• Ocean Systems Engineering
• /
• 제7권3호
• /
• pp.179-193
• /
• 2017

Dynamic response analysis of offshore triceratops with stiffened buoyant legs under impact and non-impact waves is presented. Triceratops is relatively new-generation complaint platform being explored in the recent past for its suitability in ultra-deep waters. Buoyant legs support the deck through ball joints, which partially isolate the deck by not transferring rotation from legs to the deck. Buoyant legs are interconnected using equally spaced stiffeners, inducing more integral action in dispersing the encountered wave loads. Two typical nonlinear waves under very high sea state are used to simulate impact and non-impact waves. Parameters of JONSWAP spectrum are chosen to produce waves with high vertical and horizontal asymmetries. Impact waves are simulated by steep, front asymmetric waves while non-impact waves are simulated using Stokes nonlinear irregular waves. Based on the numerical analyses presented, it is seen that the platform experiences both steady state (springing) and transient response (ringing) of high amplitudes. Response of the deck shows significant reduction in rotational degrees-of-freedom due to isolation offered by ball joints. Weak-asymmetric waves, resulting in non-impact waves cause steady state response. Beat phenomenon is noticed in almost all degrees-of-freedom but values in sway, roll and yaw are considerably low as angle of incidence is zero degrees. Impact waves cause response in higher frequencies; bursting nature of pitch response is a clear manifestation of the effect of impact waves on buoyant legs. Non-impact waves cause response similar to that of a beating phenomenon in all active degrees-of-freedom, which otherwise would not be present under normal loading. Power spectral density plots show energy content of response for a wide bandwidth of frequencies, indicating an alarming behaviour apart from being highly nonlinear. Heave, being one of the stiff degrees-of-freedom is triggered under non-impact waves, which resulted in tether tension variation under non-impact waves as well. Reduced deck response aids functional requirements of triceratops even under impact and non-impact waves. Stiffened group of buoyant legs enable a monolithic behaviour, enhancing stiffness in vertical plane.

• International Journal of Aeronautical and Space Sciences
• /
• 제14권2호
• /
• pp.152-161
• /
• 2013

This paper presents a control effectiveness analysis of the hawkmoth Manduca sexta. A multibody dynamic model of the insect that considers the time-varying inertia of two flapping wings is established, based on measurement data from the real hawkmoth. A six-degree-of-freedom (6-DOF) multibody flight dynamics simulation environment is used to analyze the effectiveness of the control variables defined in a wing kinematics function. The aerodynamics from complex wing flapping motions is estimated by a blade element approach, including translational and rotational force coefficients derived from relevant experimental studies. Control characteristics of flight dynamics with respect to the changes of three angular degrees of freedom (stroke positional, feathering, and deviation angle) of the wing kinematics are investigated. Results show that the symmetric (asymmetric) wing kinematics change of each wing only affects the longitudinal (lateral) flight forces and moments, which implies that the longitudinal and lateral flight controls are decoupled. However, there are coupling effects within each plane of motion. In the longitudinal plane, pitch and forward/backward motion controls are coupled; in the lateral plane, roll and side-translation motion controls are coupled.

• 한국지진공학회논문집
• /
• 제16권4호
• /
• pp.37-52
• /
• 2012

이 연구에서는 감절점쉘요소의 개념에 근거한 새로운 4절점 곡면 쉘요소를 제시하였다. 회전장이 독립변수로 도입된 범함수에 의하여 면내회전자유도를 도입함으로써 개발된 쉘요소에서는 절점당 6자유도를 갖도록 하였다. 아울러 쉘요소의 면내거동 개선을 위하여 4개의 비적합변위형에 의한 비적합변위를 면내방향의 변위성분에 추가하였으며, 면외거동 개선을 위하여 대체전단변형률장이 적용되었다. 이 연구에서의 비적합변위형의 수치적 구현에 있어서 일정한 변형률상태를 표현할 수 있도록 하기 위하여 비적합변위형의 직접 수정법이 적용되었다. 이렇게 정식화된 쉘요소 강성행렬의 수치적분에 있어서는 부피적분을 위하여 9점 적분법이 사용되었다. 개발된 쉘요소는 바람직하지 못한 영에너지모드를 갖지 않으며, 일정한 변형률 상태를 표현할 수 있음을 확인하였다. 개발된 4절점 곡면 쉘 요소에 대한 다양한 수치예제를 통한 검증 결과, 전반적으로 양호한 거동을 보여주고 있음을 확인하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권3호
• /
• pp.313-321
• /
• 2012

Vibration analysis of a thin-walled structure can be performed with a consistent mass matrix determined by the shape functions of all degrees of freedom (d.o.f.) used for construction of conventional stiffness matrix, or with a lumped mass matrix. In similar way stability of a structure can be analysed with consistent geometric stiffness matrix or geometric stiffness matrix with lumped buckling load, related only to the rotational d.o.f. Recently, the simplified mass matrix is constructed employing shape functions of in-plane displacements for plate deflection. In this paper the same approach is used for construction of simplified geometric stiffness matrix. Beam element, and triangular and rectangular plate element are considered. Application of the new geometric stiffness is illustrated in the case of simply supported beam and square plate. The same problems are solved with consistent and lumped geometric stiffness matrix, and the obtained results are compared with the analytical solution. Also, a combination of simplified and lumped geometric stiffness matrix is analysed in order to increase accuracy of stability analysis.

• 한국전산구조공학회논문집
• /
• 제17권1호
• /
• pp.21-30
• /
• 2004

본 연구에서는 유한요소법을 이용한 채널단면을 갖는 복합재료 적층 구조물의 자유진동을 다룬다. 복합적층 절판구조물에 고차항 판이론을 적용하기 위하여 개발된 유한요소 프로그램은 Lagrangian 및 Hermite 보간함수를 병용하여 면내회전각 자유도를 포함한 절점 당 8개의 자유도를 갖는다. 전단보정계수의 가정을 필요로 하지 않고 전단변형의 3차항 비선형 특성이 고려된 본 논문의 절판 요소는 국부좌표계와 전체좌표계에 대한 좌표변환행렬에 의하여 요소 당 32×32의 국부요소행렬로 구성된다. 본 해석 프로그램의 결과는 기존의 고전적 이론 및 일차항 이론에 의한 문헌 결과와 비교ㆍ분석하였으며, 화이버 보강각도, 길이-두께비, 기하학적 형상 변화 등의 다양한 매개변수 연구를 수행하였다. 본 연구에서는 특히 경계조건 및 길이-두께비 변화에 따라 예측하기 힘든 복잡한 거동을 보이는 복합적층 채널단면 구조물의 자유진동에 대하여 정밀한 고차항 이론 적용에 의한 엄밀 해석의 필요성을 제기하였다.