• Steel and Composite Structures
• /
• v.44 no.6
• /
• pp.845-865
• /
• 2022

In this study, the performance of shear deficient reinforced concrete (RC) beams with rectangular cross-sections, which were externally bonded reinforced (EBR) with high strength CFRP and GFRP strips composite along shear spans, has been experimentally and analytically investigated under vertical load. In the study, the minimum CFRP and GFRP strips width over spacing were considered. The shear beam with turned end to a bending beam was investigated by applying different composite strips. Therefore various arising in each of strength, ductility, rigidity, and energy dissipation capacity were obtained. A total of 12 small-scaled experimental programs have been performed. Beam dimensions have been taken as 100×150×1000 mm. Four beams have been tested as unstrengthened samples. This paper focuses on the effect of minimum CFRP and GFRP strip width on behaviours of RC beams shear-strengthened with full-wrapping, U-wrapping, and U-wrapping+longitudinal bonding strips. Strengthened beams showed significant increments for flexural ductility, energy dissipation, and inelastic performance. The full wrapping strips applied against shear failure have increased the load-carrying capacity of samples 53%-63% interval rate. Although full wrapping is the best strengthening choice, the U-wrapping and U-wrapping+longitudinal strips of both CFRP and GFRP bonding increased the shear capacity by 53%~75% compared to the S2 sample. In terms of ductility, the best result has been obtained by the type of strengthening where the S5 beam was completely GFRP wrapped. The experimental results were also compared with the analytically given by ACI440.2R-17, TBEC-2019 and FIB-2001. Especially in U-wrapped beams, the estimation of FIB was determined to be 81%. The estimates of the other codes are far from meeting the experimental results; therefore, essential improvements should be applied to the codes, especially regarding CFRP and GFRP deformation and approaches for longitudinal strip connections. According to the test results, it is suggested that GFRP, which is at least as effective but cheaper than CFRP, may be preferred for strengthening applications.

• Journal of Animal Science and Technology
• /
• v.65 no.3
• /
• pp.638-651
• /
• 2023

The objective of this study was to quantitatively estimate the level of grazing area damage in outdoor free-range pig production using a Unmanned Aerial Vehicles (UAV) with an RGB image sensor. Ten corn field images were captured by a UAV over approximately two weeks, during which gestating sows were allowed to graze freely on the corn field measuring 100 × 50 m². The images were corrected to a bird's-eye view, and then divided into 32 segments and sequentially inputted into the YOLOv4 detector to detect the corn images according to their condition. The 43 raw training images selected randomly out of 320 segmented images were flipped to create 86 images, and then these images were further augmented by rotating them in 5-degree increments to create a total of 6,192 images. The increased 6,192 images are further augmented by applying three random color transformations to each image, resulting in 24,768 datasets. The occupancy rate of corn in the field was estimated efficiently using You Only Look Once (YOLO). As of the first day of observation (day 2), it was evident that almost all the corn had disappeared by the ninth day. When grazing 20 sows in a 50 × 100 m² cornfield (250 m²/sow), it appears that the animals should be rotated to other grazing areas to protect the cover crop after at least five days. In agricultural technology, most of the research using machine and deep learning is related to the detection of fruits and pests, and research on other application fields is needed. In addition, large-scale image data collected by experts in the field are required as training data to apply deep learning. If the data required for deep learning is insufficient, a large number of data augmentation is required.

• The Korean Journal of Physiology and Pharmacology
• /
• v.27 no.4
• /
• pp.325-331
• /
• 2023

α₁-adrenoceptors link via the G-protein Gq/G₁₁ to both Ca²⁺ entry and release from stores, but may also activate Rho kinase, which causes calcium sensitization. This study aimed to identify the subtype(s) of α₁-adrenoceptor involved in Rho kinase-mediated responses in both rat aorta and mouse spleen, tissues in which contractions involve multiple subtypes of α₁-adrenoceptor. Tissues were contracted with cumulative concentrations of noradrenaline (NA) in 0.5 log unit increments, before and in the presence of an antagonist or vehicle. Contractions produced by NA in rat aorta are entirely α₁-adrenoceptor mediated as they are competitively blocked by prazosin. The α_1A-adrenoceptor antagonist RS100329 had low potency in rat aorta. The α_1D-adrenoceptor antagonist BMY7378 antagonized contractions in rat aorta in a biphasic manner: low concentrations blocking α_1D-adrenoceptors and high concentrations blocking α_1B-adrenoceptors. The Rho kinase inhibitor fasudil (10 µM) significantly reduced aortic contractions in terms of maximum response, suggesting inhibition of α_1B-adrenoceptor mediated responses. In the mouse spleen, a tissue in which all 3 subtypes of α₁-adrenoceptor are involved in contractions to NA, fasudil (3 µM) significantly reduced both early and late components to the NA contraction, the early component involving α_1B- and α_1D-adrenoceptors, and the late component involving α_1B- and α_1A-adrenoceptors. This suggests that fasudil inhibits α_1B-adrenoceptor mediated responses. It is concluded that α_1D- and α_1B-adrenoceptors interact in rat aorta and α_1D-, α_1A- and α_1B-adrenoceptors interact in the mouse spleen to produce contractions and these interactions suggest that one of the receptors preferentially activates Rho kinase, most likely the α_1B-adrenoceptor.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2022.10a
• /
• pp.63-63
• /
• 2022

Wheat flour can be categorized into bread, all-purpose, cake flour according to its protein content. Since optimal wheat flour protein content is different for each end use, it is necessary to diversify the nitrogen fertilizer methods depending on the end use and cultivar. Optimal wheat flour protein content of soft wheat (for cake flour) is lowest (<=10%) among all end use, it is necessary to develop nitrogen fertilizer methods for high yield and low protein content. In order to analyze the yield and quality changes of soft wheat as nitrogen fertilizer amount and splitting timing, soft wheat cultivar 'goso' was sown on paddy soil in jeunju, Republic of Korea ('21.10). the amount of nitrogen fertilizer was divided into 4 levels by adjusting 2kg/10a increments from 5.1 to ll.lkg/lOa, and in the N 7.1 and 9.1 kg/1 Oa(standard) treatment, N amount divided into sowing date:regrowing stage=3:7,4:6(standard), 5:5. In regrowing stage, Tiller number and N fertilizer amount at sowing date showed a correlation; y=-121.14x²+792.66x-525.41 (R²=0.77^*, y: Tiller number/m², x: N amount at sowing date(kg/10a)). Tiller number in regrowing stage was the highest when the nitrogen fertilizer amount at sowing date was 3.23kg/10a. spike number per m² was the highest when N fertilizer was divided into sowing date:regrowing stage=3:7(N amount: 9.1kg/10a). If N fertilizer amount was fixed, grain yield was also the highest when N fertilizer was divided into sowing date :regrowing stage=3:7. Also, N amount at sowing date and grain yield showed no correlation, but N amount at regrowing stage and grain yield showed significant correlation. As N amount increased, protein content also showed a tendency to increase.

• Journal of radiological science and technology
• /
• v.47 no.1
• /
• pp.39-48
• /
• 2024

In this study, we optimized the FNLM algorithm through a simulation study and applied it to a phantom scanned by low-dose CT to evaluate whether the FNLM algorithm can be used to obtain improved image quality images. We optimized the FNLM algorithm with MASH phantom and FASH phantom, which the algorithm was applied with MATLAB, increasing the smoothing factor from 0.01 to 0.05 with increments of 0.001 and measuring COV, RMSE, and PSNR values of the phantoms. For both phantom, COV and RMSE decreased, and PSNR increased as the smoothing factor increased. Based on the above results, we optimized a smoothing factor value of 0.043 for the FNLM algorithm. Then we applied the optimized FNLM algorithm to low dose lung CT and lung CT under normal conditions. In both images, the COV decreased by 55.33 times and 5.08 times respectively, and we confirmed that the quality of the image of low dose CT applying the optimized FNLM algorithm was 5.08 times better than the image of lung CT under normal conditions. In conclusion, we found that the smoothing factor of 0.043 among the factors of the FNLM algorithm showed the best results and validated the performance by reducing the noise in the low-quality CT images due to low dose with the optimized FNLM algorithm.

• Korean Journal of Agricultural Science
• /
• v.50 no.4
• /
• pp.773-784
• /
• 2023

In this study, we developed a dynamic model and steering controller model for an autonomous tractor and evaluated their performance. The traction force was measured using a 6-component load cell, and the rotational speed of the wheels was monitored using proximity sensors installed on the axles. Torque sensors were employed to measure the axle torque. The PI (proportional integral) controller's coefficients were determined using the trial-error method. The coefficient of the P varied in the range of 0.1 - 0.5 and the I coefficient was determined in 3 increments of 0.01, 0.05, and 0.1. To validate the simulation model, we conducted RMS (root mean square) comparisons between the measured data of axle torque and the simulation results. The performance of the steering controller model was evaluated by analyzing the damping ratio calculated with the first and second overshoots. The average front and rear axle torque ranged from 3.29 - 3.44 and 6.98 - 7.41 kNm, respectively. The average rotational speed of the wheel ranged from 29.21 - 30.55 rpm at the front, and from 21.46 - 21.63 rpm at the rear. The steering controller model exhibited the most stable control performance when the coefficients of P and I were set at 0.5 and 0.01, respectively. The RMS analysis of the axle torque results indicated that the left and right wheel errors were approximately 1.52% and 2.61% (at front) and 7.45% and 7.28% (at rear), respectively.

• Design & Manufacturing
• /
• v.18 no.2
• /
• pp.57-63
• /
• 2024

In this study, the recyclability of commonly used PP (polypropylene) and ABS (acrylonitrile butadiene styrene) was evaluated by molding test specimens from mixture of virgin and shredded material, followed by measuring their strength properties, Experiments were conducted o two type of PP (transparent and non-transparent) and two types of ABS (white and yellow). Test specimens for each resin were prepared with shredded material ratios ranging from 10% to 50% in 10% increments. Changes in tensile strength, elastic modulus, and elastic limit were analyzed based on the mixing ratio of the shredded material. The experimental results demonstrated that the strength properties of all the resins remained consistent within a certain range, even with increasing proportions of shredded material. For transparent PP, the tensile strength ranged from 30.87± MPa, the elastic modulus from 1.23±0.04 GPa, and the elastic limit from 19.17±0.44%. Non-transparent PP exhibited a tensile strength ranging from 27.71±0.58 MPa, an elastic modulus from 1.03±0.06 GPa, and an elastic limit from 17.35±0.41%. For ABS, white ABS had a tensile strength of 39.42±0.28 MPa, an elastic modulus of 1.94±0.01 GPa, and an elastic limit of 36.76±0.25%. Yellow ABS showed a tensile strength of 39.25±0.78 MPa, an elastic modulus of 1.94±0.01 GPa, and an elastic limit of 37.14±0.23%, with values remaining consistent within this range. Based on these results, it was confirmed that the mechanical properties of the resins used in this study do not change significantly when mixed with recycled shredded material, indicating excellent mechanical recyclability.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.4
• /
• pp.43-47
• /
• 2024

This paper introduces a phased-array single-channel transceiver beamformer IC built using 65nm CMOS technology, covering the 8-16 GHz range and targeting the X and Ku bands for radar and satellite communications. Each signal path in the IC features a low noise amplifier (LNA), power amplifier (PA), phase shifter (PS), and variable gain amplifier (VGA), which allow for phase and gain adjustments essential for beam steering and tapering control in typical beamforming systems. Test results show that the phase-compensated VGA offers a gain range of 15 dB with 0.25 dB increments and an RMS gain error of 0.27 dB. The active vector modulator phase shifter delivers a 360° phase range with 2.8125° steps and an RMS phase error of 3.5°.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.1
• /
• pp.66-78
• /
• 2004

The objective of this study was to apply the vibration technique to reduce the viscosity of bonding adhesives and thereby compare the bond strength and resin penetration in enamel and dentin achieved with those gained using the conventional technique and vibration technique. For enamel specimens, thirty teeth were sectioned mesio-distally. Sectioned two parts were assigned to same adhesive system but different treatment(vibration vs. non-vibration). Each specimen was embedded in 1-inch inner diameter PVC pipe with a acrylic resin. The buccal and lingual surfaces were placed so that the tooth and the embedding medium were at the same level. The samples were subsequently polished silicon carbide abrasive papers. Each adhesive system was applied according to its manufacture's instruction. Vibration groups were additionally vibrated for 15 seconds before curing. For dentin specimen, except removing the coronal part and placing occlusal surface at the mold level, the remaining procedures were same as enamel specimen. Resin composite(Z250. 3M. U.S.A.) was condensed on to the prepared surface in two increments using a mold kit(Ultradent Inc., U.S.A.). Each increments was light cured for 40 seconds. After 24 hours in tap water at room temperature, the specimens were thermocycled for 1000cycles. Shear bond strengths were measured with a universal testing machine(Instron 4465, England). To investigate infiltration patterns of adhesive materials, the surface of specimens was examined with scanning electron microscope. The results were as follows: 1. In enamel the mean values of shear bond strengths in vibration groups(group 2, 4, 6) were greater than those of non-vibration group(group 1, 3, 5). The differences were statistically significant except AQ bond group. 2. In dentin, the mean values of shear bond strengths in vibration groups(group 2, 4, 6) were greater than those of non-vibration groups(group 1, 3, 5). But the differences were not statistically significant except One-Up Bond F group. 3. The vibration group showed more mineral loss in enamel and longer resin tag and greater number of lateral branches in dentin under SEM examination.

• Clinical and Experimental Pediatrics
• /
• v.45 no.9
• /
• pp.1075-1082
• /
• 2002

Purpose : Obesity is known to be associated with hypertension, dyslipidemia, and fatty liver and is thought to be associated with increased levels of free fatty acids. One of the strategies for decreasing free fatty acid levels is stimulation of hepatic lipid oxidation with L-carnitine. Carnitine is an essential cofactor for transport of long-chain fatty acid into mitochondria for oxidation. This study was designed to evaluate the changes of serum fatty acids and carnitine levels after exogenous injection of L-carnitine. Methods : Sprague Dawley rats were divided into two groups. Group A was control. Group B was given intraperitoneal injection with L-carnitine(200 mg/kg) daily for two weeks. Serum lipid (total cholesterol, triglyceride, HDL-cholesterol, LDL-cholesterol) and fatty acid levels were analyzed on the first day of the first and second weeks after injection of L-carnitine. Total, free, and acyl carnitine levels also were performed by a enzymatic cycling techniques at the same day intervals. Results : There was no significant difference between the two groups in total cholesterol, HDL-cholesterol, LDL-cholesterol levels before and after the administration of L-carnitine. But triglyceride levels were significantly decreased at the first week in group B compared with group A. Among free fatty acids, linoleic acid showed significant decrement(A group : $131.3{\pm}31.3mg/dL$ vs B group : $90.0{\pm}7.0mg/dL$) at the first week. Total, free, and acyl carnitine levels showed significant increments at all days intervals, but only free carnitine showed significant increments according to cumulative doses of carnitine. Conclusion : Plasma linoleic acid, a long-chain fatty acid, showed significant decrement after administration of L-carnitine in the first week. This may suggest that L-carnitine can be used as an antilipidemic agent for obese patients. A prospective study will investigate obese children in the future.