• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.5
• /
• pp.748-763
• /
• 2003

Anaerobic rumen microorganisms mainly bacteria, protozoa and fungi degrade ligno-cellulosic feeds consumed by the ruminants. The ruminants in developing countries are predominantly maintained on low grade roughage and grazing on degraded range land resulting in their poor nutrient utilization and productivity. Hence, manipulation of rumen fermentation was tried during last two decades to optimize ruminal fermentation for improving nutrient utilization and productivity of the animals. Modification of rumen microbial composition and their activity was attempted by using chemical additives those selectively effect rumen microbes, introduction of naturally occurring or genetically modified foreign microbes into the rumen and genetically manipulation of existing microbes in the rumen ecosystem. Accordingly, rumen protozoa were eliminated by defaunation for reducing ruminal methane production and increasing protein outflow in the intestine, resulting in improve growth and feed conversion efficiency of the animals. Further, Interspecies trans-inoculation of rumen microbes was also successfully used for annulment of dietary toxic factor. Additionally, probiotics of bacterial and yeast origin have been used in animal feeding to stabilize rumen fermentation, reduced incidence of diarrhoea and thus improving growth and feed conversion efficiency of young stalk. It is envisaged that genetic manipulation of rumen microorganisms has enormous research potential in developing countries. In view of feed resource availability more emphasis has to be given for manipulating rumen fermentation to increase cellulolytic activity for efficient utilization of low grade roughage.

• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.288-290
• /
• 2006

An efficiency improving method for Uninterruptible Power Supply System(UPS) was developed by using OP-AMP based application circuits such as voltage detection device, current detection device and static switch control device. The efficiency improving algorithm was made by mixing the operating concepts of On-Line type UPS with the operating concepts of Off-Line type UPS. The UPS' inverter does not work if the UPS' output load current is not higher than the low load operating current which is about 0-30(%) of the UPS' output load capacity. The low load operating current is adjustable within the half of the UPS' output load capacity. If the UPS' output load current is rising over than the low load operating current, the UPS' inverter starts working and the inverter output power feeds to the loads of UPS. If UPS' input power breaks out while UPS' inverter does not operate because the load current is low, the inverter starts working within 4(ms) with excessive output voltage which is ${\pm}$8(%) of normal UPS' output voltage. Like these. UPS can continuously feeds power to it's load device and reduce power consumptions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.9
• /
• pp.988-993
• /
• 2004

Luminescence characteristics of Ag-doped ZnO as the quantum dot materials to increasing the efficiency on dye-sensitized solar cells (DSC) have been studied. Ag doped ZnO powder was produced by the self-sustaining combustion process using ultrasonic spraying heating method. Luminescence wavelength region of the ZnO by Ag doping was shifted to longer wavelength. Tn the case of the Ag doped ZnO powder, broad luminescence spectrum centered on 600nm was observed. On the other hand, we compared PL data of RTA treated ZnO:Ag film at various temperatures because the front electrode of solar cell was in need of the sintering process. In XRD and PL data for RTA treated film at the 500$^{\circ}C$ showed good property. And, it was found that the grain size wasn't growing but only optical property was changed. According to the result of XRD, PL, absorption, emission spectrum and DV-X${\alpha}$ used in theoretical calculation, it is considered to be possible to use Ag doped ZnO as quantum dot material for improving DSC efficiency.

• Journal of Biosystems Engineering
• /
• v.27 no.4
• /
• pp.317-326
• /
• 2002

Characteristics of a twin-fluid spray with ultrasonic vibration were examined in order to obtain a high efficiency of cold-fog spray of the automatic pest control machine which has been widely used in protected horticulture recently. An electrostrictive vibrator of PZT BLT and a magnetostrictive $\pi$-type vibrator were used applied as the ultrasonic transducers with a frequency of 28 kHz. All experiments were conducted in 4 methods of spray ; a conventional spray method without ultrasonic forcing, an indirect vibration method with ultrasonic forcing, an improving-quality method by ultrasonic forced within liquid, and a combined-use method with both of the indirect vibration method and the improving quality method. It was found that the ultrasonic energy increased the atomization efficiency of spray droplets about 10% and especially much more in the case of the combined-use method.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.43 no.3
• /
• pp.204-215
• /
• 2020

Efforts on the continued increase of local government's fiscal spending related to improving the residential environment are desirable to counter the declining phenomenon of urban decline. At the same time, however, it is also important to know how to operate limited finances more efficiently to improve the residential environment. This study aims to contribute to the rational allocation of fiscal expenditure and the creation of productive results for the improvement of the settlement environment. To this end, this study analyzed the efficiency of financial expenditure related to the improvement of the residential environment in 225 local governments nationwide. The relationship between financial expenditure and residential environmental performance was also measured and the CCR, BCC and SBM models were used to measure efficiency. The analysis showed that most local governments need to scale back their fiscal spending related to improving the government environment. In addition, it was required to prepare feasible spending plans by bench-marking the processes of residential environment improvement projects in areas such as Haman-gun, Jongno-gu, Seoul, and Seocho-gu, which are considered to be under efficient operation.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.323-326
• /
• 2008

This paper presents a cooling system using thermoelectron for improving the output of BIPV module. The temperature characteristic in regard to improving the output of BIPV system has rarely teen studied up to now but some researchers only presented the method using a ventilator. The cooling system efficiency of BIPV module applied to a ventilator mainly depends on the weather such as wind, insolation etc. Because the cooling system of BIPV module using a ventilator is so sensitive, that is being set off by wind speed at all time but is unable to operate in the NOCT(Nominal Operating Cell Temperature) which is able to make the maximum output. The paper presents the cooling system using thermoelectron so as to solve such problems. The temperature control of thermoelectron can be controlled independently in the outside environment because that is performed by micro-controller. The temperature control of thermoelectron, also, can be operated around NOCT through algorithm of the temperature control. Therefore, outputs of the whole system increase and the efficiency rises. The paper demonstrates the validity of proposed method by comparing the data obtained through a experiment of the cooling method of BIPV using a ventilator and proposed thermoelectron.

• Proceedings of the Korean Society of Embryo Transfer Conference
• /
• 1998.05a
• /
• pp.12-28
• /
• 1998

The technology of creating transgenic animals has a potential value in improving productivity and disease resistance of animals, gene therapy, drug pharming and production of model animals for certain diseases. Up to date, fairly low success rate of production of transgenic animals and a pronounced variability with respect to the expression of transgenes have been much observed. The mechanisms how to integrate the injected genes with a certain part of the genomes are unknown yet. Many techniques in gene transfer, beside microinjection, have been introduced and explored thus to improve the production efficiency of transgenic animals. In this article, the methods and efficiency of gene-transfer techniques, the detection and preselection of transgenes in embryos by PCR- and GFP-screenings and cloning of preselected transgenic embryos by nuclear transplantation are described and discussed. Some experimental results showed that the early screening and selection of integration of the injected gene with embryonic genome by polymerase chain reaction(PCR) and green fluorecence protein(GFP) were promising methods. Further, the application of nuclear transplantation technology to cloning and multiplication of the positively integrated genes in the cleaving embryos and embryonic cells will be beneficially used for the mass production of transgenic embryos and consequently improving the production efficiency in transgenic animals.

• Journal of Power Electronics
• /
• v.19 no.3
• /
• pp.761-770
• /
• 2019

This paper proposes a hybrid phase windings excitation method for improving the efficiency of a 7-phase brushless DC (BLDC) motor in the electric propulsion system of a ship. The electrical losses of a BLDC motor system depend on the operating region and the number of excited phase windings (2-phase, 4-phase or general 6-phase windings). In this paper the operating region and torque/speed characteristics according to the motor rotation speed and propeller load are analyzed for a number of excitation methods. In addition, it analyzes the electrical losses of the system under each of the excitation methods in the entire operating region of the motor. In every sampling time, the proposed control method calculates the electrical loss of the system for each of the excitation methods and operates a 7-phase BLDC motor by selecting the excitation method that results a decreased electrical loss at the operating speed. The usefulness of the proposed control algorithm is verified through experimental results.

• Tribology and Lubricants
• /
• v.38 no.6
• /
• pp.227-234
• /
• 2022

Recently, the demand for improving energy efficiency has rapidly increased because of the growing concerns over environmental issues. In this work, the tribo-test and simulation for the initial wear and lubrication performance were performed for the piston pin in the small end system of the connecting rod of a marine engine, to obtain useful data for improving the efficiency of marine engine systems. In addition, a diamond-like carbon (DLC) coating was applied to the piston pin to explore feasibility of eliminating the bush used in the system. The initial wear and lubrication characteristics between the uncoated piston pin and bush were compared with that between the DLC-coated piston pin and connecting rod in the tribo-test. The simulation for the wear and lubrication performance according to the wear progression was conducted based on the data obtained from the test. The wear characteristics were quantitatively assessed by the wear depth and wear volume, and the lubrication performance was characterized with the change of pressure and minimum oil film thickness with respect to the crank angle. It was found that the DLC-coated piston pin may provide better initial wear characteristics and lubrication performance. The results of this work may provide fundamental information for marine engines with improved efficiency.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• fall
• /
• pp.33-36
• /
• 2021

In this paper, we propose a new method for improving compression efficiency of immersive video using reinforcement learning. Immersive video means a video that a user can directly experience, such as 3DOF+ videos and Point Cloud videos. It has a vast amount of information due to their characteristics. Therefore, lots of compression methods for immersive video are being studied, and generally, a method, which projects an 3D image into 2D image, is used. However, in this process, a region where information does not exist is created, and it can decrease the compression efficiency. To solve this problem, we propose the reinforcement learning-based filling method with considering the characteristics of images. Experimental results show that the performance is better than the conventional padding method.