• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.4
• /
• pp.153-157
• /
• 2023

In order to manufacture a semiconductor circuit, etching, cleaning, and deposition processes are repeated. During these processes, the inside of the processing chamber is exposed to corrosive plasma. Therefore, the coating of the inner wall of the semiconductor equipment with a plasma-resistant material has been attempted to minimize the etching of the coating and particle contaminant generation. In this study, we mixed AlF₃ powder with the solid-state reacted yttrium oxyfluoride (YOF) in order to increase plasma-etching resistance of the plasma spray coated YOF layer. Effects of the mixing ratio of AlF₃ with YOF powder on crystal structure, microstructure and chemical composition were investigated using XRD and FE-SEM. The plasma-etching ratios of the plasma-spray coated layers were calculated and correlation with AlF₃ mixing ratio was analyzed.

• Membrane Journal
• /
• v.33 no.4
• /
• pp.191-200
• /
• 2023

Polyethersulfone (PES) is a widely employed membrane material for water and industrial purification applications owing to its hydrophilicity and ease of phase separation. However, PES membranes and filters prepared using the nonsolvent induced phase separation method often encounter significant flux decline due to pore clogging and cake layer formation on the dense membrane surfaces. Our investigation revealed that tight microfiltration or loose ultrafiltration membranes can be subject to physical fouling due to the formation of a dense skin layer on the bottom side caused by water intrusion to the gap between the shrank membrane and the substrate. To investigate the effect of the bottom surface porosity on membrane fouling, two membranes with the same selective layers but different sub-layer structures were prepared using single and double layer casting methods, respectively. The double layered PES membrane with highly porous bottom surface showed high flux and physical fouling tolerance compared to the pristine single layer membrane. This study highlights the importance of physical optimization of the membrane structure to prevent membrane fouling.

• Journal of the Society of Disaster Information
• /
• v.19 no.3
• /
• pp.519-531
• /
• 2023

With the aim of preventing safety accidents at construction sites, the company aims to create safe behaviors intended through variables called smart safety and health activities to help reduce industrial accidents. Purpose: It analyzes how smart safety and health activities affect accidents caused by unsafe behavior and changes in worker behavior, which is the root cause, and verifies the hypothesis that it helps prevent safety accidents and protect workers' lives. Method: Smart safety and health activities were selected as independent variables (X), and intended safety and anxiety, which are workers' behavioral intentions, were set as dependent variables (Y), attitude and subjective norms, and planned behavioral control as parameters (M). Exploratory factor analysis, discriminant validity analysis, and intensive validity analysis of safety and health activities were used to analyze the scale's reliability and validity. To verify the hypothesis of behavior change, the study was verified through Bayesian model analysis and MC simulation's probability density distribution. Result: It was found that workers who experienced smart safety and health activities at construction sites had the highest analysis of reducing unstable behavior and performing intended safety behavior. The research hypothesis that this will affect changes in worker behavior has been proven, the correlation between variables has been verified in the structural equation and path analysis of the research analysis, and it has been confirmed that smart safety and health activities can control and reduce worker instability. Conclusion: Smart safety and health activities are a very important item to prevent accidents and change workers' behavior at construction sites.

• Applied Chemistry for Engineering
• /
• v.34 no.4
• /
• pp.444-449
• /
• 2023

As electronic devices become smaller and more integrated, the demand for manufacturing thin, flexible printed circuit boards (FPCBs) has increased. Although FPCBs are conventionally manufactured by a photolithography method using dry film resist, this process is complicated, and the mask is specifically designed to obtain the precision of the desired circuit line width. In this regard, manufacturing FPCBs with fine patterns through the direct printing method of photocurable inks has gained growing attention. Since the manufacturing process of FPCBs is based on the direct printing method that includes etching and stripping processes utilizing acid and basic chemicals, controlling the adhesion strength, the etching resistance, and the strippability of photocured inks has drawn a lot of attention for the fabrication of fine patterns through photocurable inks. In this study, acrylic ink with various types and contents of the photoinitiator was prepared, and the curing behavior was analyzed. Also, the adhesion strength, etching resistance, and strippability were analyzed to evaluate the applicability of developed photocurable etching resist inks.

• Journal of Korea Entertainment Industry Association
• /
• v.13 no.6
• /
• pp.221-233
• /
• 2019

The purpose of this study tries to show the effectiveness of integrated theater education for low-grade students who lack social skills with the direction of art education based on 'theatrical and educational theater' and 'theater therapy' in the revised curriculum in 2015. To do this, the researcher organized a theater camp organized by the social, cultural and arts education institute in Seoul for a total of 12 low-grade elementary school students for four weeks, and had a presentation session. In addition, the researcher observed the behavioral changes of the participating children to verify the social development of the theater education and after the conclusion, the final results were obtained through the in-depth interviews of the participants' parents and teachers. As a result, it was found that Social Skills Rating System(SSRS)' test, teachers' observation logs, interviews, and responses of participating children, which are the main subjects of this activity, had a great effect on improving their sociality and relationship. Therefore, the researcher tried to prove through this paper that theater education is effective in enhancing social skills as creative, personality and convergence education in preparation for the 4th industrial era and that it is important to solve communication problems such as the absence of human relationships.

• Clean Technology
• /
• v.15 no.4
• /
• pp.258-264
• /
• 2009

Thermodynamic measurements were performed to show the possibility of recovering $CO_2$ from fuel gas (the mixture of $CO_2$ and $H_2$) by forming gas hydrates with water where water was dispersed in the pores of silica gel particles having nominal 100 nm of pore diameter. The hydrate-phase equilibria for the ternary $CO_2+H_2$+water in pores were measured and $CO_2$ concentrations in vapor and hydrate phase were determined under the hydrate-vapor two phase region at constant 274.15 K. It was shown that the inhibition effect appeared due to silica gel pores, and the corresponding equilibrium dissociation pressures became higher than those of bulk water hydrates at a specific temperature. In addition, direct measurement of $CO_2$ content in the hydrate phase showed that the retrieved gas from the dissociation of hydrate contained more than 95 mol% of $CO_2$ when 42 mol% of $CO_2$ and balanced Hz mixture was applied. Compared with data obtained in case of bulk water hydrates, which showed just 83 mol% of $CO_2$ where 2-stage hydrate slurry reactor was intended to utilize this property, the hydrate formation in porous silica gel has enhanced the feasibility of $CO_2$ separation process. Hydrate formation as not for slurry but solid particle makes it possible to used fixed bed reactor, and can be a merit of well-understood technologies in the industrial field.

• Clean Technology
• /
• v.16 no.3
• /
• pp.213-219
• /
• 2010

Vortex tube is the device that can separate small particles from the compressed gas, as well as compressed gas into hot and cold gas. Due to energy and particle separation ability, a vortex tube can be used as the main component of the $CO_2$ absorption device. In this study, experimental approach has been performed to analyze the energy separation characteristics of the vortex tube. To obtain the preliminary design data, energy separation characteristics of the vortex tube has been tested for orifice diameter, nozzle area ratio, and tube length. As a result, the orifice diameter is the major factor of the vortex tube design. The nozzle area ratio and tube length have a minor effect on the energy separation performance. For Dc=0.6D, AR=0.14~0.16, and L=16D, maximum energy separation has been occurred. The result from this study can be used as the basic design data of the $100Nm^3$/hr class vortex tube applied to the $CO_2$ absorption device. Compared with the $CO_2$ absorption process containing an absorption tower, the process with a vortex tube is expected to have a huge advantage of saving the installation space and the operating cost.

• Applied Chemistry for Engineering
• /
• v.34 no.2
• /
• pp.192-198
• /
• 2023

In this study, the components of microwave-assisted extracts obtained from Thuja orientalis leaves were analyzed, and the cytotoxicity, antibacterial and antiviral activities were evaluated. The predominant components from microwave-assisted extraction were catechin, leucopelargonidin, arecatannin, quinolone, and kaempferol derivatives, which are classified in the flavonoid and tannin groups. We observed that the 0.11 mg/mL of extract concentration did not show cytotoxicity in HaCaT cells. The antibacterial activities were tested according to the guidelines of methods for determining the bactericidal activity of antimicrobial agents. The extracts showed 99.9% antibacterial efficiency against gram-positive S. aureus, while the antibacterial effect on gram-negative E. coli was insignificant. When the extract concentration and contact time with bacteria were increased, 99.9% antibacterial efficiency was observed for E. coli as well as S. aureus. Following the standard to assess the activity of microbicides against viruses in suspension (ASTM-E1052-20), the antiviral efficiency was more than 99.99% for influenza A (H1N1) and SARS-CoV-2. These results suggest its potential use in antiviral disinfectants, surface coatings, personal protective equipment, and textiles.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.1
• /
• pp.697-702
• /
• 2023

Recently, with the introduction of drones, a core technology of the 4th industrial revolution, various convergence education using drones is being conducted in school education sites. In particular, drone theory and practice education is being conducted in connection with free semester classes and career exploration. The drone convergence education program has higher learner satisfaction than simple demonstration and practice education, and the learning effect is high due to direct practical experience. However, since practical education is being conducted for a large number of learners, it is impossible to restrict and control the flight of a large number of drones in a limited place. In this paper, we propose a monitoring system that allows the instructor to monitor multiple drones in real time and learners to recognize collisions between drones in advance when multiple drones are operated, focusing on education operated in schools. The communication module used in the experiment was equipped with GPS in Murata LoRa, and the server and client were configured to enable monitoring based on the location data received in real time. The performance of the proposed system was evaluated in an open space, and it was confirmed that the communication signal was good up to a distance of about 120m. In other words, it was confirmed that 25 educational drones can be controlled within a range of 240m and the instructor can monitor them.

• Journal of Service Research and Studies
• /
• v.13 no.1
• /
• pp.76-95
• /
• 2023

As information and communications technology-based "smart hospitals" and "digital healthcare" have become a hot topic in the healthcare field, hospital mobile apps are gaining attention; but, the utilization rate is low due to lack of publicity, unstable systems, and late updates. In this situation, systematic research is needed to increase the utilization rate of hospital mobile apps, but related research has been rare. Therefore, this study integrates the information systems success model (ISSM) from the technical perspective and the expectation-confirmation model (ECM) from the cognitive perspective to demonstrate the influence mechanism on the continuous use intention of hospital mobile apps. For this purpose, an online survey was conducted among 181 Korean adults who have used hospital mobile apps. The results of the structual equation modeling showed that most of the quality factors have significant effects on expectation confirmation, perceived usefulness, and satisfaction. Additionally, expectation confirmation significantly affects perceived usefulness and satisfaction, and both perceived usefulness and satisfaction significantly affect the continuous use intention of hospital mobile apps. This study is of importance in that it integrates the ISSM and ECM and applies them to the context of using hospital mobile apps, which are underutilized in the healthcare field, and provides practical implications for increasing the utilization rate of hospital mobile apps and operating effective and efficient services through the findings.