect Kalman Filter. The experiments are performed with the developed system attached to a 6 DOF robot for showing the effectiveness of the algorithm.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.12
• /
• pp.1120-1125
• /
• 2000

This paper presents a technique for estimating the attitude of a model helicopter at near hovering using a combination of inertial and non-inertial sensors such as gyroscope and potentiometer. To estimate the attitude of helicopter a simplified indirect Kalman filter based on sensor modeling is derived and the characteristics of sensors are studied, which are used in determining the optimal Kalman gain. To verify the effectiveness of the proposed algorithm simulation results are presented with real flight data. Our approach avoids a complex dynamic modeling of helicopter and allows for an elegant combination of various sensor data with different measurement frequencies. We also describe the method of implementation of the algorithm in the model helicopter.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.2
• /
• pp.155-160
• /
• 2007

A fault detection and isolation (FDI) problem is considered for inertial sensors, such as gyroscopes and accelerometers and a new FDI method for double faults is proposed using reduced-order parity vector. The reduced-order parity vector (RPV) algorithm enables us to isolate double faults with 7 sensors. Averaged parity vector is used to reduce false alarm and wrong isolation, and to improve correct isolation. The RPV algorithm is analyzed by Monte-Carlo simulation and the performance is given through fault detection probability, correct isolation probability, and wrong isolation probability.

• ETRI Journal
• /
• v.43 no.4
• /
• pp.594-602
• /
• 2021

Recently, quantitative and repetitive inspections of the old urban area were conducted because many structures exceed their designed lifetime. The health of a building can be validated from the condition of the outer wall, while the slant angle of the wall widely serves as an indicator of urban regeneration projects. Mostly, the inspector directly measures the inclination of the wall or partially uses 3D point measurements using a static light detection and ranging (LiDAR). These approaches are costly, time-consuming, and only limited space can be measured. Therefore, we propose a mobile mapping system and automatic slant map generation algorithm, configured to capture urban environments online. Additionally, we use the LiDAR-inertial mapping algorithm to construct raw point clouds with gravity information. The proposed method extracts walls from raw point clouds and measures the slant angle of walls accurately. The generated slant angle map is evaluated in indoor and outdoor environments, and the accuracy is compared with real tiltmeter measurements.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.175-185
• /
• 2011

Geometric information is a key element for evaluating traffic safety and road maintenance. This study developed an algorithm to identify horizontal alignment using global positioning system(GPS) and inertial navigation system(INS) data. Roll and heading information extracted from GPS/INS were utilized to classify horizontal alignment into tangent, circular curve, and transition curve. The proposed algorithm consists of two components including smoothing for eliminating outlier and a heuristic classification algorithm. A genetic algorithm(GA) was adopted to calibrate parameters associated with the algorithm. Both freeway and rural highway data were used to evaluate the performance of the proposed algorithm. Promising results, which 90.48% and 88.24% of classification accuracy were obtainable for freeway and rural highway respectively, demonstrated the technical feasibility of the algorithm for the implementation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.6
• /
• pp.463-472
• /
• 2017

Inertial Navigation System Alignment is the process to determine direction cosine matrix which is the transformation matrix between the INS body frame and navigation frame. INS initial position value is necessary to INS attitude calculation, so that user should wait until he get such value to start the INS alignment. To remove the waiting time, we propose an alignment algorithm that immediately starts after the INS power on by using pseudo initial position input and then is completed with attitude error compensation by entering true position later. We analyse effect of INS sensor error on attitude in process of time and verify the performance and usefulness of the close-loop alignment algorithm which corrects attitude error from the change of initial position.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.6
• /
• pp.82-90
• /
• 2011

This paper proposes an advanced outdoor localization algorithm of a GPS(global positioning system)-INS(inertial navigation system) integration system. In order to reduce noise from the internal INS sensors, discrete wavelet transform and variable threshold method are utilized. The UPF (unscented particle filter) combines GPS information and INS signals to implement precise outdoor localization algorithm and to reduce noise caused by the acceleration, deceleration, and unexpected slips. The conventional de-noising method is mainly carried out using a low pass filter and a high pass filter which essentially result in signal distortions. This newly proposed system utilizes the vibration information of actuator according to fluctuations of the velocity to minimize signal distortions. The UPF also resolves non-linearities of the actuator and non-normal distributions of noises. Effectiveness of the proposed algorithm has been verified through the real experiments and the results are demonstrated.