• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.20 no.1
• /
• pp.33-41
• /
• 2022

Liquid Bi pool is a candidate electrode for an electrometallurgical process in the molten LiCl-KCl eutectic to treat the spent nuclear fuels from nuclear power plants. The electrochemical behavior of Bi³⁺ ions and the electrode reaction on liquid Bi pool were investigated with the cyclic voltammetry in an environment with or without BiCl₃ in the molten LiCl-KCl eutectic. Experimental results showed that two redox reactions of Bi³⁺ on inert W electrode and the shift of cathodic peak potentials of Li⁺ and Bi³⁺ on liquid Bi pool electrode in molten LiCl-KCl eutectic. It is confirmed that the redox reaction of lithium with respect to the liquid Bi pool electrode would occur in a wide range of potentials in molten LiCl-KCl eutectic. The obtained data will be used to design the electrometallurgical process for treating actinide and lanthanide from the spent nuclear fuels and to understand the electrochemical reactions of actinide and lanthanide at liquid Bi pool electrode in the molten LiCl-KCl eutectic.

• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.42-47
• /
• 2024

The electrochemical extraction of uranium in ternary low melting LiCl-KCl-CsCl eutectic on inert and reactive electrodes via different electrochemical techniques was investigated. It was established that the electrochemical reduction process of U(III) ions on the inert W electrode was irreversible and proceeded in one stage. On reactive liquid Ga and liquid Cd electrodes the reduction of uranium ions took place with the considerable depolarization with the formation of UGa₂, UGa₃ and UCd₁₁ intermetallic compounds. Thermodynamic characteristics of uranium compounds and alloys were calculated. The conditions for the extraction of uranium from the electrolyte in the form of alloys on both liquid reactive electrodes via potentiostatic electrolysis were found.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.3
• /
• pp.279-285
• /
• 2012

It is necessary to install the inert gas system(IGS) for preventing fire and explosion in LNGC main diesel engine crankcase besides oil mist detector(OMD) unit with $CO_2$ gas injector. Therefore, to design the liquid nitrogen IGS, analytical work is conducted for predicting the heat input load of liquid nitrogen heater with two-phase stratified flow model. This paper also presents the effects of changes in pipe diameter, saturated pressure, and inclination angle by ship's movement on cryogenic two-phase stratified flows. It is found that the stratified model gives reasonable predictions, and the model is effective to predict the heat input load of liquid nitrogen IGS.

• Journal of Information Display
• /
• v.13 no.1
• /
• pp.37-42
• /
• 2012

An empirical functional form was suggested for the analysis of the emission spectrum of high-power light-emitting diode (LED) consisting of a sharp blue peak from the LED chips and a broad yellow peak from the phosphor layer. The peak positions, half widths, shape parameters, and amplitudes of these two peaks were reliably obtained as a function of the temperature, and the results were discussed qualitatively in relation with the junction temperature. The adoption of an inert liquid was found to have significantly reduced the LED temperature and the color shift of the emitted light. The phenomenological approach used in this study may be helpful in the simulation of the LED spectrum under various thermal conditions, and may thus be helpful in the improvement of the device performance.

• Journal of Mechanical Science and Technology
• /
• v.14 no.4
• /
• pp.466-476
• /
• 2000

This paper presents atomization characteristics of a double impinging F -0-0- F type injector with four streams. A phase Doppler particle analyzer was employed to measure the droplet-size and water was used as the inert simulant liquid instead of reactive propellant liquids. The droplet mean diameter (SMD) and size distribution were measured to investigate the effects of the momentum ratio and pressure drop variations. This experimental results can be used during the preliminary design stage of a impinging stream type injector for liquid rockets.

• Nuclear Engineering and Technology
• /
• v.50 no.6
• /
• pp.849-853
• /
• 2018

Mechanistic calculations for wet scrubbing of aerosol/vapor from gas bubble rising in liquid pool are essential to safety of sodium-cooled fast reactor. Hence, scrubbing of volatile fission product from mixed gas bubble rising in sodium pool is presented in this study. To understand this phenomenon, a theoretical model has been setup based on classical theories of aerosol/vapor removal from bubble rising through liquid pools. The model simulates pool scrubbing of sodium iodide aerosol and cesium vapor from a rising mixed gas bubble containing xenon as the inert species. The scrubbing of aerosol and vapor are modeled based on deposition mechanisms and Fick's law of diffusion, respectively. Studies were performed to determine the effect of various key parameters on wet scrubbing. It is observed that for higher vapor diffusion coefficient in gas bubble, the scrubbing efficiency is higher. For aerosols, the cut-off size above which the scrubbing efficiency becomes significant was also determined. The study evaluates the retention capability of liquid sodium used in sodium-cooled fast reactor for its safe operation.

• Journal of ILASS-Korea
• /
• v.23 no.4
• /
• pp.159-168
• /
• 2018

Thrust throttling in a liquid rocket engine can be implemented via several ways such as high pressure drop injector, dual manifold, multiple chamber, pintle injector, and gas injection. Thrust throttling using gas injection controls thrust by usually injecting inert gas into propellant through an aerator to reduce the propellant's bulk density. In this study, the outside-in aerator was used in the propellant line to create two phase flow. Closed-type, open-type, and screw-type bi-swirl coaxial injectors were utilized for investigating throttling characteristics such as pressure drop, mixture density, and discharge coefficient according to gas-liquid mass ratio.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.10
• /
• pp.1-7
• /
• 2020

In this study, a multichannel gas-liquid microextraction system is designed by integrating the automatic elution of extraction line and multichannel gas-purging liquid phase microextraction. The system uses an injection pump and inert gas to push the extraction solvent to a sample bottle of a gas-phase color autosampler and then implements multichannel gas-liquid microextraction and gas chromatography-mass spectrometry. The system also employs a three-way integrated micro-high-temperature heater, syringe pump, and microflow controller to realize the simultaneous processing of multiple groups of samples, thus improving the sample pretreatment speed and reproducibility and reducing human error. Autoinjection experiments were implemented with polycyclic aromatic hydrocarbon standard samples. The experiments show that the average recovery rate of the system exceeds 70%, and the relative standard among the channels is less than 15%.

• Natural Product Sciences
• /
• v.6 no.1
• /
• pp.20-24
• /
• 2000

The enantiomers of higenamine were directly separated by high performance liquid chromatography using a chiral stationary phase and detected by UV. The R- and S-isomers of higenamine were eluted at the retention time of 22 min and 27 min, respectively. Higenamine was determined to be present as R-(+)-enantiomer not only in the embryo of Nelumbo nucifera, from which the separation of R-(+)-higenamine was reported, but also in various Aconite roots, from which higenamine was separated as optically inert racemic mixtures.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1409-1411
• /
• 2006

A new rod-like liquid crystalline monomer having divinyl terminal groups was synthesized and polymerized by using thiol-ene UV polymerization technique. High quality thin film with good retardation value was prepared on a rubbed alignment layer without the inert gas purging. The retardation value of the resulting film was controlled by experimental conditions such as spin speed, concentration, and spin time. From the retardation value and thickness measurement, ${\bigtriangleup}n$ was calculated to be 0.169 for the resulting film having thickness of 815.1 nm.