• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.5
• /
• pp.456-462
• /
• 2013

Eco-friendly material applied to building would be one of the materials which is must developed for global environmental conservation and reduction of carbon dioxide. For development of eco-friendly material, a cellulose absorber has been developed with waste paper through adjustment of various mix proportions. The developed cellulose absorber has been tested for its acoustic properties such as absorption coefficient and dynamic stiffness. The absorption coefficient was evaluated by developing six samples and using impedance tube and reverberation chamber. As a result of the evaluation, 0.64(NRC) was secured in absorption coefficient and 4.7 $MN/m^3$ was indicated in dynamic stiffness. Also, for practical use of developed absorbers as inner heartwood in drywall, comparison test of sound reduction index was performed with existing glass wool absorbers and constructed drywall of gypsum board. The results have shown 55 dB(Rw) of sound reduction index in glass-wool wall and 46 dB(Rw) in cellulose.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12B
• /
• pp.1724-1732
• /
• 2001

In this paper, a technique for increasing the bandwidth of microstrip array antennas using the parallel coupled lines on a single layer is presented. Four types of wideband microstrip array antenna are designed and the characteristics of each type are analyzed. In addition, an iterative method using a distributed network is proposed to design the parallel coupled lines as a wideband impedance matching network. Measurements show that the proposed antennas provide wider bandwidths ∼1.7 times those of conventional microstirp array antennas, while the sizes of proposed antennal are the same as that of a conventional array. And low cross-polarization level can be obtained through symmetrical locations of the parallel coupled lines section

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.142-142
• /
• 2011

Microwave diagnostics method for plasma science and engineering is vigorous research area for its good characteristics such as high sensitivity, reliability, and broad measurement spectrum from low density plasma to high density. We investigate mechanism of microwave probes (hairpin, impedance and absorbtionf probe) and apply it for interpretation of full transmitted spectrum of cutoff probe. Mechanism of the spectrum having same key roles of I-V curve of Langmuir probe is not exactly revealed yet in spite of its importance. This study elucidates physics behind it using a circuit model and E/M wave simulation. Circuit model reveals exact cut-off peak frequency taking account of a collision frequency and a plasma frequency and it enable precise diagnostics of plasma densty from low pressure to high pressre. Cut-off like peaks have been obstacle for choosing cut-off peak is analyzed by E/M simulation and one of cutoff like peaks made by probe holder used for acquire plasma density with cutoff peak applying the hairpin relation. Furthermore, phase difference method for plasma density is conducted. This method uses a single microwave frequency source and it is low-priced.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.93.2-93.2
• /
• 2012

연료전지는 전기화학반응을 이용한 발전 장치로서 기존 장치에 비하여 발전 효율이 높아 화석연료를 사용하면서 현재 당면 과제인 $CO_2$ 배출량 절감이 가능하고, 환경 보전성이 우수하여 미래의 전원으로 많은 연구개발이 진행되고 있다. 특히 제3세대 연료전지라 불리는 고체산화물 연료전지(Solid Oxide Fuel Cell이하 SOFC)는 고가의 외부 개질 장치 없이도 연료가 갖는 화학에너지를 연소과정 없이, 공기와 $H_2$, CO, $CH_4$와 같은 환원성 가스를 공급받아 $600{\sim}1000^{\circ}C$에서 전기화학적 반응을 통하여 직접 전기를 얻는 방식이며, 낮은 소음과 진동으로 인하여 온 사이트(On-site) 발전이 가능한 장점이 있는 연료전지이다. Decalcomanie는 전사용지에 Screen printing하여 건조 후 coating하는 방법으로 기존의 여러 coating 방법보다 다전지셀 제작이나 Buffer layer의 적용이 용이하고, 소재의 크기나 두께조절이 간편하며, 구성층의 표면조도나 굴곡에 대응이 용이한 방법이다. 새로운 Decalcomanie를 사용하여 평관형 다전지식 SOFC Cell 제작 및 각 Buffer layer에 적용, Screen printing법과 동일한 Cell 제조 후 MPD와 Impedance 분석을 통하여 Support 위에 전사지를 이용, 적층한 Cell의 전기화학적 특성에 관하여 분석하였다.

• Journal of Broadcast Engineering
• /
• v.18 no.6
• /
• pp.911-918
• /
• 2013

The proposed print antenna using Finite Difference Time Domain(FDTD) method is analyzed in this paper. A low radiation resistance and an ultra-wide band of this antenna are also presented. The propagation process of the reflected wave and the electric field distribution in the time domain are calculated in respectively. The antenna parameters are optimized for the maximum band width, return loss, input impedance, and radiation pattern in the frequency domain using Fourier transforming. The experimental bandwidth of the antenna is 1.85GHz~6.35GHz for the VSWR less than or equal to 2.0. The measured results are relatively in good agreement with the FDTD results. The proposed antenna can be applied to various applications such as UWB, broadcasting-network system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.2
• /
• pp.278-285
• /
• 2000

This paper presents the basic characteristics of the beam tilting dipole antenna element in which one reactance element is used for the impedance matching at the feed point. The radiation pattern is tilted by the properly determined driving point position, and the loading reactance is used to obtain forced resonance without great changes in tilt angle. The numerical results demonstrate that the reactance element should be loaded in the region where the driving point is placed to obtain forced resonance of the antenna with little changes in beam tilt angle. In case the proposed forced resonant beam tilting antenna with $0.8\lambda$ length is driven at $0.2\lambda$ from the center, the main beam tilt angle o.5 57.7 degrees, the highest power gain of 8.6 dB are obtained.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.878-883
• /
• 2003

New feeding structures using linearly and exponentially tapered lines to planar microstrip resonators are proposed. These can overcome the design problems from coupling losses and impedance mismatching by increasing the coupling efficiency. The variation of its feeding angle is evaluated for the insertion loss and bandwidth and the feedline length is optimized at ${\lambda}_g$/2. The ring resonators and patches fed by the tapered line have been designed and implemented. The experimental results show that the insertion loss is enhanced by about 7 dB. Both rings and antennas are better matched, without disturbing the single-mode resonance or distorting their radiation pattern

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.6
• /
• pp.866-878
• /
• 1999

In this paper, stripline circulator including a ferrite resonator which is consisted of a circular disk and two annuli disks is designed and fabricated. Using RGF(Recursive Green Function) technique, electromagnetic field of port and input impedance is presented. The circulator characteristics are compared according to the ferrite arrangement, bias field intensity and port width. The pass-band frequency of the fabricated circulator using the designed data is from 1.55 GHz to 2.95 GHz, the reflection coefficient $S_{11}$ of input port is -30 dB, and the transmission coefficient $S_{21}$ between input port and isolation port is -28 dB at resonating point 2.38 GHz.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1286-1291
• /
• 2003

Quench behavior of resistive superconducting fault current limiters (SFCLS) with various pattern shapes was investigated. The pattern shapes employed were meander, bi-spiral, and spital shapes of identical line width, gap and margin. SFCLS were fabricated from YBCO thin films grown on two-inch diameter Al$_2$O$_3$ substrates under the same conditions. The total length of current limiting paths was the shortest at the spital shape due to its larger useless space. Inductance component of SFCLs with the spiral shape was around two times as high as those of other two shapes. This is not desirable since impedance characteristics of existing power systems can be changed. Resistance rise of current limiting elements was low at a spiral shape before the whole quench completion, which may act as a disadvantage for simultaneous quench in serial connection between current limiting elements, but the temperature tended to have similar values at higher voltages. On the other hand, hi-spital shape was severe at insulation level between current limiting lines. When these aspects were considered, we concluded that a meander shape was appropriate to design for a resistive SFCL based on thin films except the concentration of electric field at edge areas of strip lines.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2048-2050
• /
• 1998

An uninterruptible power supply(UPS) with parallel operation is used to increase the power capacity of the system or to secure higher reliability at critical loads. In the parallel operating system composed of the multiple UPSs, load-sharing, i.e. current balance control between them is key technique. Because of its low impedance and quick response characteristics, inverter output current changes very rapidly and thereby easily researches an overload condition. The difference between total load current divided by number of operating inverters and its own current is detected as unbalanced current. Then frequency and voltage are controlled to minimize the active component and the reactive component. A good performance of the proposed load-sharing technique is verified by experiments in the parallel operating system with two 40kVA UPSs.