• The Korean Journal of Physiology
• /
• 제2권1호
• /
• pp.39-45
• /
• 1968

Recently, in this department, pressure-displacement curve and breaking tension of dog and human tympanic membrane were studied using intact, fresh or dried tympanic membrane attached to external auditory meatus. However, physical property, proper elasticity-Young Modulus, of the tympanic membrane has not been clarified yet. Present study is attempted to further clarify proper Young Modulus of tympanic membrane, and to distinguish possible difference between layer of stratum radiatum and layer of stratum circulare of tympanic membrane in breaking tension and in Young Modulus. Tympanic membrane was excised from sacrificed dog, and preparation was made into the size of approximately 1 mm in width and 3 mm in length. In fresh or dried tympanic membrane, which was dried at $80^{\circ}C$ for 24 hrs., some preparations were made along the long axis parallel to the fibers of radial direction, and others were made along the long axis perpendicular to the radial fibers-circular direction. Breaking tension and displacement according to loading, were measured and Young Modulus was calculated in tympanic membrane preparations under the different experimental conditions. Results obtained are summarized as follows : 1. Young Modulus of fresh tympanic membrane in radial direction was $6.57{\times}10^8\;dyne/cm^2$, and that of fresh preparation in circular direction was $1.68{\times}10^8\;dyne/cm^2$. The Young Modulus of fresh tympanic membrane in radial direction resembles to that of silk and whale moustache. In dried tympanic membrane, Young Modulus of preparation of radial direction was $30.2{\times}10^8\;dyne/cm^2$ and that of preparation in circular direction was $25.0{\times}10^8\;dyne/cm^2$. 2. Breaking tension of fresh tympanic membrane was 44.9 gm/mm in radial preparation, and 7.9 gm/mm in circular preparation. In dried tympanic membrane, breaking tension was 46.7 gm/mm in preparation of radial direction, and 17.2 gm/mm in preparation of circular direction. 3. Much smaller breaking tension of the circular preparation-one fifth to the radial preparation-seemed to be responsible for the higher incidence of circular fiber breaking in tympanic membrane performation caused by trauma or sudden change in atmospheric pressure. 4. The correlation seemed to be very close between breaking tension and Young Modulus in tympanic membrane.

• 한국동물위생학회지
• /
• 제30권1호
• /
• pp.133-144
• /
• 2007

This study was conducted to determine the effective environmental control measures in preventing calf diarrheal disease in farms. It was found that the high numbers of calves in a cow house was directly related with the high incidence rate of diarrheal diseases. When the number of calves was increased in a cow house, it was difficult to reduce the diarrheal diseases of calves. It was revealed that the incidence rates of calf diarrheal disease were dramatically reduced when the delivery house which faced south. The periodical changes of bedding materials seemed beneficial good to control the possible resident infectious agents, including pathogenic viruses and bacteria. The control of the delivery time was important for reduction of calf diarrhea. It was revealed that September and October were the best time as the delivery period. In order to use old cow house as a delivery house, it should be sterilized by the disinfectant and the flame. When the diarrheal feces were removed as soon as possible, the transmission of diarrheal diseases among calves In the same house was reduced. When the diarrheal feces were not disposed, the incidence rate of diarrhea reached up to 50%. When the morbid calves were not quarantined, the incidence rate of diarrhea was 100%. In contrast, when the diseased calves were quarantined from other calves, the incidence rate of diarrhea was reduced, remarkably. The mean recovery time from the diarrhea of the treated calves in the southern cow house was much faster than that in the north cow house. The treatment of calves in a clean and well-ventilated cow house with dry bedding was more effective than that in a cold, wet, and dark house. It could be postulated that the most important environmental factor in the reduction of diarrheal diseases of calves is the blocking of the entry of the infectious agents. The complete sanitation and control of the delivery house in the using farm is more important than building a new cow house, for prevention of calf diarrheal diseases.

• Imaging Science in Dentistry
• /
• 제38권2호
• /
• pp.103-107
• /
• 2008

Purpose: The purpose of this study was to evaluate the relationship between the position of mesiodens and its complications. Materials and Methods: The subjects for this study consisted of 172 patients with mesiodens. Panoramic radiographs and cross-sectional tomography were taken of all of the subjects. Their clinical records and radiographs were analyzed in order to study the direction and vertical and sagittal position of mesiodens, as well as complications caused by mesiodens. Results: The number of mesiodens was one in 112 cases (65.1%) and two in 60 cases (34.9%). Complications were found in 121 mesiodentes (52.2%), with being median diastema the most frequent. The incidence of complications was high in erupted mesiodens (75.0%), in horizontal mesiodens (89.8%) and in mesiodens located within the arch (75.7%), but was low in mesiodens impacted above apex (29.8%), in normal position (34.4%) and in palatally positioned mesiodens (46.5%). Conclusion: It was suggested that the frequency of complications was different according to the vertical position, the direction of the crown and the sagittal position.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.409-412
• /
• 2002

We found that polyimide surfaces bombarded by a low energy argon ion beam align liquid crystals. The pretilt angle of the liquid crystals is controlled by ion beam parameters, such as the energy of the incident ions, the angle of incidence, exposure time and current density. The alignment direction of liquid crystal on substrates corresponded to ion beam direction. By argon ion beam the pretilt angle of the liquid crystals was controlled between $0.5^{\circ}$ and $4^{\circ}$for SE-3140 under the proper conditons. By the atomic force microscope (AFM), polyimide surfaces before and after bombarded by ion beam are compared.

• 반도체디스플레이기술학회지
• /
• 제18권3호
• /
• pp.72-76
• /
• 2019

A Q-switched diode-pumped neodymium-doped yttrium vanadate (YVO₄, λ =1064nm) laser was used for the direct patterning of indium tin oxide (ITO) films on glass substrate. During the laser direct patterning, the laser beam was incident on the two different directions of glass substrate and the laser ablated patterns were compared and analyzed. At a low scanning speed of laser beam, the larger laser etched lines were obtained by laser beam incident in reverse side of glass substrate. On the contrary, at a higher scanning speed, the larger etched pattern sizes were found in case of the beam incidence from front side of glass substrate. Furthermore, it was impossible to find no ablated patterns in some laser beam conditions for the laser beam from reverse side at a much higher scanning speed and repetition rate of laser beam. The laser beam is expected to be transferred and scattered through the glass substrate and the laser beam energy is thought to be also dispersed and much more influenced by the overlapping of each laser beam spot.

• Wind and Structures
• /
• 제38권5호
• /
• pp.367-379
• /
• 2024

Compared with traditional transmission towers, T-shaped angle towers have long cross-arms and are specially used for ultrahigh-voltage direct-current (UHVDC) transmission. Nevertheless, the wind loads of T-shaped towers have not received much attention in previous studies. Consequently, a series of wind tunnel tests on the T-shaped towers featuring cross-arms of varying lengths were conducted using the high-frequency force balance (HFFB) technique. The test results reveal that the T-shaped tower's drag coefficients nearly remain constant at different testing velocities, demonstrating that Reynolds number effects are negligible in the test range of 1.26 × 10⁴-2.30 × 10⁴. The maximum values of the longitudinal base shear and torsion of the T-shaped tower are reached at 15° and 25° of wind incidence, respectively. In the yaw angle, the crosswind coefficients of the tower body are quite small, whereas those of the cross-arms are significant, and as a result, the assumption in some load codes (such as ASCE 74-2020, IEC 60826-2017 and EN 50341-1:2012) that the resultant force direction is the same as the wind direction may be inappropriate for the cross-arm situation. The fitting formulas for the wind load-distribution factors of the tower body and cross-arms are developed, respectively, which would greatly facilitate the determination of the wind loads on T-shaped angle towers.

• 보험의학회지
• /
• 제2권1호
• /
• pp.195-217
• /
• 1985

A statistical analysis on the ratio of weight-for-height in insurance medicine was carried out in a total of 12,690 insured persons who were medically examined at the Honam medical department, Dong Bang life insurance company, ltd. from June, 1979 to February, 1984. The results were as follows: 1. The mean value of the ratio of weight-for-height(W/H ratio) was $102.3{\pm}11.3%$ in all males, and $105.2{\pm}103.6%$ in all females. The difference of the values between males and females showed statistical significance(P<0.001). The mean value of W/H ratio in all the insureds was $103.8{\pm}12.9%$. In each age group, the mean value of female was higher than that of male without exception(P<0.001). The mean value of both sexes in each age group showed gradual increase with age except for the age group over 50(P<0.001). 2. The incidences of the average weighted, overweighted and underweighted lives were respectively 91.6% in all males, 84.2% in all females(P<0.001); 7.9% in all males, 15.4% in all females(P<0.001); 0.5% in all males, 0.4% in all females(P>0.05). The incidences of average weighted, overweighted and underweighted lives in all the insureds were respectively 87.6%, 12.0% and 0.5%. The incidence of the average weighted lives in male in each age group was always higher than that in female with the exception of the age group below 19(P<0.001), whereas the incidence of the overweighted lives in male in each age group was always lower than that in female(P<0.05 in the age group below 19, P<0.001 in the other age groups). The incidence of average weighted lives of both sexes in each age group showed gradual decrease with age from the second to fifth decade(P<0.001), whereas the incidence of the overweighted lives of both sexes in each age group showed gradual increase with age from the second to fifth decade(P<0.001). 3. The relative frequency distribution polygons of W/H ratio of both sexes drawn in a pair on one coordinate plane revealed lying in juxtaposition each other horizontally and showed the shifting of female's polygon to male's one toward the direction of greater value of W/H ratio at a short distance which increased gradually with age. 4. Correlations between both sexes and among age groups relating to W/H ratios of the insureds seem to be a physiological phenomenon of body build and should be considered on the rating of the build. Author prepared a rating table of build based on the correlations above menthioned. Some gradients by sex and age in the rating table of build are organized; in female group, the ratings of 0, 30-50, 50-100 and 100-D are to calculate by the build with W/H ratio of 80-125%, $126{\sim}145%,\;146{\sim}165%$ and over 166% respectively in the age group of 29 or under, by the build with W/H ratio of $80{\sim}130%,\;131{\sim}150%,\;151{\sim}170%$ and over 171% respectively in the age group of $30{\sim}59$, and by the build with W/H ratio of $80{\sim}135%,\;136{\sim}155%,\;156{\sim}175%$ and over 176% respectively in the age group of 60 or over. In male group, the ratings of 0, $30{\sim}50$, 50-100, and 100-D are to calculate by the build with W/H ratio of $80{\sim}120%,\;121{\sim}140%,\;141{\sim}160%$ and over 161% respectively in all ages. Of under weighted lives, in both sexes, the ratings of 30-50 and 50-D are to calculate by the build with W/H ratio of $76{\sim}79%$ and under 75% respectively. The results of the ratings according to a rating table by author were as follows: The incidence of the ratings of 0, 30-50, 50-100 and 100-D showed no difference between male and female. The incidence of the ratings of 0(indicating the average weighted lives) showed gradual decrease with age and the incidence of the ratings of 30-50 and 50-100(indicating the overweighted lives) showed gradual increase with age. These results are thought to be considerably reasonable because the incidence of the builds in each age group is supposed to have no difference by sex and the incidence of the overweighted lives would increase with age.

• 대한전자공학회논문지SP
• /
• 제48권5호
• /
• pp.96-101
• /
• 2011

Capon 알고리듬은 지향방향에 대하여 일정한 이득을 유지하면서 배열의 출력을 최소화 시키므로 FM (Fourier method) 알고리듬에 비하여 우수한 분해능 (resolution)을 제공한다. 그러나 Capon 알고리듬의 DoA (Direction of Arrival) 추정 성능은 입사 신호의 SNR (signal-to-noise ratio)이 낮은 경우 급격히 저하되는 문제가 있어 신호원들의 입사각이 유사한 경우 각각의 신호원을 구분하지 못하는 문제가 있다. 본 논문에서는 Capon 알고리듬에서 사용되는 공분산 역행렬의 원소를 제거하는 기법을 이용하여 수신 신호의 SNR이 낮은 환경에서 보다 나은 분해능을 제공하는 개선 방안을 제안한다.

• 수산해양기술연구
• /
• 제52권3호
• /
• pp.276-280
• /
• 2016

This study investigated luring distributions by water layer of common squid which were targeted by angling fishing vessels equipped with LED and metal-halide lamps using a scientific echosounder with a 120 kHz frequency in order to develop energy-effective underwater fish aggregation devices. In the analysis, angles of a transducer were changed from $0^{\circ}$ to $45^{\circ}$ and were rotated every $10^{\circ}$ horizontally. It was shown that common squid were densely distributed from the surface to 40 m and they were also distributed in directions of $10^{\circ}{\sim}+30^{\circ}$, $-30^{\circ}{\sim}-60^{\circ}$, and $-120^{\circ}{\sim}-130^{\circ}$with the head of vessel as the center. Comparative results of angles of transducer on acoustical densities of common squid distributing in 21~40 m water depth showed an average $101.8m^2/nm^2$ in vertical direction of $0^{\circ}$, $12.3m^2/nm^2$ in angle of $30^{\circ}$, and $42.4m^2/nm^2$ in angle of $45^{\circ}$, respectively. It implied that more considerations on acoustic scattering strength by incidence angle direction of the transducer and swimming oriental angle direction of common squid would be required.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.743-750
• /
• 2008

Asymmetric tip clearance in an axial compressor induces pressure and velocity redistributions along the circumferential direction in an axial compressor. This paper presents the mechanism of the flow redistribution due to the asymmetric tip clearance with a simple numerical modeling. The flow field of a rotor of an axial compressor is predicted when an asymmetric tip clearance occurs along the circumferential direction. The modeling results are supported by CFD results not only to validate the present modeling but also to investigate more detailed flow fields. Asymmetric tip clearance makes local flow area and resultant axial velocity vary along the circumferential direction. This flow redistribution 'seed' results in a different flow patterns according to the flow coefficient. Flow field redistribution patterns are largely dependent on the local tip clearance performance at low flow coefficients. However, the contribution of the main flow region becomes dominant while the tip clearance effect becomes weak as the flow coefficient increases. The flow field redistribution pattern becomes noticeably strong if a blockage effect is involved when the flow coefficient increases. The relative flow angle at the small clearance region decreases which result in a negative incidence angle at the high flow coefficient. It causes a recirculation region at the blade pressure surface which results in the flow blockage. It promotes the strength of the flow field redistribution at the rotor outlet. These flow pattern changes have an effect on the blade loading perturbations. The integration of blade loading perturbation from control volume analysis of the circumferential momentum leads to well-known Alford's force. Alford's force is always negative when the flow blockage effects are excluded. However when the flow blockage effect is incorporated into the modeling, main flow effects on the flow redistribution is also reflected on the Alford's force at the high flow coefficient. Alford's force steeply increases as the flow coefficient increases, because of the tip leakage suppression and strong flow redistribution. The predicted results are well agreed to CFD results by Kang and Kang(2006).