• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.212-214
• /
• 2004

It is widely recognized that the residual stress of weldment affects steel construction and causes fracture initiation of welded structures. It is necessary to know since the power plants adopt a variety of welding processes distribution and magnitude of residual stresses. Therefore the purpose of present study is to investigate the validity of the indentation method to measure residual stresses of steel plates by residual stresses measured form the specimens of hot reheater pipes, cold reheater pipes and feed water lines used in power plants.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.826-830
• /
• 1994

Making Brinell indentations facing each other near the crack tip is very effective method in increasing fatigue life. In this paper, fatigue test was performed after indentation to investigate the effect of thickness of specimen. The results show that fatigue lives increased my making indentation and retardation cycle is inverse proportional to thickness of specimen.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.390-395
• /
• 2008

This study is performed to understand three dimensional characteristics of weld residual stress for the surface weld on the stainless steel plate. AISI 304 plate with one path weld on the surface was used as a test specimen. Finite element analysis was done to analyze thermal transient and residual stress due to weld. The result of finite element analysis was validated by previous paper and measurement data. Among various techniques for residual stress measurement, instrumented ball indentation method was applied. The calculated residual stresses by finite element analysis showed good agreement with the measured results.

• 한국표면공학회지
• /
• 제53권2호
• /
• pp.80-86
• /
• 2020

This paper is concerned with type of imperfections present within the anodic oxide films on AA2024 and surface hardness of the anodic film measured after ink-impregnation. The anodic oxide films were formed for 25 min at 40 mA/㎠ and 15±0.5℃ and 300 rpm of magnet stirring rate in 20% sulfuric acid solution. The ink-impregnation allows clear observations of not only the imperfections within the anodic oxide films but also an indentation mark on the oxide film surface made by a pyramidal-diamond penetrator for the hardness measurement. There were observed four different regions in the anodic oxide films on AA2024 and the surface hardness of the anodic oxide films appeared to be crucially dependent on the type of defects, showing 60~100 H_v on the oxide surface region I with large size black defect, 100~140 H_v on the oxide surface region II with large size grey defect, 140~170 H_v on the oxide surface region III with mall size black and/or grey defects and 170~190 H_v on the oxide surface region IV without defects. The pyramidal indentation marks were observed to be distorted in the regions with a large size black and grey defects, while no distortion of the indentation mark was observed in the regions with small size defects and without visible defects.

• 한국기계가공학회지
• /
• 제17권5호
• /
• pp.8-15
• /
• 2018

Films with special properties (e.g., water-repellent films, optical films, anti-reflection films, and flexible films) are referred to as functional films. Recently, there has been interest in fine patterning methods for film fabrication. In particular there have been many studies that use a UV nanoimprint process involving a UV curing method. In this paper, a polymer film was fabricated by the UV nanoimprint process with a micro-pattern, and its durability was evaluated by a wear test and a nano-indentation test. The film mechanical properties (such as coefficient of friction, hardness, and modulus of elasticity) were measured. Moreover, the choice of PUA type resin used in the UV nanoimprint process was confirmed to impact the durability of the thin film. Despite making the polymer film samples using the same method and PUA type resin, different coefficient of friction, hardness, and modulus of elasticity values were obtained. PUA 4 resin had the most favorable coefficient of friction, hardness, and modulus of elasticity. This material is predicted to produce a high durability functional film.

• Advances in nano research
• /
• 제15권4호
• /
• pp.315-328
• /
• 2023

The main goal of the present study was to assess the effects of eggshell powder (ESP) and halloysite nanotubes (HNTs) on the mechanical properties of abaca fiber (AF)-reinforced natural composites. For this purpose, a limited number of indentation tests were first performed on the AF/polypropylene (PP) composites for different HNT and ESP loadings (0 wt.% ~ 6 wt.%), load amplitudes (150, 200, and 250 N), and two types of indenters (Vickers or conical). The Young's modulus, hardness and plasticity index of each specimen were calculated using the indentation test results and Oliver-Pharr method. The accuracy of the experimental results was confirmed by comparing the values of the Young's modulus obtained from the indentation test with the results of the conventional tensile test. Then, a feed-forward shallow artificial neural network (ANN) with high efficiency was trained based on the obtained experimental data. The trained ANN could properly predict the variations of the mentioned mechanical properties of AF/PP composites incorporated with different HNT and ESP loadings. Furthermore, the trained ANN demonstrated that HNTs increase the elastic modulus and hardness of the composite, while the incorporation of ESP reduces these properties. For instance, the Young's modulus of composites incorporated with 3 wt.% of ESP decreased by 30.7% compared with the pure composite, while increasing the weight fraction of ESP up to 6% decreased the Young's modulus by 34.8%. Moreover, the trained ANN indicated that HNTs have a more significant effect on reducing the plasticity index than ESP.

• 대한기계학회논문집A
• /
• 제37권11호
• /
• pp.1339-1347
• /
• 2013

기존 단축 크리프시험에서는 천이 크리프의 영향을 무시하고 정상상태 크리프만을 고려하기 때문에 실제 크리프 특성을 나타내지 못한다. 이에 본 연구에서는 천이크리프를 고려한 압입 크리프 물성평가법을 제시한다. 다양한 재료에 대해 구형압입시험 전산모사를 이용해 크리프 물성변화에 따른 거동을 살펴보고, 크리프 특성을 무차원 변수들의 회귀식으로 표현한다. 이를 토대로 천이크리프를 고려한 압입 크리프 물성평가 프로그램을 생성했다. 제시한 물성평가 프로그램을 통해 압입 하중-변위 곡선으로부터 크리프지수, 계수값들을 각각 1.1%, 2.3% 오차범위에서 예측할 수 있다.

• 한국재료학회지
• /
• 제13권1호
• /
• pp.53-58
• /
• 2003

For the rib materials in PDP(plasma display panel), an effective method to improve the mechanical properties is to form a composite material by reinforcing a glass matrix with rigid fillers, such as alumina and titania powders. In this study, two types of ribs with different volume percent of fillers and with different glass matrix were tested for hardness, Young's modulus with the Berkovich indentation. As a result, cracks appeared around at the load of 1345 mN for the dense type of rib, while porous one endured until 2427 mN without any crack formation. Young's modulus and hardness decreased at the range: 90∼65 GPa, 9∼4 GPa, respectively as a function of indent load. Thus, a new method with nanoindenter represents a possible evaluation method for mechanical properties of barrier ribs.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.155-155
• /
• 2014

The oxide film was formed in hydrogen induced cracking (HIC) environment by potentio-dynamic method. Corrosion potentials and rates of the X-65 and X-80 line pipe steels were -0.3495 $V_{SHE}$, $2.833{\times}10^{-3}A/cm^2$ and 0.2716 $V_{SHE}$ and $2.533{\times}10^{-3}A/cm^2$, respectively. Surface composition analysis of the oxide film contained sulfur. Thermodynamic analysis of the HIC solution chemistry suggested that the oxide phase consisted of iron sulfate. Dynamic nano-indentation method applied to determine nano-hardnesses of the oxide film and base metal hardness.

• 대한기계학회논문집
• /
• 제17권2호
• /
• pp.285-299
• /
• 1993

본 연구에서는 UBET를 이용한 프로그램을 개발하여 소성가공 문제에 적용하였 으며, 형단조 가공에서 형 내부의 재료의 비정상 유동을 해석할 수 있는 알고리듬을 제시하였다. 매 변형단계에서 요소별 가공경화를 고려하여 자동적으로 요소시스템 (element system)을 재구성함으로써, UBET에 의한 소성가공 문제 해석을 효율적으로 할 수 있도록 하였다. 축대칭 형단조 문제에 있어서 리브의 높이대 폭의 비가 1.0, 2.0일때 UBET 및 탄소성 유한요소법에 의하여 형 내부의 재료 층만 과정을 시뮬레이션 하였으며, 단조 하중, 다이 충만도 및 재료의 유동 경향을 분석하여 적절한 유동 모델 과 초기 소재의 형상을 구하였다. 모델 재료를 사용한 형단조 모의실험을 수행하여 재료유동 및 변형 단계별 단조 하중분포 등을 구하였으며, 해석결과와 비교 분석하였 다. 또한 후방압출(backward extrusion) 및 평두형 펀치에 의한 평판압입(flat pu- nch indentation) 문제를 해석하였다. 후방압출시 모서리부의 라운딩(rounding) 효 과가 재료 유동에 미치는 영향을 고려하였으며, 평두형 펀치에 의한 평판압입에서는 상당 소성변형률(equivalent plastic strain)의 분포를 탄소성 유한요소법(elastic plastic finite element method)에 의한 결과와 비교하였다.