• Journal of Advanced Marine Engineering and Technology
• /
• 제28권4호
• /
• pp.632-640
• /
• 2004

The purpose of this study is to clarify the influence of inert gas on the configuration characteristics of premixed turbulent propagating flames of hydrogen mixtures. Inert gas is changed to $N_2$, Ar, $CO_2$ and He keeping the laminar burning velocity of mixtures nearly the same value. A laser tomography technique was used to obtain the flame shape, and quantitative analyses were performed. The result shows that in the wrinkled laminar flame region, the surface area of turbulent flame is slightly dependent on the equivalence ratio and the kind of inert gas. It is also shown the region of convex part of flame toward the unburned gas is greater than that of toward the burned gas regardless of the kind of inert gas.

• 연구논문집
• /
• 통권29호
• /
• pp.5-15
• /
• 1999

Present study deals with performance analysis of an inert gas generator (IGG) which is to be used as an effective mean to suppress the fire. The IGG uses a turbo jet cycle gas turbine engine to generate inert gas for fire extinguishing. It is generally known that a lesser degree of oxygen content in the product of combustion will increase the effectiveness of fire suppressing. An inert gas generator system with water injection will bring advantages of suffocating and cooling effects which are considered as vital factors for fire extinguishing. As the inert gas is injected to the burning site, it lowers the oxygen content of the air surrounding the flame as well as reduces the temperature around the fire as the vapour in the inert gas evaporates during the time of spreading. Some important aspects of influencing parameters, such as, air excess coefficient. $\alpha$, compressor pressure ratio, $ pi_c$, air temperature before combustion chamber, $T_2$, gas temperature after combustion chamber, $T_3$, mass flow rate of water injection, $M_w$, etc., on the performance of IGG system are investigated. Calculations of total amount of water needed to reduce the turbine exit temperature to pre-set nozzle exit temperature employing a heat exchanger were made to compare the economics of the system. A heat exchanger with two step cooling by water and steam is considered to be better than water cooling only. Computer programs were developed to perform the cycle analysis of the IGG system and heat exchanger considered in the present study.

• Journal of Welding and Joining
• /
• 제5권2호
• /
• pp.17-26
• /
• 1987

In this study, the experiments were carried out for the purpose of establishment of the arc sparing method which reducing oxides or oxide film by using the inert gas as the carrier gas of atomizing particles. Main results obtained are as follows; 1. Oxides and oxide film which lower the adhesion strength are largely reduced by using the inert gas as the carrier gas of atomizing particles, and adhesion strength of coating film are improved. 2. The coating film characteristics appear to be no difference between the inert gas arc spraying in air environment and that in argon gas environment. 3. Inert gas arc spraying using argon as the carrie gas has higher reduction rate of composition element in coating film than compressed air spraying does.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.589-596
• /
• 2008

Performance of a pulsed heat source high temperature inert gas plasma MHD electrical power generator, which can be one of the candidates of space-based laser-to-electrical power converter, is examined by a time dependent two dimensional numerical simulation. In the present MHD generator, the inert gas is assumed to be ideally heated to about $10^4K$ pulsed-likely within short time(${\sim}1{\mu}s$) in a stagnant energy input volume, and the energy of high temperature inert gas is converted to the electricity with the medium of pure inert gas plasma without seeding. The numerical simulation results show that an enthalpy extraction ratio(=electrical output energy/pulsed heat energy) of several tens of % can be achieved, which is the same level as the conventional seeded non-equilibrium plasma MHD generator. Although there still exist many phenomena to be clarified and many problems to be overcome in order to realize the system, the pulsed heat source high temperature inert gas MHD generator is surely worth examining in more detail.

• 한국화재소방학회논문지
• /
• 제19권2호
• /
• pp.69-74
• /
• 2005

대량의 비활성가스를 발생시키는 Inert Gas Generator(IGG)를 소화설비로 사용하기 위해 본 연구에서는 가스터빈을 채용한 IGG에서 발생되는 배기가스의 소화성능을 검토하였다. IGG에서 발생하는 가스는 조성을 동일하게 만든 모사 혼합가스를 이용하였으며, Cup Burner시험방법으로 소화농도를 측정하였다. 얻어진 소화농도를 NFPA 2001에서 권장하는 방법에 적용하여 소화설계 농도 및 소화공간 크기를 산정하였다. 또한, $2m\times2m\times2m$ 크기의 공간에서 화재진압 실험을 수행하여 실제 소화성능을 확인하였다.

• 한국안전학회지
• /
• 제23권6호
• /
• pp.95-99
• /
• 2008

Halon was known as a cause of the ozone layer destruction. In 1987, it was designated as one of the ozone-layer-destroying materials in the Montreal Protocol. Therefore substitutes of Halon agent has been developed including inert gas extinguish system, which is one of the most widely used fire extinguishing system. This study intended to increase the efficiency of inert gas extinguishing agent by using inert gas additives. As IG-541 shows high extinguishing power, the experiment was performed to measure the effects of gaseous additives to it. Cup-burner fire extinguishing apparatus was used with n-Heptane fuel. Among many of pure inert gaseous agents, Helium showed the most excellent extinguishing power. When Helium was added to IG-541, fire extinguishing power was increased and the concentration of oxygen in chimney also risen. By adding Helium to IG-541, the effectiveness of inert gas fire extinguishing system is able to be increased.

• 한국화재소방학회논문지
• /
• 제16권3호
• /
• pp.77-83
• /
• 2002

질소, 아르곤, 이산화탄소와 같은 불활성가스 및 이들의 혼합물을 소화약제로 하여 n-Heptane을 연료로한 cup-burner test 장치에서 불꽃소화농도와 연소시 배가스의 조성을 측정하였다. 이성분 불활성가스계 혼합소화약제의 소화농도는 혼합물의 구성비를 이용한 모델에 의해 잘 예측됨을 알 수 있었다. 불활성 가스계 혼합 소화약제에 의한 소화작용에 있어서 혼합가스의 평균비중이 클수록 소화 성능이 우수하였다. 또한 밀폐된 공간의 구조가 소화에 영향을 미칠 수 있음을 확인하였다. 연소시 배가스 중 이산화탄소 조성은 사용하는 소화약제의 양이 증가할수록 감소하였다. 일산화질소 발생은 소화약제의 질소 함량과는 상관이 없으며 공기유량을 크게 하여 불꽃을 크게 했을 때 검출되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1651-1656
• /
• 2003

The present study has been conducted to analytically investigate the thermal control performance of variable conductance heat pipe(YCHP) with axial grooves. The condenser port of the YCHP is occupied by a inert gas in which the concentration of gas is varied with the operation temperature and the heat transport capacity is thus varied with the operating temperature due to the variation of inert gas concentration. In this study, numerical evaluation for the thermal control of the YCHP with axial grooves is made from the 1st order diffusion model that considers the diffusive expansion of inert gas by concentration gradient. Ammonia is used as a working fluid and Nitrogen as a control gas in the Aluminum tube. As a result, the thermal performance of YCHP based on diffusion model has been compared with that of YCHP from flat front model. Additionally, it is found that the concentration of inert gas is distributed in the condenser region of YCHP with axial grooves.

• Environmental Engineering Research
• /
• 제24권3호
• /
• pp.521-528
• /
• 2019

Electrochemical method was used for the fracturing flow-back fluid treatment in Guangyuan oilfield. After performing electrolysis, we found that the amount of $H_2$ gas produced by electrode was closely related to the combination mode of electrodes and electrode materials. Using an aluminium electrode resulted in a large $H_2$ production of each electrode combination, whereas inert anode and cathode materials resulted in low $H_2$ production. Then, the relationship between the gas production of $H_2$ and the treatment efficiency of fracturing flow-back fluid in Guangyuan oilfield was studied. Results showed that the turbidity removal and decolourisation rates of fracturing flow-back fluid were high when $H_2$ production was high. If the $H_2$ production of inert electrode was large, the energy consumption of this inert electrode was also high. However, energy consumption when an aluminium anode material was used was lower than that when the inert electrode was used, whereas the corresponding electrode combination production of $H_2$ was larger than that of the inert electrode combination. When the inert electrode was used as anode, the gas production type was mainly $O_2$, and $Cl_2$ was also produced and dissolved in water to form $ClO^-$. $H_2$ production at the cathode was reduced because $ClO^-$ obtained electrons.

• 청정기술
• /
• 제17권3호
• /
• pp.209-214
• /
• 2011

직경 0.15 m, 높이 1.0 m인 매체유동층 건조기 내에서 유입 열풍유속(0.26~0.31 m/s), 유입 열풍온도(315~353 K) 및 미세 고분자입자와 매체입자의 질량비(0.1~0.4)에 따른 미세 고분자의 건조속도에 관한 영향을 조사하였다. 건조에 사용된 미세 고분자는 평균입경이 20 ${\mu}m$인 가교 PMMA beads로써 Geldart group C 입자이고, 매체입자는 Group B인 직경 590 ${\mu}m$인 glass beads를 이용하였다. 건조속도는 유입열풍유속 및 유입열풍온도에 따라 증가하였고, 미세 고분자와 매체입자의 질량비에 따라 감소하였다. 건조된 미세 고분자(PMMA)의 입도분포형태는 단일분포를 나타내었다.