• Tunnel and Underground Space
• /
• v.11 no.1
• /
• pp.59-63
• /
• 2001

The total number of elastic constants of an anisotropic body is 9 and thus it is very difficult to measure these constants experimentally. The number of elastic constants can be reduced if a rock or rock mass is regarded as isotropic or transversely isotropic material. Since only 4 stress-strain relationships can be obtained, it is theoretically impossible to determine all 5 constants from a single uniaxial compression teat. Lekhnitskii overcame this problem by suggesting the fifth equation based on laboratory tests. But his equation is theoretically wrong and does not agree with experimental results. This paper describes the stress-strain relationships and the independent/dependent elastic constants of an anisotropic mass and suggests a testing mothed to determine 5 independent elastic constants for a transversely isotropic rock.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.31-38
• /
• 2004

PMN-PT, a piezoelectric single crystal, has many useful applications such as sensors and actuators. In this paper, all the elastic, piezoelectric, and dielectric constants of the PMN-32％PT single crystals were measured by the resonance method. For the rhombohedral symmetry, a total of twelve independent material constants were measured such as six elastic compliance constants at constant electric field, two dielectric constants at constant stress, and four piezoelectric constants d. Seven sets of crystal samples of each different geometry were prepared for the measurement of length-thickness extensional, thickness extensional, radial, length extensional and thickness shear modes of vibration, respectively. In order to check the validity of the measurement, experimental impedance spectrum of the PMN-PT crystal was compared with numerical data spectrum calculated with the measured material constants. The good agreement between the two spectra confirmed validity of the results in this paper.

• Tunnel and Underground Space
• /
• v.18 no.4
• /
• pp.252-262
• /
• 2008

In the uniaxial compressive test of a single specimen of transversely isotropic rock, its 5 independent elastic constants can not be defined since maximum 4 independent strain measurements are available theoretically. In order to solve this problem, one equation proposed by Saint Venant in 19C and confirmed by Lekhnitskii through the test experiences has been used for long time. Accordign to authors' experiences, however, this equation turned out to give erroneous elastic constants in some cases. Three new equations are suggested and their compatibilities are discussed in this paper. As the results of the analyses of the models, Lekhnitskii's suggested equation is effective for the specimen with the high dip angle whereas it results in the large erred output for that with dip angle less than $25{\sim}30$. It was found that the effectivenesses of three suggested equations and their compatibilities are subject to the dip angle and not to the amounts of elastic constants. Guide map to the selection of the compatible one of those suggested equations is presented as a result of the study.

• Tunnel and Underground Space
• /
• v.22 no.5
• /
• pp.346-353
• /
• 2012

Multi-specimen uniaxial compression test has been carried out in order to find the method to determine the five independent elastic constants from a single standard specimen of a transversely isotropic rock. Total 35 specimens of 7 different angles from a large block of rhyolite presenting the flow structure obviously are used in tests. This second report is to focus on the statistical evaluation of measured strains and analyzed elastic constants. And the determination of their true or near-true values is discussed. As the result of RSD analysis, it turns out that the reliability of measured strains is sufficiently obtained and Saint-Venant approximation is well applicable except 15 degree angled specimen in tests. RSD is decreasing on the increase of the angle of anisotropy. This tendency may be caused not only by the decreasing of the deviation of measured strains, but also by the better applicability of Saint-Venant approximation on the increase of angle. It can be concluded that the analyzed values are considered the near-true ones of five independent constants on the high reliability. But the variation of the apparent Young's modulus expected by these values is not proved to match the measured tendency. It is inferred that the factor to decrease the apparent Young's modulus and/or to increase the shear strain, is present in the test or in the nature of the anisotropy in consideration of this inconsistency.

• Structural Engineering and Mechanics
• /
• v.10 no.5
• /
• pp.441-449
• /
• 2000

In this study, the state equation for axisymmetric bending of laminated transversely isotropic circular plates on elastic foundation is established on the basis of three-dimensional elasticity. By using the expansions of Bessel functions, an analytical solution of the problem is presented. As a result, all the fundamental equations of three-dimensional elasticity can be satisfied exactly and all the independent elastic constants can be fully taken into account. Furthermore, the continuity conditions at the interfaces of plies can also be satisfied.

• Tunnel and Underground Space
• /
• v.33 no.3
• /
• pp.150-168
• /
• 2023

The anisotropic behavior of rocks is primarily attributed to the directional arrangement of rock-forming minerals and the distribution characteristics of microcracks. Notably, sedimentary and metamorphic rocks often exhibit distinct transverse isotropy in terms of their strength and deformation characteristics. Consequently, it is crucial to gain accurate insights into the deformation and failure characteristics of transversely isotropic rocks during rock mechanics design processes. The deformation of such rocks is described by five independent elastic constants, which are determined through laboratory testing. In this study, the characteristics of the directional variation of apparent elastic constants in transversely isotropic rocks were investigated using experimental data reported in the literature. To achieve this, the constitutive equation proposed by Mehrabadi & Cowin was introduced to calculate the apparent elastic constants more efficiently and systematically in a rotated Cartesian coordinate system. Four transversely isotropic rock types from the literature were selected, and the influence of changes in the orientation of the weak plane on the variations of the apparent elastic modulus, apparent shear modulus, and apparent Poisson's ratio was analyzed. Based on the investigation, a new constraint on the elastic constants has been proposed. If the proposed constraint is satisfied, the directional variation of the apparent elastic constants in transversely isotropic rocks aligns with intuitive predictions of their tendencies.

• Advances in aircraft and spacecraft science
• /
• v.2 no.3
• /
• pp.249-261
• /
• 2015

The mechanical characterization of composite materials is nowadays a major interest due to their increasing use in the aeronautic industry. The design of most of these materials is based on their stiffness, which is mainly obtained by means of tensile tests with strain gauge measurement. For thin laminated composites, this classical method requires adequate samples with specific orientation and does not provide all the independent elastic constants. Regarding ultrasonic characterization, especially immersion technique, only one specimen is needed and the entire determination of the stiffness tensor is possible. This paper presents a study of different methods to determine the mechanical properties of transversely isotropic carbon fibre composite materials (gauge and correlation strain measurement during tensile tests, ultrasonic immersion technique). Results are compared to ISO standards and manufacturer data to evaluate the accuracy of these techniques.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.631-635
• /
• 1996

Stress singularities appear at the interface edge in dissimilar materials also under thermal loading. First, these singularities then an interface meets a free side surface with an arbitrary angle are studied for a two-dimensional problem. The singular properties under thermal loading are made clear and the concrete singular field are obtained. Secondly, the dependence of stress field on elastic constants in axisymmetric dissimilar materials are. discussed. That is, it is shown that three elastic constants mutually independent are necessary, in general, to characterize the stress field of axisymmetric dissimilar materials, although Dunders' parameters defined for two-dimensional dissimilar materials have been often applied correspondingly also to axisymmetric problems.

• Tunnel and Underground Space
• /
• v.20 no.3
• /
• pp.153-168
• /
• 2010

A fifth equation is required to determine the five independent elastic constants of a transversely isotropic rock from compression test of a single specimen. As an approximation proposed by Saint-Venant has been used for long time, it may cause an erroneous result in some cases, especially for specimen with low angle of anisotropy. Three equations were suggested replacing this traditional equation and proved to be applicable by the model analysis in the previous studies. As Saint-Venant's approximation is turned out the same as the first one of them, it has the characteristics that the apparent Young's modulus is monotonously increasing according to the anisotropic angle. The methodology to analyze the elastic constants from four independent strain measurements by uniaxial compressive test of a single standard specimen is concisely described, and the necessity and compatibility of new suggested equations are discussed. Saint-Venant's approximation can determine the elastic constants close to true values and other equations may be unnecessary in specimens with medium to large angle. Nevertheless, they may become applicable because they can produce the almost same amount. For the specimens of small angle of anisotropy, Saint-Venant's approximation may result in out of general ranges or thermodynamic constraints, but other suggested equations can produce the almost true value. Thus they can be applied before other alternative equation is known. The guide map constructed by model study may decide the most compatible one of the three equations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.469-470
• /
• 2008

We have studied electro-optic characteristics as a function of splay elastic constants ($K_{11}$) in the fringe-field switching (FFS) mode using the LC with positive dielectric anisotropy. When $K_{11}$ is increased from 7.7pN to 11.7pN, a maximum transmittance is slightly increased and rising time become a little bit fast. However, operating voltage and threshold voltage is independent. In opposition to rising time, decay time is not affected by $K_{11}$. We already know that $K_{11}$ affects tilt angle of liquid crystals. Therefore, on the occasion of high $K_{11}$, liquid crystals are mainly affected by twist deformation because the higher $K_{11}$, the less tilt angle. In the FFS device, high $K_{11}$ is favorable to reduce tilt angle in on state and thus improve rising response time.