• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.1
• /
• pp.43-49
• /
• 1999

We propose a nonlinear feedback controller that can control the induction motors with high dynamic performance and high power efficiency by means of decoupling of motor speed and rotor flux. The nonlinear feedback controller needs the information on some motor parameters. New recursive adaptation algorithms for rotor resistance and mutual inductance which can be applied to our nonlinear feedback controller are also presented in this paper. The recursive adaptation algorithms make the estimated values of rotor resistance and mutual inductance track their real values. Some simulation and experimental results show that the adaptation algorithms are robust against the variation of stator resistance and stator inductance.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.7 s.361
• /
• pp.23-28
• /
• 2007

A dual-band GaAs FET low noise amplifier (LNA) with an input LC-tank circuit is designed using inductance source feedback for wireless LAN, and output matching is realized with low-pass Cheyshev filter impedance transforming circuit. Some design techniques for dual band LNA have been developed including input and output design equations. The measured results shows close agreement with the predicted performance.

• Journal of Power Electronics
• /
• v.15 no.3
• /
• pp.577-586
• /
• 2015

The combination of voltage feedforward and feedback control is a conventional approach for correcting the power factor in single-phase ac-dc boost converters. The feedback duty ratio increases significantly with an increase of the line frequency and input inductance. Therefore, the performance of the conventional approach is highly dependent on the bandwidth of the feedback controller. As a result, the input power quality can be significantly exacerbated due to uncompensated duty ratios if the feedback controller is limited. This paper proposes an input impedance and current feedforward control method to reduce the control portion of the feedback controller. The findings in this paper are 1) the theoretical derivation and analysis of variations of line frequency and input inductance on a power factor correction approach, 2) guaranteed consistent performance in a wide range of conditions, and 3) that a low switching frequency can be utilized by the proposed method. A MATLAB/Simulink model and a 1.2kW dual boost converter are built to demonstrate the effectiveness of the proposed method.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1253-1256
• /
• 1996

In this paper, a new nonlinear feedback linearization control scheme for induction motors is developed. The control scheme employs a fuzzy nonlinear identification scheme based on fuzzy basis function expansion to adoptively compensate the parameter variations, i.e. rotor resistance, mutual and self inductance etc. An important feature of the proposed control scheme is to incorporate the sliding mode controller into the scheme to speed up convergence rate. Simulation tests show the robust behavior of the proposed controller in the presence of the parameter uncertainties of the machine.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.234-238
• /
• 1998

Parameter estimation of induction motor for vector control presented in this paper can be easily implemented and applied to inverters in the industrial field, because it needs no additional hardware such as voltage sensor and measuring equipment. At first, the stator resistance including switching loss of inverter is measured by simple voltage-current equation. Next, in pre-magnetization of machine by imposing the d-axis constant field-current, q-axis torque current is forced to the machine until its speed feedback reachs to pre-defined level of speed limit. At this time, we can measure the rotor time-constant by decreasing the distorted output-voltage of inverter. At last, stator inductance, transient inductance, and moment of inertia can be measured by the relationship of output voltage, output torque and speed feedback. The validity and usufulness of this method is verified by experimental results.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.125-129
• /
• 2008

A low-voltage active CMOS inductor approach, which can improve the quality-factor(Q), is proposed in this paper. A low-voltage active inductor circuit topology with a feedback resistance is proposed, which can substantially improve its equivalent inductance and quality-factor(Q). This proposed low-voltage active inductor with a feedback resistance was simulated by ADS(Agilent) using 0.18um standard CMOS technology. Simulation showed that the designed active inductor had a maximum quality-factor(Q) of 3000 with a 1.5nH inductance at 4GHz

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.1
• /
• pp.42-46
• /
• 2003

In this paper, an MMIC broadband amplifier for wireless communication systems has been developed by using an active feedback method. This active feedback operates at much higher frequencies than a method by a spiral inductor feedback and its size is independent of the inductance value. The MMIC broadband amplifier was designed using a $0.5{\;}{\mutextrm{m}}$ MESFET library. The fabricated chip area was $1.4{\;}mm{\;}{\times}{\;}1.4{\;}mm. Measurement showed a gain of 18 dB with a gain flatness of ${\pm}3$ dB in a 1.5 GHz~3.5 GHz band. The maximum output power and the minimum noise figure were 14 dBm and 2.5 dB in the same band, respectively.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.239-244
• /
• 1998

We propose a nonlinear feedback controller that can control the induction motors with high dynamic performance by means of decoupling of motor speed and rotor flux. A new recursive adaptation algorithm for rotor resistance which can be applied to our nonlinear feedback controller is also presented in this paper. Some simulation results show that the adaptation algorithm for rotor resistance is robust against the variation of stator resistance and mutual inductance. In addition, it is computationally simple and has small estimation errors.

• Journal of Power Electronics
• /
• v.9 no.4
• /
• pp.604-611
• /
• 2009

A dP/dV feedback-controlled MPPT (Maximum Power Point Tracking) method for photovoltaic power systems using II-SEPIC (Isolated Inverse-SEPIC; Single Ended Primary Inductance Converter) is presented and a current-mode dP/dV feedback-controlled MPPT method is devised to apply for the PV power converter system. A control strategy for the current-mode dP/dV feedback control system is developed in this paper and the proposed MPPT shows relatively satisfactory dynamics against rapidly changing insolation conditions. In order to verify the validity and effectiveness of the proposed method, simulations and experiments of the PV power system using II-SEPlC converter are performed. These simulation and experiment results show that the proposed method enables the PV power system to extract maximum power from the photovoltaic module against the solar insolation variation.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.4
• /
• pp.443-450
• /
• 2014

This paper presents a 20-Gb/s optical receiver circuit fabricated with standard 65-nm CMOS technology. Our receiver circuits are designed with consideration for parasitic inductance and capacitance due to bonding wires connecting the photodetector and the circuit realized separately. Such parasitic inductance and capacitance usually disturb the high-speed performance but, with careful circuit design, we achieve optimized wide and flat response. The receiver circuit is composed of a transimpedance amplifier (TIA) with a DC-balancing buffer, a post amplifier (PA), and an output buffer. The TIA is designed in the shunt-feedback configuration with inductive peaking. The PA is composed of a 6-stage differential amplifier having interleaved active feedback. The receiver circuit is mounted on a FR4 PCB and wire-bonded to an equivalent circuit that emulates a photodetector. The measured transimpedance gain and 3-dB bandwidth of our optical receiver circuit is 84 $dB{\Omega}$ and 12 GHz, respectively. 20-Gb/s $2^{31}-1$ electrical pseudo-random bit sequence data are successfully received with the bit-error rate less than $10^{-12}$. The receiver circuit has chip area of $0.5mm{\times}0.44mm$ and it consumes excluding the output buffer 84 mW with 1.2-V supply voltage.