• Geomechanics and Engineering
• /
• 제4권2호
• /
• pp.135-150
• /
• 2012

This paper presents the study of the effect of microorganism Bacillus pasteurii on the properties such as Atterbergs' limit and unconfined compressive strength of cohesive soils. The results of this study reveal that the liquid limit and plasticity index for all clay soils decreased and the unconfined compressive strength increased. Decrease in plasticity index is very high for Kuttanad clay followed by bentonite and laterite. The unconfined compressive strength increased for all the soils. The increase was high for Kuttanad soil and low for laterite soil. After 24 h of treatment the improvement in the soil properties is comparatively less. Besides the specific bacteria selected Bacillus pasteurii, other microorganisms may also be taking part in calcite precipitation thereby causing soil cementation. But the naturally present microorganisms alone cannot work on the calcite precipitation.

• 지질공학
• /
• 제13권3호
• /
• pp.335-344
• /
• 2003

본 연구에서는 전라남도 장성과 화순에 분포하는 석회암풍화토의 물성 및 전단 특성을 연구하였다. 석회암풍화토의 교란시료에 대한 물성 및 전단 특성을 파악하기 위하여 실내 시험이 수행되었다. 연구지역의 석회암풍화토에 대한 물성 및 전단 특성은 다음과 같다 비중(Gs)은 2.78~2.80, 액성한계(LL)는 37~38(%), 소성지수(PI)는 13.7~15.4이며 흙의 분류(USCS)는 CL에 해당된다. 불포화 시료의 직접전단시험 (vd, $1.5t/\textrm{m}^3$)에 의한 강도정수는 점착력(c)이 3.07~4.4 ($t/\textrm{m}^2$) 그리고 내부마찰각($\Phi$)은 $34.8~42.4^{\circ}$의 범위를 보인다. 화강암풍화토 (양, 1997; 문. 1998; 박, 1998)와 비교해 보면, 연구지역의 석회암 풍화토의 물리적 특성은 일반적으로 차이를 보이며, 전단 강도정수 중, 내부마찰각은 대체적으로 유사한 경향을 보이는 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.391-398
• /
• 2000

The index properties of cohesive soils play an important role to examine entire tendency of soil properties. Especially, the Atterberg limits have a good correlation with compression and shear strength of cohesive soils. However, these values strongly depend on their testing methods. In this study, for Pusan clays the Atterberg limits were peformed under different conditions; for example, four kinds of specimen preparation, two kinds of testing equipment, and four kinds of estimating method. And a laboratory vane test was peformed to compare the undrained shear strength with that of the fall cone test. As experimental results, the value of liquid limit performed for oven-dried sample, followed in ASTM D4318, underestimated by about 10% compared to those of another three methods, irrespective to the used equipments. But the value of plastic limit was not influenced by sample preparation methods and equipments. The liquid limits by one-point methods(Leroueil et al., 1996; Nagaraj et al., 1981) were agreed well with those of different methods. Finally, the undrained shear strength by laboratory vane test was relatively larger than that of fall cone test, and the relationship between both showed a bad trend.

• Geomechanics and Engineering
• /
• 제33권5호
• /
• pp.453-462
• /
• 2023

Intermediate Geomaterials (IGMs) are natural formation materials that exhibit the engineering behavior (strength and compressibility) between soils and rocks. The engineering behavior of such material is highly unpredictable as the IGMs are stiffer than soils and weaker/softer than rocks. Further, the characterization of such material needs exposure to both soil and rock mechanics. In most conventional designs of geotechnical structures, the engineering properties of the IGMs are either aligned with soils or rocks, and this assumption may end up either in an over-conservative design or under-conservative design. Hence, many researchers have attempted to evaluate its actual engineering properties through laboratory tests. However, the test results are partially reliable due to the poor core recovery of IGMs and the possible sample disturbance. Subsequently, in-situ tests have been used in recent years to evaluate the engineering properties of IGMs. However, the respective in-situ test finds its limitations while exploring IGMs with different geological formations at deeper depths with the constraints of sampling. Standard Penetration Test (SPT) is the strength-based index test that is often used to explore IGMs. Moreover, it was also observed that the coefficient of variation of the design parameters (which represents the uncertainties in the design parameters) of IGMs is relatively high, and also the studies on the probabilistic characterization of IGMs are limited compared with soils and rocks. With this perspective, the present article reviews the laboratory and in-situ tests used to characterize the IGMs and explores the shear strength variation based on their geological origin.

• 한국산학기술학회논문지
• /
• 제13권9호
• /
• pp.4253-4258
• /
• 2012

본 연구에서는 고소성토 비배수강도와 주요 특성치들의 관계에 대하여 다양한 현장 및 실내시험 결과를 활용하여 심층적으로 고찰하였다. 소성지수, 활성도, 함수비 및 유효단위중량 등은 비배수강도 및 정규화 비배수강도 경우 모두 예상과 달리 특별한 관계를 보이지 않았다. 과압밀비, 예민비 및 비배수탄성계수 등은 정규화 비배수강도와 분명한 관계를 보여주었다. 정규화 비배수강도 방법이 비배수강도와 특성치들의 연구에 크게 도움이 될 것으로 기대된다.

• Geomechanics and Engineering
• /
• 제18권5호
• /
• pp.535-543
• /
• 2019

Building on/with expansive soils with no treatment brings complications. Compacted expansive soils specifically fall short in satisfying the minimum requirements for transport embankment infrastructures, requiring the adoption of hauled virgin mineral aggregates or a sustainable alternative. Use of hauled aggregates comes at a high carbon and economical cost. On average, every 9m high embankment built with quarried/hauled soils cost $12600MJ.m^{-2}$ Embodied Energy (EE). A prospect of using mixed cutting-arising expansive soils with industrial/domestic wastes can reduce the carbon cost and ease the pressure on landfills. The widespread use of recycled materials has been extensively limited due to concerns over their long-term performance, generally low shear strength and stiffness. In this contribution, hydromechanical properties of a waste tyre sand-sized rubber (a mixture of polybutadiene, polyisoprene, elastomers, and styrene-butadiene) and expansive silt is studied, allowing the short- and long-term behaviour of optimum compacted composites to be better established. The inclusion of tyre shred substantially decreased the swelling potential/pressure and modestly lowered the compression index. Silt-Tyre powder replacement lowered the bulk density, allowing construction of lighter reinforced earth structures. The shear strength and stiffness decreased on addition of tyre powder, yet the contribution of matric suction to the shear strength remained constant for tyre shred contents up to 20%. Reinforced soils adopted a ductile post-peak plastic behaviour with enhanced failure strain, offering the opportunity to build more flexible subgrades as recommended for expansive soils. Residual water content and tyre shred content are directly correlated; tyre-reinforced silt showed a greater capacity of water storage (than natural silts) and hence a sustainable solution to waterlogging and surficial flooding particularly in urban settings. Crushed fine tyre shred mixed with expansive silts/sands at 15 to 20 wt% appear to offer the maximum reduction in swelling-shrinking properties at minimum cracking, strength loss and enhanced compressibility expenses.

• 한국지반공학회논문집
• /
• 제29권1호
• /
• pp.23-27
• /
• 2013

기후변화에 따른 토석류 발생과 그로 인한 피해가 세계적으로 증가 추세에 있다. 토석류 연구는 역학적 관점에서 파괴 후(post-failure) 거동에 해당하며 지반강도와 유동특성을 분석함으로써 특성화할 수 있다. 본 연구는 국내의 토석류 발생지역인 상주(화강암 풍화토), 인제(편마암 풍화토), 포항(이암 및 셰일) 지역을 대상으로 지반의 물성-전단강도 상관관계와 토석류의 유동특성을 평가하였다. 본 연구지역을 대상으로 스웨덴 낙하 콘(Swedish Fall cone) 시험장치를 이용하여 지반의 물성 및 지반강도 사이에 일정한 상관관계가 있음을 밝혔다. 실험결과에 따르면, 인제, 상주, 포항지역에서 채취된 시료에 대해 액성지수(IL)와 비배수 전단강도($C_{ur}$) 사이에 $C_{ur}=(1.2/I_L)^{3.3}$의 관계식이 성립한다. 토석류 흐름을 지배하는 항복응력은 재성형 비배수 전단강도에 상응하는 것으로 간주하고, Bingham 모델과 액성지수-항복응력 관계식을 이용하여 토석류의 유동성을 조사하였다. 유동해석은 국내 풍화토와 낮은 활성점토를 구분하여 적용하였다. 이때 액성지수는 액성한계를 기준으로 $I_L=1$, 1.5, 3.0으로 구분하여 비교분석하였다. 동일한 액성지수($I_L=1$)에 대해, 토석류의 발생 5분 경과 후 최대 이동거리는 250m에 다다른다. 액성지수가 3으로 증가 될 경우, 토석류의 이동거리를 5분까지 살펴본 결과, 국내 풍화토는 낮은 활성점토에 비해 2배 이상 큰 유동성이 있음을 알 수 있었다. 본 유동성 평가기술은 토석류 피해저감기술 전략수립에 활용할 수 있을 것으로 기대된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.1065-1078
• /
• 2009

The shear strength has been managed as an important factor in soil mechanics. The shear strength estimation model was developed to evaluate the shear strength using only a few soil properties by the linear regression analysis model which is one of the statistical methods. The shear strength is divided into two part; one is the internal friction angle ($\Phi$) and the other is the cohesion (c). Therefore, some valid soil factors among the results of soil tests are selected through the correlation analysis using SPSS and then the model are formulated by the linear regression analysis based on the relationship between factors. Also, the developed model is compared with the result of direct shear test to prove the rationality of model. As the results of analysis about relationship between soil properties and shear strength, the internal friction angle is highly influenced by the void ratio and the dry unit weight and the cohesion is mainly influenced by the void ratio, the dry unit weight and the plastic index. Meanwhile, the shear strength estimated by the developed model is similar with that of the direct shear test. Therefore, the developed model may be used to estimate the shear strength of soils in the same condition of study area.

• Geomechanics and Engineering
• /
• 제1권4호
• /
• pp.291-306
• /
• 2009

One-dimensional soil-column studies were carried out to understand the interaction of three industrial effluents namely amino acid ('highly acidic'), surfactant ('highly organic') and pharmaceutical ('organic and toxic') on the physicochemical behavior, index properties and shear strength of bentonite due to artificial contamination extending to nearly 300 days. Changes in inorganic and organic pollutants present in the effluents due to the interaction of the above effluents and soil were assessed to understand the physico-chemical behaviour. Batch and continuous modes of operation, 8 hrs and 16 hrs Hydraulic Retention Time [HRT] and 25%, 50% concentrations of effluents, were the parameters considered. Amino acid, surfactant and pharmaceutical effluents have shown a high variation in pH (7 to 8) after artificial contamination on bentonite that is their original characteristics of the above effluents have been completely reversed. Further, it is found that the shear strength of bentonite has reduced by about 20%, and with respect to liquid limit and plastic limit shows an increasing trend with time within the period of contamination.

• Geomechanics and Engineering
• /
• 제12권3호
• /
• pp.523-539
• /
• 2017

Clay soils are typical for their swelling properties upon absorption of water during rains and development of cracks during summer time owing to the profile desorption of water through the inter-connected soil pores by water vapour diffusion leading to evaporation. This type of unstable soil phenomenon by and large poses a serious threat to the strength and stability of structures when rest on such type of soils. Even as lime and cement are extensively used for stabilization of clay soils it has become imperative to find relatively cheaper alternative materials to bring out the desired properties within the clay soil domain. In the present era of catastrophic environmental degradation as a side effect to modernized manufacturing processes, industrialization and urbanization the creative idea would be treating the waste products in a beneficial way for reuse and recycling. Bottom ash and ecosand are construed as a waste product from cement industry. An optimal combination of bottom ash-eco sand can be thought of as a viable alternative to stabilize the clay soils by means of an effective dispersion dynamics associated with the inter connected network of pore spaces. A CATIA model was created and imported to ANSYS Fluent to study the dispersion dynamics. Ion migration from the bottom ash-ecosand pile was facilitated through natural formation of cracks in clay soil subjected to atmospheric conditions. Treated samples collected at different curing days from inner and outer zones at different depths were tested for, plasticity index, Unconfined Compressive Strength (UCS), free swell index, water content, Cation Exchange Capacity (CEC), pH and ion concentration to show the effectiveness of the method in improving the clay soil.