• Journal of Satellite, Information and Communications
• /
• v.12 no.4
• /
• pp.146-151
• /
• 2017

This paper proposes a transmission algorithm that optimizes transmission power and sub-channel allocation to maximize energy efficiency considering characteristics of the channel impedance of power lines in power line communication systems. Since the received power at the receiver is influenced by the characteristics of the power line channel, it is necessary to consider channel characteristics when developing a transmission strategy in a power line communication systems. In addition, the energy efficiency should be optimized while meeting the practical constraints, such as the maximum transmission power limit of the transmitter and minimum quality of service for each user. In the computer simulation, we confirm that the energy efficiency of the proposed algorithm is improved compared to baseline schemes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.68-72
• /
• 1991

In this study, to improve temperature stability 0.05 Pb(Sn$\_$$\frac{1}{2}$/Sb$\_$$\frac{1}{2}$/O$_3$ - 0.35PbTiO$_3$ - 0.60PbZrO$_3$ + 0.4[wt%]MnO$_2$ piezoelctric oeramics of low dielectric constant and large mechanical quality factor were manufactured with the addition of Cr$_2$O$_3$by Hot Press method. And the SAW delay line was fabricated and the propagation characteristics of SAW was investigated, and the SAW filter was fabricated on C4 added by 0.2[wt%] Cr$_2$O$_3$and its frequency characteristics was investigated. The specimen, whose propagation characteristics of surface acoustic wave were the best, was C4 added by 0.2[wt%] Cr$_2$O$_3$, and its electromechanical coupling factor(ks$^2$) was 3.11[%] and its temperature coefficient of the center frequency (C$\_$fo/) was -21.27[ppm/$^{\circ}C$]. The 31[MHz] SAW IF filter of C4 scarcely had diffraction phenomena and its group delay time was 1.4673 ${\pm}$40[ns] in the pass band, and the insertion loss was -24.419[dB] on no impedance matching.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.4A
• /
• pp.256-266
• /
• 2003

In this paper, scattering characteristics of the rectangular waveguide with elliptical conducting post and equivalent impedance of post are analyzed by mode matching method and generalized scattering method. The scattcring characteristics of rectangular waveguide are varied by the height and eccentricity of elliptical conducting post. When the height of post(2.54mm, 4mm) is small, variation in scattering characteristics appears in total simulated frequency. But as the height of post(7.62mm, 9mm) is increased, it is dominant in higher frequency. The simulated result shows good agreement with the HFSS's result. Proposed structure and analysis method are easily applied to the design and manufacture of waveguide component with elliptical conducting post.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.3 s.36
• /
• pp.235-241
• /
• 2005

Incorporation of solid electrodes frequently involves plasma-based processing. The effect of plasma can influence the physical characteristics, depending on the magnitude in plasma. The undesired feature of plasma-induced damage should be prevented in characterizing the ultra-thin materials, such as ultra-thin films and organic monolayers. The current work at first proves the applicability of a liquid phase electrode in the electrical/dielectric properties through comparative work using Al and Hg on ultrathin $Al_2O_3$ films deposited through atomic layer deposition at low temperature: Two types of metals such as Aluminum (Al) and mercury (Hg) were used as electrodes in $Al_2O_3$ thin films in order to investigate the effect of electrode preparation on the current-voltage characteristics and impedance features as a function of thickness in $Al_2O_3$ film thickness. The success of Hg in $Al_2O_3$ thin films is applied to the AC and DC characterization of the organic monolayers obtained using the Langmuir-Blodgett method. From the DC current-voltage characteristics, the diode-like response is found to originate from the bulk response of the organic materials, evidenced by the fact and the capacitance is inversely related to the absolute thickness of organic layers.

• Journal of Sensor Science and Technology
• /
• v.1 no.1
• /
• pp.13-21
• /
• 1992

We have constructed the magneto-operational amplifier(MOP) using the advantages of Hall device and an operational amplifier. The MOP necessarily requires a high impedance circuit, a differential-to-single-ended convert-sion circuit and feedback-input-element for operational amplifier characteristics. We have presented a new differential-to-single-ended conversion operational amplifier(DSCOP) having such characteristics. We have designed the MOP using the DSCOP and Hall device and simulated its characteristics, and finally we have constructed the system with discrete elements, and measured its magnetic characteristics.

• Journal of electromagnetic engineering and science
• /
• v.17 no.1
• /
• pp.1-8
• /
• 2017

This paper introduces a technique to obtain the broadband characteristics of circularly polarized antennas using an L-shaped probe. A waveguide antenna is suitable for obtaining high gain and handling convenience in some applications; however, the asymmetrical structure of the L-shaped probe results in cross-polarization and frequency dependence on the field distribution of higher-order modes (HOM). In addition to the basic characteristics of a waveguide antenna with an L-shaped probe, the author discusses some techniques to reduce the HOM and cross-polarization. As a result, the 3-dB axial ratio (AR) is obtained with the fundamental mode even when the frequency is expanded to the region for HOM of TM. This reduction is mainly due to the cutoff structure to the TM mode around the short wall of the waveguide. Furthermore, some aperture modification techniques can reduce the cross-polarization in a wide range of angles in the radiation pattern. Such techniques and their mechanisms are discussed in this paper. The obtained performance shows that the proposed antennas have a wide range of angles of 3-dB AR in the radiation pattern, broadband characteristics in impedance and AR, and low variation in group velocity.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.2
• /
• pp.77-81
• /
• 2009

Air-gap was introduced to suppress the saturation of the iron core comprising the flux-lock type superconducting fault current limiter (SFCL) with parallel connection of two coils. However, the air-gap makes the impedance of this SFCL decreased and can result in unusefulness of the SFCL. To analyze the current limiting characteristics of the SFCL with the air-gap, the experimental circuit for short-circuit test was constructed. Through the comparison with the current limiting characteristics of the SFCL without air-gap, the merit and the demerit of the flux-lock type SFCL with the air-gap were discussed.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.736-741
• /
• 2005

This paper presents electric characteristics analysis and safe configuration for extension power supply between existent 6.6kV ungrounded distribution system and establishment and improvement 22.9kV direct grounding distribution system. For this, we model 6.6kV ungrounded and 22.9kV direct grounding distribution system of urban underground, ground region. and rural electrical, unelectrical region using PSCAD/EMTDC and analyze voltage drop, charging current, ground and short fault through simulation. To analyze electric characteristics of extension power supply, we simulate extension power supply of overhead line of 6.6kV ungrounded system and underground line of 22.9kV direct grounding system of rural electrical region and propose operation condition for safe extension power supply through result of analysis. Characteristics of voltage drop, charging current, ground and short fault appear almost similarly with electrical characteristic of direct power supply. However, because unbalance of phases may cause relay's malfunction of ungrounded system and ground fault current of direct grounding system may demage facilities of ungrounded system, we propose safe system configuration such as impedance grounding system of neutral point.

• Journal of Hydrogen and New Energy
• /
• v.30 no.1
• /
• pp.43-48
• /
• 2019

This study investigates the electrochemical characteristics of the hybrid cell that combined the advantageous characteristics of Li secondary battery and supercapacitor, high energy density and high power density, respectively. Electrochemical behaviors of the hybrid cell was characterized by charge/discharge, cycle and impedance tests. The hybrid cell using Li secondary battery and supercapacitor had better discharge capacity and cycle performance than that of using Li secondary battery only. Proper design of such a hybrid cell system is expected to result in substantial benefits to the well being of the Li secondary battery. The hybrid cell involving Li secondary battery for high energy density and supercapacitor for high power density may be the possible solution for future energy storage system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.401-412
• /
• 2003

In this paper, a broadband phase shifter structure using a new switched network was proposed. A new reference network is composed of coupled lines and 45$^{\circ}$open and short stubs, which are shunted at the edge points of a main line, respectively, A delay network is composed of only a standard transmission line. It is possible to design a broadband 180$^{\circ}$phase shifter that phase dispersive characteristics by an impedance ratio R of coupled lines and greater phase dispersive characteristics by characteristic impedances Zm, Zs of a main line and stubs are used together. By considering a structure symmetry, the even and odd mode analysis was performed to obtain theoretical S-parameters of the proposed phase shifter. Also, through computer simulation on the basis of derived equations, design graphs were presented to optimally design a 180$^{\circ}$broadband phase shifter. Design graphs provide the values of characteristic impedances Zm, Zs, and I/O match and phase bandwidths. To verify electrical performances of the broadband phase shifter proposed in this paper, low different 180$^{\circ}$phase shifters, operated at the center frequency 3 GHz were designed and fabricated using design graphs, and were experimented. One of them was designed as a standard Schiffman structure to compare with electrical performances. Measured results of each phase shifter to satisfy simultaneously design conditions of I/O match （VSWR=1.15:1) and maximum phase deviation $({\varepsilon}_{{\Delta}{\phi}}＝{\pm}2^{\circ})$ were well in agreement with corresponding simulation results over impedance match and phase error bandwidths, and showed broadband characteristics.