• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.67-70
• /
• 2000

Mechanical properties of (10%$AI_20_3{\cdot}SiO_2$+5%Ni)/Al hybrid composites fabricated by the reaction squeeze casting were compared with those of (15%$AI_20_3{\cdot}SiO_2$)/Al composites. Intermetallic compound formed by reaction between molten aluminum and reinforcing powder was uniformly distributed in the Al matrix. These intermetallic compounds were identified as $Al_3$NI using EDS and X-ray diffraction analysis. Microhardness and flexural strength of hybrid composites were higher than that of (15%$AI_20_3{\cdot}SiO_2$)/Al Composite. In-Situ fracture tests were Conducted on (15%$AI_20_3{\cdot}SiO_2$)/Al Composites and (10%$AI_20_3{\cdot}SiO_2$+5%Ni)/Al hybrid composites to identify the microfracture process. It was identified from the in-situ fracture test of (10%$AI_20_3{\cdot}SiO_2$+5%Ni)/Al composites, microcracks were initiated mainly at the short fiber / matrix interfaces. As the loading was continued, the crack propagated mainly along the separated interfacial regions and the well developed shear bands. It was identified from the in-situ fracture test of (10%$AI_20_3{\cdot}SiO_2$+5%Ni)/Al hybrid composites, microcracks were initiated mainly by the short fiber/matrix interfacial debonding. The crack proceeded mainly through the intermetallic compound clusters

• Korean Chemical Engineering Research
• /
• v.56 no.5
• /
• pp.773-778
• /
• 2018

In-situ transesterification of microalgae lipids using microwave irradiation has potential to simplify and accelerate biodiesel production, as it minimizes production cost and reaction time by direct transesterification of microalgae into biodiesel with microwave as a heating source. This study was conducted to research the effect of microwave irradiation with in-situ transesterification of microalgae under base catalyst condition. The process variables (reaction time, solvent ratio, microwave power) were studied using 2% of catalyst concentration. The maximum yield of FAME was obtained at about 32.18% at the reaction time of 30 min with biomass-methanol ratio 1:12 (w/v) and microwave power of 450 W. The GC MS analysis obtained that the main component of FAME from microalgal oils (or lipids) was palmitic acid, stearic acid and oleic acid. The results show that microwaves can be used as a heating source to synthesize biodiesel from microalgae in terms of major components resulting.

• The Korean Journal of Rheology
• /
• v.10 no.2
• /
• pp.82-91
• /
• 1998

액정고분자/폴리카보네이트 혼합계로 구성된 분자복합계를 쉬트상으로 가공할 때 취 약해지기 쉬운 횡단면 방향의 물성을 향상시키기 위하여 미세섬유상의 배향을 in-situ 상태 로 적절히 제어할수 있는 Simultaneous Convergent-Divergent(SCD) 다이를 설계·제작하 고 압출실험을 수행하여 얻은 압출 쉬트를 대상으로 구조-물성-가공의 상관관계를 조사하 였다. 액정고분자의 첨가 함량에 따른 토오크와 토출량의 변화는 액정고분자를 10wt% 소량 첨가하였음에도 현저한 감소 효과를 보였으며 약 30wt%일 때 최소로되었다. 이는 액정고분 자가 보강 기능외에 가공특성의 개선에도 큰 효과가 있어 가공조제로서의 가능성을 보이는 결과로 혼합계의 유변학적 특성 결과에서도 확인할수 있었다. 또 DSC와 DMA를 이용한 열 분석 결과 액정고분자의 함량이 증가함에 따라 PC의 유리전이온도가 다소 감소하는 현상을 보임에 미루어 이 혼합계는 부분적으로 상용성을 갖는 것으로 볼수 있으며 모폴로지 분석을 통해서도 이를 확인할수 있었다. TLCP/PC 혼합계로 구성되는 분자복합재를 SCD 다이를 사용하여 제조한 압출 쉬트의 방향성에 따른 기계적 물성은 기존의 쉬트 다이보다 흐름방향 으로는 다소 낮은 물성치를 보이지만 횡단면 방향으로는 물성이 현저히 향상됨을 관찰할수 있었다. 모폴로지 분석결과 기존의 쉬트 다이의 경우 벽면 부근에서는 액정고분자가 미세섬 유상으로 형성되어 흐름방향으로 배향되어 있지만 중심부에서는 액정 상태로 존재하는 반 면, SCD 다이의 경우 미세섬유상으로 형성된 액정고분자가 벽면에서부터 중심부로 갈수록 횡단면 방향으로 서서히 배향되어 있음을 확인할수 있었다.

• Korean Journal of Metals and Materials
• /
• v.48 no.8
• /
• pp.780-789
• /
• 2010

The aim of this study is to evaluate the microstructure and tensile property of in-situ (TiB+TiC) particulate reinforced titanium matrix composites (TMCs) synthesized by the investment casting process. Boron carbide ($1,500{\mu}m$ and $150{\mu}m$) was added to the titanium matrix during vacuum induction melting, which can provide the in-situ reaction of $5Ti+B_4C{\rightarrow}4TiB+TiC$. 0.94, 1.88 and 3.76 wt% of $B_4C$ were added to the melt. The phases identification of the in-situ synthesized TMCs was examined using scanning electron microscopy, an X-ray diffractometer, an electron probe micro-analyzer and transmission electron microscopy. Tensile properties of TMCs were investigated in accordance with the reinforcement size and volume fraction. The improvement of tensile property of titanium matrix composites was caused by load transfer from the titanium matrix to the reinforcement and by grain refinement of titanium matrix and reinforcements.

• Journal of the Korean Applied Science and Technology
• /
• v.19 no.4
• /
• pp.335-338
• /
• 2002

A new process for polymeric gate insulator in field-effect transistors was proposed. Fourier transform infrared absorption spectra were measured in order to identify ODPA-ODA polyimide. Its breakdown field and electrical conductivity were measured. All-organic thin-film transistors with a stacked-inverted top-contact structure were fabricated to demonstrate that thermally evaporated polyimide films could be used as a gate insulator. As a result, the transistor performances with evaporated polyimide was similar with spin-coated polyimide. It seems that the mass-productive in-situ solution-free processes for all-organic thin-film transistors are possible by using the proposed method without vacuum breaking.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.2
• /
• pp.104-108
• /
• 2015

Al thin films were deposited on TiN/Si(100) via metal-organic chemical vapor deposition using N-methylpyrrolidine alane as a precursor. Characterization of the deposited films were investigated with SEM, XRD, ${\alpha}$-step, AFM, 4-point probe. The early stage of Al thin film deposition was analyzed by in-situ surface reflectance measurement with laser and photometer apparatus. The surface reflectance were changed greatly during the initial 30~40 seconds. There were two increases and two decreases in the surface reflectance, thus the sequence of Al films were deposited at 8 significant points of the surface reflectance change. Surface topograph and cross-sectional view of each film were analyzed with SEM. Al films were grown in the complex mechanism of Volmer-Weber and Stranski-Krastanov process.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1483-1484
• /
• 2000

Dielectric thin films of PLT(Pb(La.Ti)O3) for the application of highly integrated memory devices have been deposited on Pt/Ti/SiO2/Si substrates in situ by pulsed laser deposition(PLD). We have systematically investigated the variation of grain sizes depending on the condition of post-annealing and the variation of deposition rate. Both in-situ annealing and ex-situ annealing have been compared depending on the annealing time. C-V measurement, ferroelectric properties, leakage current and SEM were performed to investigate the electrical properties and the microstructural properties of Pb(La,Ti)$O_3$ films.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.2
• /
• pp.27-36
• /
• 2007

A recent study showed that MTBE can be degraded by Fenton's Reagent (FR). The treatment of MTBE with FR, however, has a definite limitation of extremely low pH requirement (optimum pH $3{\sim}4$) that makes the process impracticable under neutral pH condition on which the ferrous ion precipitate forming salt with hydroxyl anion, which result in the diminishment of the Fenton reaction and incompatible with biological treatment. Consequently, this process using only FR is not suitable for in-situ remediation of MTBE. In order to overcome this limitation, modified Fenton process using NTA, oxalate, and acetate as chelating reagents was introduced into this study. Modified Fenton reaction, available at near neutral pH, has been researched for the purpose of obtaining high performance of oxidation efficiency with stabilized ferrous or ferric ion by chelating agent. In the MTBE degradation experiment with modified Fenton reaction, it was observed that this reaction was influenced by some factors such as concentrations of ferric ion, hydrogen peroxide, and each chelating agent and pH. Six potential chelators including oxalate, succinate, acetate, citrate, NTA, and EDTA were tested to identify an appropriate chelator. Among them, oxalate, acetate, and NTA were selected based on their remediation efficiency and biodegradability of each chelator. Using NTA, the best result was obtained, showing more than 99.9% of MTBE degradation after 30 min at pH 7; the initial concentration of hydrogen peroxide, NTA, and ferric ion were 1470 mM, 6 mM, and 2 mM, respectively. Under the same experimental condition, the removal of MTBE using oxalate and acetate were 91.3% and 75.8%, respectively. Optimum concentration of iron ion were 3 mM using oxalate which showed the greatest removal efficiency. In case of acetate, $[MTBE]_0$ decreased gradually when concentration of iron ion increased above 5 mM. In this research, it was showed that modified Fenton reaction is proper for in-situ remediation of MTBE with great efficiency and the application of chelatimg agents, such as NTA, was able to make the ferric ion stable even at near neutral pH. In consequence, the outcomes of this study clearly showed that the modified Fenton process successfully coped with the limitation of the low pH requirement. Furthermore, the introduction of low molecular weight organic acids makes the process more available since these compounds have distinguishable biodegradability and it may be able to use natural iron mineral as catalyst for in situ remediation, so as to produce hydroxyl radical without the additional injection of ferric ion.

• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.74-80
• /
• 2019

$Nafion/TiO_2$ composite membranes were prepared via an in-situ sol-gel process with different immersing periods from 1 day to 7 days for the low humidifying proton exchange membrane fuel cell. As the immersing time increased, the $TiO_2$ content within the Nafion membrane increased. The contact angle decreased with the increased $TiO_2$ content in the composite membrane due to the increased hydrophilicity. The water uptake and proton conductivity reached to the highest level for 4 day immersing period, then decreased as the immersing period increased. A 7 days of immersing time was shown to be too long because too much $TiO_2$ aggregates were formed on the membrane surface as well as interior of the membrane, interfering the proton transfer from anode to cathode. Cell performance results were in good agreement with those of the water uptake and proton conductivity; current densities under a relative humidity (RH) of 40% were 0.54, 0.6, $0.63A/cm^2$ and $0.49A/cm^2$ for the immersing time of 1, 3, 4 and 7 days, respectively at a 0.6 V. The composite membrane prepared via the in-situ sol-gel process exhibited the enhancement in the cell performance under of RH 40% by a maximum of about 66% compared to those of using the recasting composite membrane and Nafion 115.

• Journal of Korean Vacuum Science & Technology
• /
• v.2 no.2
• /
• pp.85-91
• /
• 1998

The electrochromic behaviors of de-magnetron sputtered tungsten oxide thin films were investigated during coloration and bleach cycles using in situ real-time spectroscopic ellipsometry. Effective medium approximation and least-squares regression analyses were employed to investigate the electrochromic process. The optical properties of the tungsten oxide film were analyzed using the oscillator model and the evolution of the process using a reaction-limited model. In these analyses, we found that two different reaction rates were associated with the process. We ascribe this behavior to the microstructure of this films.