• Journal of Korean Institute of Industrial Engineers
• /
• v.17 no.1
• /
• pp.59-73
• /
• 1991

In this paper, how to evaluate the assembly system was studied. The traction machine(TRM/C) is a kind of medium sized small quantity product. This work was performed on restriction of satisfying the customer's demand by simulating on the criteria of the queuing quantity in production system, the effectiveness of assembly machine and the average time spent on assembling. The problems about assembling were grasped through the analysis of products and process. The outputs of simulations that used SIMAN on four alternatives were evaluated on the basis of the average queuing quantity, the line effectiveness, the assembly time of a product and the production capacity.

• Journal of Korean Institute of Industrial Engineers
• /
• v.15 no.2
• /
• pp.87-91
• /
• 1989

A warranty is a contractual obligation incurred by a producer in connection with the sale of a product. The warranty specifies that producer agrees to remedy certain failures in the product sold. There have been many articles dealing with warranties, but they have studied about optimal warranty cost for the warranty period. In this study, an optimal preventive maintenance time interval is computed. The optimal preventive maintenance time interval minimizing warranty cost for the warranty period is discussed. It is assumed that failure rate is increasing and the failure rate after preventive maintenance or corrective maintenance lies between good as new and bad as old.

• Journal of Korean Institute of Industrial Engineers
• /
• v.15 no.2
• /
• pp.1-10
• /
• 1989

This paper deals with a single-facility multiproduction model concerning the basic cyclic scheduling. The aim is to obtain the production order of each product in a cycle and the cycle frequency for minimizing the setup costs and inventory carrying costs of all products. The problem is formulated by LP and it shows that the optimal solution derived dominates the solution of non-cyclic scheduling model on some conditions.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 2010.04a
• /
• pp.269-273
• /
• 2010

Remanufacturing is an industrial manufacturing process. The merits of remanufacturing are to reuse old products to perform like a new product and to save energy, natural resources, landfill space and to reduce air pollution by less re-smelting. This paper proposes a systemic approach for activating the domestic remanufacturing industry. The approach is based on inside and outside regulations to apply remanufacturing companies. And, we analyzed the state and problems of remanufacturing industry for automobile parts.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.23 no.59
• /
• pp.97-103
• /
• 2000

This study considers the design of life test sampling inspection plans by attributes for failure rate level qualification at selected confidence level. The lifetime distribution of products is assumed to be exponential. MIL-STD-690C and KS C 6032 standards provide this procedures. But these procedures have some questions to apply in the field. The cost of test and confidence level($1-{\beta}$ risk) are the problem between supplier and user. So, we suggest that the optimal life test sampling inspection plans using expected cost model considering product cost, capability, environmental test cost, etc.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.23 no.61
• /
• pp.89-98
• /
• 2000

For statistical process control, the process data are collected by the measurement system. But, the measurement system may have instrument error or/and operator error. In the measured values of products, the total observed variance consists of process variance and variance due to error of measurement system. In this paper, we design more practical T-s control chart considering estimated measurement error The effects of measurement error on the expected total cost and design parameters are investigated.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.9 no.14
• /
• pp.35-43
• /
• 1986

PL(product liability) is a major social, market, and economic force. The legal obligation of manufacturers and sellers to compensate for injury or damage caused by defective products is not a recent phenomenon. The concept of Product liability has been in existence for many years, but its emphasis has changed recently. This PL prevention program has shown that the two area of product quality assurance one is a PLD(product liability defense) and the other is a PLP(product liability prevention.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.22 no.52
• /
• pp.355-363
• /
• 1999

As the indirect cost is increasing, ABC(Activity-Based Costing) Method that can distribute the indirect cost to each products is more effectively used. Especially for a Hospital to provide better medical service with patients, It's necessary that build ABC System to provide a regular cost information. This study proposed methodology enabling accurate cost analysis from importing concepts of ABC in a Hospital and presented a Cost Information Table for Work-Time Table and Output Services to calculate ABC.

• Bulletin of the Korean Chemical Society
• /
• v.7 no.2
• /
• pp.142-145
• /
• 1986

Vinylation of highly hindered ${\beta}$-acetoxyvinyl mercurials with olefins in acetonitrile at room temperature in the presence of cupric chloride, as a reoxidant for the palladium, and a catalytic amount of $LiPdCl_3$ gave the corresponding conjugated dienes in moderate to good yields. The (E) or (Z) geometry in vinyl mercurials was retained in the vinylated products. The reaction was tolerant of a wide variety of functional groups ($CO_2$R, CN, OR, OAc) on either the vinyl mercurial or olefin compounds.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.24 no.65
• /
• pp.1-9
• /
• 2001

Enterprises confronted the Environment of infinite competition should be prepared to abrupt variations of management environment and have the ability to be changed in short term. It has to be studied, the control method of products that correspond to molt-functionalization and reduced product life which is caused by high-quality and varied customers demands. As a process control method, we must be able not only to control varies characteristic in a control at once but also to detected special values quickly for high-quality. In this paper a control method referred above is presented.